Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Urban Green Energy UGE
Summary of Contents for Urban Green Energy UGE
- Page 1 UGE WEATHER STATION WIND AND AIR PRESSURE Operation Manual...
-
Page 2: About This Manual
ABOUT THIS MANUAL Thank you and congratulations on selecting the Urban Green Energy weather station! We are positive you will enjoy the benefits of accurate weather readings and the precise radio controlled time information that our instruments offer. In particular, the included anemometer will highlight the opportunity of installing a Wind Turbine. -
Page 3: Table Of Contents
SUMMARY About this manual ...........................2 LCD Display ............................5 Set up Guide ............................6 Setting up the base station and transmitter ..................6 Register transmitter ........................6 Mounting the sensor ........................7 Positioning ............................ 10 Program Mode ..........................11 Time ............................. 11 Date.............................. 11 Wind ............................12 Rain .............................. - Page 4 USB cable and a PC software package on CD-ROM. An added feature of the UGE Weather Station is the readout of all measured and displayed time and weather data on a PC.
-
Page 5: Lcd Display
LCD DISPLAY 1. Time 2. Wind direction 3. Barometric Pressure 4. Barometric trend 5. Indoor Temperature 6. Outdoor Temperature 7. Memory 8. Date 9. Rainfall 10. Weather Forecast 11. Indoor Humidity 12. Outdoor reception signal 13. Outdoor Humidity Note: The presence of the "Alarm-On icon" in the section means that the particular alarm has been enabled. -
Page 6: Set Up Guide
SET UP GUIDE Before placing and installing all components of the weather station at their final destination, please set up the weather station with all parts being nearby for testing the correct function. SETTING UP THE BASE STATION AND TRANSMITTER Insert two pieces of LR6 (AA size) batteries into the transmitter, the LED located in the middle front case of transmitter will be turned on for 4 seconds, after which the transmitter will be functioning. -
Page 7: Mounting The Sensor
MOUNTING THE SENSOR Important Notes: On the edge of wind direction sensor, there are four alphabet letter of ―N‖,‖E‖,‖S‖ and ―W‖ representing the directions North, East, South and West. Wind direction sensor has to be adjusted so that the directions on the sensor are matched with your real location. Permanent wind direction error will be introduced when the wind direction sensor is not orientated correctly during installation. -
Page 10: Positioning
POSITIONING Once you have verified that all of the components of the weather station are working, they can be positioned in their permanent places. Before permanently mounting, make sure that all components work properly together at their chosen mounting or standing locations. If for example there appears to be problems with the 433 MHz radio transmission, it can generally be overcome by moving the mounting locations. -
Page 11: Program Mode
PROGRAM MODE The base station has six keys for easy operation: MENU key, UP/+ key, DOWN/- key, ENTER key, HISTORY key, ON/OFF key Note: Because of the default settings already determined by the manufacturer it may not be necessary for the majority of user to perform-except the relative pressure(see further down)-any further basic settings and changes, however, can be easily made. -
Page 12: Wind
120 seconds. The corresponding value, ‗HI AL‖ or ―LO AL‖ and the alarm symbol are flashing until the weather condition doesn‘t meet the user set level. Press any key to mute the alarm. WIND - Press the MENU key the third time to select the WIND section, WIND section digits will start flashing. -
Page 13: Weather Forecast Tendency
- Press the MENU key the fifth time to select the PRESSURE section, PRESSURE section digits will start flashing. Enter the pressure display mode (relative and absolute pressure. Default absolute pressure), press the UP/+ or DOWN/- key to select the display. - Press ENTER key to select the following modes, then press the UP/+ or DOWN/- key to select the display or set the value: ... -
Page 14: Indoor Temperature
Notes to pressure sensitivity setting for weather forecasting: The pressure threshold can be set to suit the user‘s requirement for weather forecasting from 2- 4hPa (default 2hPa). For areas that experience frequent changes in air pressure requires a higher hPa setting compared to an area where the air pressure is stagnant. -
Page 15: Outdoor Temperature
the ON/OFF key to on/off the alarm. If alarm is enabled, an alarm symbol appears in the display indicating the alarm function has been enabled - Press ENTER key to select the following modes: The indoor humidity low alarm setting. Press the ON/OFF key to on/off the alarm. If alarm is enabled, an alarm symbol appears in the display indicating the alarm function has been enabled... -
Page 16: Reset To Factory Default Settings
section area (History data saving interval can only be changed using the PC software that comes with this product, the default history data saving time interval is preset to 30 minutes prior to shipment). 2) Press the HISTORY key again will trigger the memory clear procedure: the word of ―CLEAR‖ will be flashing;... - Page 17 If you run the program for the first time, the current weather display will be displayed and at the sub line of the window, the program will show related information regarding the read of all history data into the PC. Please note however, when there is large amount of data is being uploaded, it will take a few minutes time before the system can respond to your setup settings.
