Denon S-102 Service Manual page 55

QQ
3 7 63 1515 0
Pin Port
No Function
81 P123
82 P122
83 P121
84 P120
85 VCC2
86 P30
87 VSS
88 P27
89 P26
90 P25
91 P24
92 P23
93 P22
94 P21
95 P20
96 INT5
97 P16
98 INT3
99 P14
100 P13
101 P12
102 P11
103 P10
104 P07
105 P06
TE
L 13942296513
106 P05
107 P04
108 P03
109 P02
110 P01
111 P00
112 P117
113 P116
114 P115
115 P114
116 P113
117 P112
118 P111
119 P110
120 P107/AN7
121 P106/AN6
122 P105/AN5
123 P104/AN4
124 P103/AN3
125 P102/AN2
126 P101/AN1
127 AVSS
128 SW1_IN
www
.
http://www.xiaoyu163.com
Port
Port Name
setting
O SAN_MOSI
O /CODEC_RST
O PRE_MUTE_SUB
O HP_MUTE_SUB
- VCC2
O BE/_DIR
- VSS
O CODEC_CE
O NC(L:Output)
O DSP_IO_MUTE
O /AD/DIG
O /ERR_MUTE
O /BSE
O NC(L:Output)
O NC(L:Output)
INT /PROTECT
O NC(L:Output)
INT /REMOCON
O NC(L:Output)
O PRE_MUTE_MAIN
O /COMP_MUTE
O /S/V_MUTE
O /BE RST
O DRV_ON
O SYS_REQ
I BE ON
O NC(L:Output)
O NC(L:Output)
O /DIR_RST
O DIR_CE
O DIR/CODEC_CK
I DIR_MISO
O DIR/CODEC_MOSI
O /DSPROM_RST
O /DSP_RST
O DSP_CS
I FLAG0
O FAN_ON
O FAN SPEED
I Pull uÇê
AD KEY2
AD KEY1
AD KEY0
AD MODE2_S102
AD MODE1_S102
O Pull up
- AVSS
AD SW1_IN
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
Serial Data output to TUNER/RDS IC
Reset output to CODEC
MUTE output to PRE OUT. H:MUTE
MUTE output to HEAD PHONE output. H:MUTE
Positive power
Select audio line output.(H:ESS,L:DIR)
GND
Chip Enable output to CODEC
Not Used:N.C.
DSP IO MUTE output(H:Mute)
Select audio line output.(H:DIGITAL, L:ADC IN)
MUTE output at DSP Error.
Bit Stream Enable output(L:Enable)
Not Used:N.C.
Not Used:N.C.
Protect Signal input.
Not Used:N.C.
Remote Control signal input
Not Used:N.C.
MUTE output to Output(H:Mute).
COMPONENT VIDEO Mute output(H:Mute)
S/COMPOSITE VIDEO Mute output(H:Mute)
Reset output to ESS
DRIVE POWER ON output(H:P.ON)
SYSTEM REQEST output to ESS.
Q Q
3 6 7 1 3 1 5
Active Flag input from ESS.
Not Used:N.C.
Not Used:N.C.
Reset output to DIR.
Chip Enable output to DIR
Serial Clock output to DIR/CODEC.
Serial Data input from DIR.
Serial Data output to DIR/CODEC
Reset output to DSP ROM.
Reset output to DSP.
Chip Select output to DSP
DSP FLAG0 input
FAN ON/OFF output.H:FAN ON
FAN SPEED Control output(H:Slow L:Fast)
Pull up
Unit Operation Button input2
Unit Operation Button input1
Unit Operation Button input0
Initial Setting input for Region No of DVD.
Initial Setting input the destination.(E2,E3)
Pull up
GND
Select signal input of Video Signal. (H:HDMI/M:PROGRE/L:INTERLACE)
[ ]:Reserved
co
.
55
9 4 2 8
Explanation
0 5 8 2 9 9 4 2 8
m
S-102
9 9
9 9