Page 1
Please refer to the MODIFICATION NOTICE. SERVICE MANUAL MODEL E2A E1C E1K EUT S-102 DVD HOME ENTERTAINMENT SYSTEM HOME ENTERTAINMENT SYSTEM (S-102) consists of DVD SURROUND RECEIVER (ADV-S102), SUB WOOFER (DSW-S102) and SPEAKER SYSTEM (SC-S102) 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に...
Page 2
S-102 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
S-102 WIRE ARRANGEMENT ワイヤー整形図 調整や部品の交換等により、ワイヤー類の結束をはずしたり移 If wire bundles are untied or moved to perform adjustment or 動させた場合には、それらの作業が完了した時点でワイヤーの parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. 整形をおこなってください。正しく整形されてないとノイズ発 Otherwise, incorrect arrangement can be a cause of noise 生の原因となることがあります。...
Page 7
S-102 2. DSW-S102 2. DSW-S102 ① Fasten the CX041 4P connector cord to the chassis with a ① CX041 4P コネクターコードをクランプバンドでシャーシ に固定。 clamp band. ② CX041 4P コネクターコードと CX081 8P コネクターコー ② Fasten the CX041 4P connector cord and CX081 8P con- ドをクランプバンドでシャーシに固定。...
Page 8
S-102 DISASSEMBLY 各部のはずしかた (組み立てるときは、逆の順序でおこなってください。 ) (Follow the procedure below in reverse order when reassembling.) ● ADV-S102 ● ADV-S102 1. ローダーパネルのはずしかた 1. Loader Panel (1) 電源を入れ「 (OPEN/CLOSE)」ボタンを押して、 (1) Switch on, and press [ (OPEN/CLOSE)] button ディスクトレイを開きます。 to open the Disc tray.
Page 9
S-102 3. Top Cover 3. トップカバーのはずしかた (1) トップカバーを止めているネジ 9 本をはずし、 (1) Remove 9 screws, then detach Top Cover. トップカバーを矢印の方向へはずします。 4. DVD Mecha. Unit 4. DVD メカユニットのはずしかた (1) Remove 4 screws fixing the DVD Mecha. (1) メカユニットを止めているネジ 4 本をはずしま す。 (2) Detach the DVD Mecha. to the arrow direction.
Page 10
S-102 5. Front Panel Ass’y 5. フロントパネルのはずしかた (1) フロントパネルからの基板とシャーシを止めてい (1) Remove 6 Front panel screws, then detach P.W.B. るネジを 6 本はずします。 and chassis. (2) Remove 4 Front panel side screws, then detach the (2) フロントパネル側面を止めているネジ 4 本(左右 各 2 本)をはずし、フロントパネルをはずしま...
S-102 DIAGNOSTICS OF OPTICAL PICKUP 光ピックアップの故障診断とトラバース ユニットの交換 AND REPLACING TRAVERSE UNIT Make failure diagnostics of the Optical Pickup as follows. 次の順序で故障診断を行ってください。 レーザー駆動電流 Iop 値が初期値の 1.5 倍以上になっている If the laser drive current (Iop) becomes more than 1.5 times of 場合は光ピックアップ交換の目安となります。 the initial value, the Optical Pickup should be replaced.
Page 13
S-102 1. Iop checked Method 1. Iop 値の確認方法 Select the laser ON/OFF (CD/DVD) mode of the test mode, レーザー駆動電流を確認する場合は、テストモードのレー and check the lop value of DVD laser or CD laser. ザー ON/OFF (CD/DVD) モードを選択して、DVD レーザー (See page 13 for test mode.) または...
Page 14
S-102 4. Rewriting the default value of the laser 4. レーザー電流初期値の書き換え方法 current レーザー電流の初期値を書き換えるには、CD または DVD レーザー電流が表示されている時に ボタンを5秒以上押 To rewrite the default value of the laser current, press the し、次に ボタンまたは ボタンを押して T23 を button for at least 5 seconds while the CD or DVD laser 選択します。...
Page 15
S-102 トラバースユニットの交換方法 3. トラバースユニットのはずしかた HOW TO REPLACE TRAVERSE UNIT 3. Traverse Unit disassembly (1) Remove 24P FFC, 15P FFC and 5P PH WIRE connect- (1) メイン基板に接続している 24P FFC、15P FFC、5P PH Caution: The optical pickup can be damaged easily by 注意 : 光ピックアップは、人体に帯電した静電気等で静電...
