TABLE OF CONTENTS 1 – INTRODUCTION About this Manual ..........................1-1 Safety Messages Used in this Manual ....................1-1 Pre-Delivery Inspection ........................1-2 Front Axle Tire Alignment ....................... 1-2 Service and Assistance ........................1-2 Reporting Safety Defects ........................1-2 Occupant and Cargo Carrying Capacity Label ................. 1-3 Vehicle Certification Label .......................
Page 4
Table Of Contents Power Sunvisor ..........................3-4 Hazard Warning Flashers ........................3-4 Air Conditioner/Heater – Automotive (Dash) .................. 3-5 Radio In-Dash/Rearview Monitor System ..................3-5 Infotainment Center/GPS ........................3-7 Battery Boost Switch ........................3-8 Engine Cooling System ........................3-9 Fuel Fill Access ..........................3-9 Diesel Exhaust Fluid Fill ........................
Page 5
Table Of Contents Electrical Generator – 120-Volt ......................6-6 Electrical System – House 12-Volt DC .................... 6-8 House/Coach Battery Disconnect Switch ..................6-9 Battery Access ..........................6-9 Battery Care ............................ 6-10 Circuit Breakers and Fuses – House 12-Volt DC ................6-12 7 –...
The instructions included in this manual are intended as a guide, and in no way DANGER indicates a hazardous situation extend the responsibilities of Winnebago which, if not avoided, will result in death or Industries beyond the standard written serious personal injury.
National Highway Traffic Safety Administration delivery inspection of the chassis and all (NHTSA) in addition to notifying Winnebago motorhome components. Industries, Inc. As a part of the pre-delivery inspection...
SECTION 1 – INTRODUCTION or go to their website at http://www.safercar.gov or write to: Administrator, NHTSA 1200 New Jersey Avenue S.E. Washington, D.C. 20590 You can also obtain other information about motor vehicle safety from the NHTSA website at http://www.safercar.gov OCCUPANT AND CARGO CARRYING CAPACITY LABEL This label is affixed in the driver’s area next to...
These pressure levels must be maintained to assure proper handling, safety, 2. Chassis manufacture date. and fuel economy. 3. Month and year of manufacture at Winnebago ® 9. Rear Axle Wheel Configuration: Single or Industries Dual as it relates to the inflation.
(26.4 gal.) Notes: All information is based upon the most recent data available. Visit the Winnebago Industries, Inc. web page – www.winnebagoind.com – for the most current product information. The height of each model is measured to the top of the tallest standard feature and is based on the curb weight of a typically equipped unit.
Motorhome Serial Number ___________________________________________________________ Chassis Vehicle Identification No. (VIN) ________________________________________________ Vehicle Mileage at Delivery __________________________________________________________ Selling Dealer Name ________________________________________________________________ Address __________________________________________________________________________ __________________________________________________________________________ ® YOUR WINNEBAGO INDUSTRIES DEALER /SERVICE CENTER Name ____________________________________________________________________________ Address __________________________________________________________________________ __________________________________________________________________________ Contact ____________________________________________Phone ________________________ CHASSIS SERVICE CENTER...
SECTION 2 – SAFETY AND PRECAUTIONS GENERAL WARNINGS DRIVING SAFETY • Only seats equipped with seat belts are to be occupied while the vehicle is moving. WA RNING • Make sure all passengers have seat belts fastened. Lap belts should fit low on the hips and upper thighs.
SECTION 2 – SAFETY AND PRECAUTIONS • Do not adjust tilt steering in a moving vehicle. • Do not operate the cruise control on icy or WA RNING extremely wet roads, winding roads, in heavy traffic, or in any other traffic situation where a constant speed cannot be maintained.
SECTION 2 – SAFETY AND PRECAUTIONS • Open doors and other ventilating openings. • Leave the area until odor clears. DANGER • Have the propane system checked and leakage source corrected before using again. Do not use gas cooking appliances for Failure to comply could result in death or comfort heating.
It will detect CO gas from any combustion ® Winnebago Industries dealer. source such as the furnace, gas range/oven, water heater, refrigerator, chassis engine, and electric Further Information generator engine.
RV application. We that is also listed for RV application. We recommend obtaining a replacement from your recommend obtaining a replacement from your ® ® Winnebago Industries dealer. Winnebago Industries dealer. Further Information Further Information Please read the information provided by the See the manufacturer’s information in your...