- Page 18 When memory is full, it will take about two minutes to upload all history data into PC and it takes another two minutes to process all history data for graphic display. Further detailed PC software user manual can be found from the help menu.
-
Page 19: Specifications
SPECIFICATIONS Outdoor data Transmission distance in open field : 100m(300 feet) Frequency : 433MHz Temperature range : -40° C--65° C (-40℉ to +149℉) Accuracy : + / - 1 ° C Resolution : 0.1° C Measuring range rel. humidity : 10%～99% Accuracy : +/- 5%... - Page 20 Please help in the preservation of the environment and return used batteries to an authorized depot. All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher.
-
Page 21: Easyweather Pc Software User Manual
EASYWEATHER PC SOFTWARE USER MANUAL 1. GENERAL INFORMATION This Weather Station is a high quality, easy to use weather monitoring system which reads, displays and records the weather data from internal as well as external sensors. Besides the internally measured values for indoor temperature, indoor humidity and air pressure the outdoor sensor will take data for temperature and humidity, wind and rainfall. - Page 22 All the settings from the base unit is mirrored into the PC software, so once you have done your setting on the base unit, then you don‘t need to make any setting changes on the PC software. However you can still easily make any setting changes you wanted from the PC and download the changes into the base station (the setting change will be refreshed when next full minute arrives on the base station).
-
Page 23: Function Button
Function button: : Display and setup system configuration This section is used to set up PC software display, base station units, as well as able or disable the corresponding alarm function. Once you made your choice, press Save to make the setting effective. : Display and setup system alarm value... - Page 24 This section is used to set the desired time, high or low alarm value for the base unit. Once you made your choice, choose Save to make the setting effective. If you don‘t want to make any change, just press Cancel and exit without change. : Display min and max recorded value...
- Page 25 This section is used to display the recorded min and max value recorded with time stamp. Min/Max reset can only be done through key operation on the base station. : display listed history data...
- Page 26 This section is used to display recorded history data in a spread sheet. If you wanted to see all history data in a desired time period, choose the time duration and press Search to reload the history data. With the Export button, you can export the selected history data into text format file for other application purpose.
- Page 27 In this section, you can see the history data plotted in graph format for easier observation. If you want to see more details, just use your mouse to select the area you wanted and the display will be automatically updated in more detailed scale:...
- Page 29 Also you can see the graph in 3D mode by selecting the 3D check box:...
-
Page 30: What To Do If Graph Function Is Not Working
You can change the Y axel by scrolling the mouse up and down roller. What to do if graph function is not working This is the most encountered problem with this software. To make the graph function working properly, please check the following step: 1, find the folder where the ―EasyWeahter.exe‖... - Page 31 Special Notes about time synchronization between PC and sub-station: The PC software obtained its own time scale through the time interval marker from the base station history data, and the PC software automatically synchronizes the weather data with a time stamp calculated.