S-102 SERVICE MODE サービスモードについて 1. Aging Mode 1. エージングモード 1.1. Preparation 1.1. 準備 (1) Equipment used: Any one of DVD Karaoke Disc (containing more than 10 titles). (1) 使用機器:DVD カラオケディスク (10 タイトル以上のもの) (ex : Heat run disc TDV-HR01) (例:ヒートランディスク TDV-HR01)...
Page 17
S-102 2. Initial Setting Mode 2. イニシャルモード 2.1. Preparation 2.1. 準備 (1) Equipment used: None (1) 使用機器:無 (2) Unit setting: No spec other than the following procedure. (2) 本体設定:下記手順以外規定無。 2.2. Procedure 2.2. 手順 ● SYSTEM ● システム ※ This initializes the data for the function, volume, DVD mechanism, etc.
Page 18
S-102 4. テストモード 4. Test mode 4.1. Entering the test mode 4.1. テストモードの設定 To enter the test mode, press the buttons simultaneously while in the Aging mode. Not insert the disc. テストモードの設定はエージングモード時に ボタンと ボタンを同時に押すことでおこなう。ディスクは挿入していな (The Aging mode is entered by pressing the buttons simultaneously to turn on the AC power.
Page 19
S-102 4.3. モードの確定 4.3. Setting the mode With the mode selected, press the button to set that mode. モードを選択してある状態で ボタンを押すとモードを確定する。 ① In the laser on/off (CD/DVD) mode, laser on/off control is executed and the laser current is displayed. ①レーザー ON/OFF(CD/DVD) モードの場合、レーザーの ON/OFF 制御を実行し、レーザー電流を表示する。CD/DVD の切り替...
Page 20
S-102 4.4. モード内での変更 4.4. Change within the mode Changes within modes are made by pressing the buttons while the mode is set. モードを確定してある状態で ボタンまたは ボタンを押すとモード内での変更をおこなう。 ① In the laser on/off (CD/DVD) mode, laser on/off control is executed and the laser current is displayed.
Page 21
S-102 4.5. トレースモード ( エラーレート表示 ) の実行 4.5. Execution of trace mode (error rate display) (See "Table 2 - Trace mode details") ( 表 2 トレースモード詳細 参照) Trace will be performed if the button is pushed after choosing operation. 動作を選択した後、...
Page 22
S-102 表 2 トレースモード詳細 Table 2: Trace mode details Contents Contents supplement YY 内容 補足説明 1 層内周の PO 誤り検出数とアドレスの表示 CD 時は無効。 A display of PO error detection number of the inner circumference It is invalid at the time of CD operation.
Page 25
S-102 1.2. ディスク読めず 1.2. No Sound,Noise generated [No Play], [00 00] 等の表示 [No Play], [00 00] displayed etc. (1) ディスク回転せず (1) CD,DVD PLAY (1) Check Soldering of P.U. ・ short-circuit? (1) P.U. の半田ショートランドを確認 Check the Emission of Pick-up. (2) Check the circumference soldering of TR603 Pick -upの発光...
Page 26
S-102 1.3. 音声出力せず、ノイズ発生 1.3. No Sound,Noise generated (1) CD,DVD 再生時 (1) CD,DVD PLAY 電源電圧確認 Check Power Supply Voltages. 1U-3836(MAIN UNIT) 半田付けを確認 1U-3836(MAIN UNIT) Check Soldering. ・ +12V_A1,-12V_A1 ・ IC602,IC603 ・ +12V_A1,-12V_A1 ・ IC602,IC603 ・ +7V,-7V of [IC601] ・ IC404 ・ +7V,-7V of [IC601] ・...
Page 27
S-102 CODECからAMPへのアナログ Check Analog Audio Data output オーディ オデ ータ 出力確 認 半田付けを確認 from CODEC to AMP. Check Soldering. ・ [IC501]:28,29,31pin 1U-3836(MAIN UNIT) ・ [IC501]:28,29,31pin 1U-3836(MAIN UNIT) ・ [IC501]output and [IC506],[IC507] ・ [IC506],[IC507] ・ [IC501] 出力 [IC506],[IC507]入 力: ・ [IC506],[IC507]...
Page 28
S-102 (2) アナログオーディオ入力時(AUX1,AUX2) (2) Analog audio in(AUX1,AUX2) AUX1-2からFUNC.VR.へのアナログ Check Analog Audio Data input オーディ オデ ータ入 力確 認 半田付けを確認 from AUX1-2 to FUNC.VR. Check Soldering. AUX1-2からFUNC.VR.へのアナログ Check Analog Audio Data input ・ JK601 1U-3836(MAIN UNIT) ・ JK601 1U-3836(MAIN UNIT) オーディ...
Page 29
S-102 3. 1U-3836-1 (MAIN UNIT) 3. 1U-3836-1 (MAIN UNIT) 3. 1U-3836-1 (MAIN UNIT) 3. 1U-3836-1 (MAIN UNIT) 3-1.DVD 再生時 3-1.DVD PLAY 3-1.DVD 再生時 3-1.DVD PLAY (1) インターレース映像出力せず (1) INTERLACE output does not outputed. (1) インターレース映像出力せず (1) INTERLACE output does not outputed.
Page 30
S-102 Check analog signal for Video Check Soldering. ENCODERからビデオドライバーへのアナログ 半田付けを確認 from ENCODER to Video driver(COMPONENT) ・ [IC801]37-39pin 映像データ出力の確認(COMPONENT) ・ [IC801]37-39pin 1U-3836-1(MAIN UNIT) ・ VR803-805 1U-3836-1(MAIN UNIT) ・ VR803-805 ・ [IC801]output and [IC802]input: ・ TR803-805 ・ [IC801]出力/[IC802]入力: ・ TR803-805 [Py],[Pb],[Pr] ・ [IC802]11,13,15pin [Py],[Pb],[Pr] ・...
Page 31
S-102 (2) プログレッシブ映像出力せず (2) PROGRESSIVE output does not outputed. B/EからI/Pへのデジタル映像データ出力 Check Digital signal for Video の確認 半田付けを確認 from B/E to I/P Check Soldering. B/EからI/Pへのデジタル映像データ出力 Check Digital signal for Video ・ [IC101]106-119pin 1U-3836-1(MAIN UNIT) ・ [IC101]106-119pin 1U-3836-1(MAIN UNIT) の確認 半田付けを確認 from B/E to I/P Check Soldering.
Page 32
S-102 (3) HDMI映像出力せず (3) HDMI映像出力せず (3) HDMI output does not outputed. (3) HDMI output does not outputed. 電源電圧確認 Check Power Supply Voltages. 電源電圧確認 Check Power Supply Voltages. 1U-3836-1(MAIN UNIT) 半田付けを確認 1U-3836-1(MAIN UNIT) Check Soldering. 1U-3836-1(MAIN UNIT) 半田付けを確認 1U-3836-1(MAIN UNIT) Check Soldering.
Page 33
S-102 3-2.外部入力時 3-2.AUX IN (1) Conposite INPUT (1) コンポジット入力 Check Power Supply Voltages. Check Soldering. 電源電圧確認 半田付けを確認 1U-3836-1(MAIN UNIT) ・ CX142 1U-3836-1(MAIN UNIT) ・ CX142 ・ ±5V_V1 ・ ±5V_V1 O.K. O.K. Check analog signal for Video Check Soldering. コネクタからビデオセレクタへのアナログ 半田付けを確認...
Page 34
S-102 (2) S端子入力 (2) Y/C INPUT 電源電圧確認 半田付けを確認 ower upp y l Vo ltages. Check Soldering. ・ CX142 1U-3836-1(MAIN UNIT) ・ CX142 1U-3836-1(MAIN UNIT) ・ ±5V_V1 ・ ±5V_V1 O.K. O.K. コ ネクタからビデオセレクタへのア ナログ 半田付けを確認 Check analog signal for Video Check Soldering.
Page 35
S-102 ● DSW-S102 ● DSW-S102 1. 1U-3811 (D.AMP/SMPS UNIT) 1. 1U-3811 (D.AMP/SMPS UNIT) (1) AMPLIFER (1) アンプ Check the following parts (and surrounding area) and 以下部品(周辺)の状態・半田付けチェック リセット信号の確認 Check Reset signal. their soldering. ・ [IC208] (BD4730) N.G. ・ (IC208 4pin) N.G. (IC208 4pin) •...
Page 38
S-102 Check the following parts (and surrounding area) and 以下部品(周辺)の状態・半田付けチェック Check +12V_A Output their soldering. ・ [T401] (SW_TRANS) +12V_A 出力電圧は正常か? N.G. • Voltage Check • [T401] (SW_TRANS) ・ [IC403] (KIA7812API) N.G. ・ (IC403 O 端子 ( 出力端子 )) ・ [D418] RN-1Z +12V_A DC (non-switched) Voltage is O.K.?
S-102 ELECTRICAL ADJUSTMENT FOR VIDEO ビデオ回路の調整 1. セッティング手順 1. SETTING (1) セットの VIDEO OUT 端子にテレビモニターを接続する。 (1) Connect the monitor TV to the video output terminal. (2) Connect the oscilloscope to the Y-signal and C-signal of (2) セットの S2 VIDEO OUT 端子から Y 信号と C 信号をそ...
Page 40
S-102 3. PROCEDURE 3. 手順 (1) セットの S2 VIDEO OUT の信号レベルをオシロスコープ (1) Adjust the signal of S-VIDEO out by the wave of oscillo- scope. 上の波高値で調整する。 (a) Y 信号レベル (a) Target, Y-signal 調整個所 :VR801 Point VR801 1000 ± 20mV Adjustment Value 調整値...
Page 41
S-102 (c) P 信号レベル (c) Target, P -signal 調整個所 :VR805 Point VR805 700 ± 10mV Check Value 調整値 : 700 ± 10mV Waveform 波形 信号レベル -signal...
Page 47
S-102 Name Pin Numbers Definition TSD0 Audio transmit serial data output 0. SEL_PLL0 Refer to the description and matrix for SEL_PLL2 pin 32. TSD1 Audio transmit serial data output 1. SEL_PLL1 Refer to the description and matrix for SEL_PLL2 pin 32.
Page 48
S-102 Name Pin Numbers Definition DCLK Clock input to PLL; (5V tolerant input). UDAC Video DAC output. F DAC V DAC Y DAC C DAC U DAC Value (pin 115) (pin 114) (pin 113) (pin 108) (pin 106) CVBS/Chroma CVBS1...
Page 49
S-102 Name Pin Numbers Definition ADVEE Analog power for video DAC. ADVSS Analog ground for video DAC. YDAC Video DAC output. Refer to description and matrix for UDAC pin 106. YUV5 YUV pixel 5 output data PIXOUT5 CCIR656 output pixel 5.
Page 50
S-102 Name Pin Numbers Definition Host data bus line; (5V tolerant input). DCI_FDS# DVD input sector start; (5V tolerant input). AUX2[0] Aux2 data I/O; (5V tolerant input). VFD_CLK VFD clock input. Host data bus line; (5V tolerant input). AUX2[1] Aux2 data I/O; (5V tolerant input).
Page 51
S-102 Name Pin Numbers Definition HWR# Host write. DCI_CLK DVD channel data clock; (5V tolerant input). AUX4[5] Aux4 data I/O; (5V tolerant input). HRD# Host read. DCI_ACK# DVD channel data valid; (5V tolerant input). AUX4[6] Aux4 data I/O; (5V tolerant input).
Page 53
S-102 M30627FHPGP (IC301: 1U-3836) Port Port Port Name Explanation Function setting VREF VREF Reference Voltage Input for A/D converter AVCC AVCC Positive power P97/SIN4 DSP_MISO Serial Data input from DSP P96/SOUT4 DSP_MOSI Serial Data output to DSP P95/CLK4 DSP_CK Serial Clock output to DSP...
Page 54
S-102 Port Port Port Name Explanation Function setting P_DOWN( 50/60Hz ) 50Hz/60Hz AC input PWB_CHK Checking PWB input /SMONI_SELB SelecteYC Video outputB /SMONI_SELA Selecte YC Video outputA VOL_B VOL encoder Pulse-B input VOL_A VOL encoder Pulse-A input P73/CTS2 NC(L:Output) Not Used:N.C.
Page 55
S-102 Port Port Port Name Explanation Function setting P123 SAN_MOSI Serial Data output to TUNER/RDS IC P122 /CODEC_RST Reset output to CODEC P121 PRE_MUTE_SUB MUTE output to PRE OUT. H:MUTE P120 HP_MUTE_SUB MUTE output to HEAD PHONE output. H:MUTE VCC2...
S-102 W9864G2GH-7 (IC402: 1U-3836) PIN DESCRIPTION PIN NAME FUNCTION DESCRIPTION Address Multiplexed pins for row and column address. A0−A10 Row address: A0−A10. Column address: A0−A7. A10 is sampled during a precharge command to determine if all banks are to be precharged or bank selected by BS0, BS1.
S-102 K4S641632 (IC103: 1U-3836) DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 LDQM N.C/RFU UDQM A10/AP 54Pin TSOP (II) (400mil x 875mil) (0.8 mm Pin pitch) PIN FUNCTION DESCRIPTION Name Input Function System clock Active on the positive going edge to sample all inputs.
S-102 BU2360FV (IC109: 1U-3836) BD7820 (IC111, IC707: 1U-3836) BLOCK DIAGRAM GND (FIN) P in N o . Pin N a me V r e f C TL Driver Vc c N . C . OU T AD J F IN...
S-102 NOTE FOR PARTS LIST 部品表について Parts for which "nsp" is indicated on this table cannot be supplied. 1.部品表に "nsp" と記載されている部品は供給できません。 When ordering of part, clearly indicate "1" and "I" (i) to avoid mis- 2.部品を発注する際は特に数字の " 1 " と英字の "I" との区別をはっき...
S-102 PARTS LIST OF P.W.B. UNIT * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
S-102 EXPLODED VIEW 30-1 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
S-102 PARTS LIST OF EXPLODED VIEW * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に "nsp" と記載されている基板 ASS’Y は供給できません。基板 ASS’Y の修理の際には基板部品表を確認のうえ、交換部品を発注してください。 * P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts.
Page 94
S-102 Ref. No. Part No. Part Name Remarks Q'ty New 00D 146 2504 004 SIDE PANEL(L) 00D 146 2505 003 SIDE PANEL(R) 00D 146 2492 019 LOADER PANEL CARD SPACER 00D 112 1000 001 VOLUME KNOB 00D 342 0040 003 FERRITE CRAMP081610N ★ 38...
S-102 EXPLODED VIEW OF DVD MECHANISM UNIT WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
S-102 PARTS LIST OF DVD MECHANISM UNIT * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
S-102 POINTS OF GREASING With Cemedine 575, glue 3 joint parts of Clamper-L and H hooks. (0.05mg each x 3) *As for greasing to the R rail groove and groove's side edge, apply grease to the outer face "intentionally". (Not only running a brush into the groove, use it with pressing to the outer face consciously.)
S-102 DSW-S102 EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
S-102 DSW-S102 PARTS LIST OF EXPLODED VIEW * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に "nsp" と記載されている基板 ASS’Y は供給できません。基板 ASS’Y の修理の際には基板部品表を確認のうえ、交換部品を発注してください。 * P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts.
Page 100
S-102 Ref. No. Part No. Part Name Remarks Q'ty New screws 0RD 473 3809 011 4X25 CBTS (1) 3X6 CBTS(S)-Z 3X6 CBTS(S)-B 3X8 CBTS (S)-B 3X10 CBTS (P)-Z 3X12 CBTS (P)-B 00D 477 0064 107 FIXING SCREW ★ 108 HEXAGON HEAD SCREW SET...
S-102 SC-S102 PARTS LIST OF EXPLODED VIEW SC-S102 PARTS LIST OF EXPLODED VIEW Ref. No. Part No. Part Name Remarks Q'ty 00D 9H3 0001 727 SPEAKER SYSTEM(L&R)
S-102 PARTS LIST OF PACKING & ACCESSORIES * 本表に "nsp" と記載されている部品は供給できません。 * Parts for which "nsp" is indicated on this table cannot be supplied. * 本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 * The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
S-102 WIRING DIAGRAMS ADV-S102 H/P JACK Portable IN JACK S102 WIRING DIAGRAM 1U-3831 FL Display 1U-3831 HP UNIT AUX IN UNIT 1U-3831 1U-3831 1U-3831 DISPLAY Left 5P SAN CW052 DISPLAY Right UNIT DISPLAY Center UNIT UNIT 5P SAN CW051 CY211(21P FFC)
S-102 MEASURING METHOD AND WAVEFORMS 各部の波形と測定方法 To check the waveforms on the FEP, the GND (-) probe of FEP 基板の波形チェックを行うためにはオシロスコープの the oscilloscope to “VHALF” point. GND(-) プローブを "VHALF" ポイントに接続します。 (Except for lnner SW, TRVSW) 注 意 NOTES 測定ディスク: DVD/VT502 or TDV-520A...
Page 107
S-102 WAVEFORMS IU-3807 FEP Unit. DVD PLAY Disc : TDV-520A CD PLAY Disc : TCD-784 RF waveform RF waveform ①ARF ①ARF ②NARF ②NARF RANGE .2 v .05 sec RANGE .2 v .2 sec DVD LOADING PLAY CD LOADING PLAY ③FODRV ③FODRV...
S-102 NOTE FOR SCHEMATIC DIAGRAM 配線図について ! 印の部品は安全を維持するために重要な部品です。 WARNING: 従って交換時は必ず指定の部品を使用してください。 Parts marked with this symbol ! have critical characteristics. Use ONLY replacement parts recommended by the manufactur- 注) (1) 指定なき抵抗値は Ω、k は kΩ、M は MΩ を示す。 CAUTION: Before returning the unit to the customer, make sure you make (2) 指定なきコンデンサーの値は...
Page 110
SCHEMATIC DIAGRAMS (2/17) S-102 AUDIO SIGNAL LINE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (2/17) 1U-3836-1 MAIN UNIT (1/8) (B / E BLOCK)
Page 111
SCHEMATIC DIAGRAMS (3/17) S-102 AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (3/17) 1U-3836-1 MAIN UNIT (2/8) (I / F BLOCK)
Page 112
SCHEMATIC DIAGRAMS (4/17) S-102 SCHEMATIC DIAGRAMS (4/17) 1U-3836-1 MAIN UNIT (3/8) (uCOM BLOCK)
Page 113
SCHEMATIC DIAGRAMS (5/17) S-102 AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (5/17) 1U-3836-1 MAIN UNIT (4/8) (AUDIO DSP BLOCK)
Page 114
SCHEMATIC DIAGRAMS (6/17) S-102 AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (6/17) 1U-3836-1 MAIN UNIT (5/8) (CODEC / DIR BLOCK)
Page 115
SCHEMATIC DIAGRAMS (7/17) S-102 AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (7/17) 1U-3836-1 MAIN UNIT (6/8) (FUNCTION / VOLUME BLOCK)
Page 116
SCHEMATIC DIAGRAMS (8/17) S-102 VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (8/17) 1U-3836-1 MAIN UNIT (7/8) (IP / HDMI / PLD BLOCK)
Page 117
SCHEMATIC DIAGRAMS (9/17) S-102 VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (9/17) 1U-3836-1 MAIN UNIT(8/8) VIDEO ENCODER / IN-OUT BLOCK...
Page 118
SCHEMATIC DIAGRAMS (10/17) S-102 AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (10/17) 1U-3831-4 LOCAL POWER UNIT...
Page 119
SCHEMATIC DIAGRAMS (11/17) S-102 AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (11/17) 1U-3831-1 DISPLAY CENTER UNIT 1U-3831-2 DISPLAY RIGHT UNIT 1U-3831-3 DISPLAY LEFT UNIT 1U-3831-5 HP OUT UNIT 1U-3831-6 AUX IN UNIT 1U-3831-7 IF-1 UNIT...
Page 120
SCHEMATIC DIAGRAMS (12/17) S-102 AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (12/17) 1U-3811-3 I/F UNIT 1U-3811-4 AC I/F UNIT...
Page 121
SCHEMATIC DIAGRAMS (13/17) S-102 AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (13/17) 1U-3811-1 D.AMP/SMPS UNIT (1/3)
Page 122
SCHEMATIC DIAGRAMS (14/17) S-102 AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (14/17) 1U-3811-1 D.AMP/SMPS UNIT (2/3)
Need help?
Do you have a question about the S-102 and is the answer not in the manual?
Questions and answers