SECTION 2 – SAFETY AND PRECAUTIONS To use a slider windows as an exit, first slide the window open, then either slide the screen open or push the screen material out, depending on window construction. Escape Window Escape Window (Optional) (Pull both latch handles inward and -If Equipped push window open)
SECTION 2 – SAFETY AND PRECAUTIONS FORMALDEHYDE INFORMATION Side Latch Some of the materials used in this recreational vehicle emit formaldehyde. Eye, nose, and throat irritation, headache, nausea, and a variety of asthma-like symptoms, including shortness of breath have been reported as a result of Bottom formaldehyde exposure.
If Mold Is Present, What Will Mold is a plant and requires its own special environment to grow. That environment includes ® Winnebago Industries organic materials, nutrients, moisture, and proper If Winnebago Industries determines that mold temperature. ® ® is present in the Winnebago /Itasca...
Do not worry about damaging the proper towing equipment to use. tire or wheel rim by driving on it. A tire or ® Winnebago Industries does not assume wheel replacement is cheaper than damaging responsibility for damage incurred while towing the vehicle or injuring yourself.
SECTION 2 – SAFETY AND PRECAUTIONS Steel Wheels • The lug nut for steel wheels is a non-plated, hat-shaped, flange nut. The accompanying dome-shaped, split cone washer should be positioned ‘dome first’ onto the wheel stud before the nut as shown. The wheel on your coach has a push on liner which is removed similar to a hubcap.
SECTION 2 – SAFETY AND PRECAUTIONS When installing the liner, be sure it is engaged all around the perimeter (outside edge) equally. Valve Stem Note: If the edge on one side is pushed in before the other, it may be difficult to complete the push on procedure.
SECTION 2 – SAFETY AND PRECAUTIONS • Before removing lug nuts, remove the push on nut covers. To make the removal process less NOTICE challenging, it is recommended that you wrap each individual jaw of pliers with electrical tape or use a commercial lug nut cover Do not attempt to push start this vehicle.
The information in this section refers only to features installed or adapted to the dash and 1- Insert tab into buckle slot until it “clicks” and is driver compartment area by Winnebago locked ® Industries . It also includes passenger seating in the living area of the coach.
SECTION 3 – DRIVING YOUR MOTORHOME Lap/Shoulder Belts CHILD RESTRAINTS Fastening -If Equipped Hold the belt just behind the tongue. Next, A properly installed and secured child bring the belt across the body and insert the restraint system can help reduce the chance or tongue into the buckle until the latch engages.
SECTION 3 – DRIVING YOUR MOTORHOME in your InfoCase. In case keys are lost or stolen, Tether Anchor Loop your dealer or a locksmith can provide you with duplicate keys or modify the locks. REMOTE KEYLESS ENTRY The main entry door on your vehicle is equipped with a Remote Keyless Entry system.
SECTION 3 – DRIVING YOUR MOTORHOME Mirror Heaters POWER SUNVISOR The mirrors may also contain heating elements to de-fog or de-ice the mirror glass -If Equipped during cold weather operation. A switch for the The Power Sunvisor is controlled by a switch mirror heaters is located on the dash.
SECTION 3 – DRIVING YOUR MOTORHOME AIR CONDITIONER/HEATER – AUTOMOTIVE (DASH) See the chassis manual provided in your InfoCase for specific recommendations, operating instructions, and maintenance information. NOTE: The dash air conditioner is not designed to cool the entire interior of the coach, but is intended only to provide cooling for the cab area.
Page 32
SECTION 3 – DRIVING YOUR MOTORHOME This system is also featured with a rearview camera view on the monitor until the turn is camera monitor system, which lets you see what completed or the signal lever is canceled is directly behind your coach for safety and manually.
SECTION 3 – DRIVING YOUR MOTORHOME ® Radio Remote Control This system also features SiriusXM satellite radio, iPod/USB connections, and CD/DVD A hand-held remote control for the radio lets player. you control the radio from a distance for your convenience. The remote control is included in NOTE: As a safety feature, this system will not your InfoCase.
SECTION 3 – DRIVING YOUR MOTORHOME camera view on the monitor until the turn is NOTE:The House/Coach Battery Disconnect completed or the signal lever is canceled switch must be ON while listening to the manually. dash radio because the audio relay is powered by house batteries.
SECTION 3 – DRIVING YOUR MOTORHOME Battery Boost Switch (Located on lower dash area) • Press and Hold in the ON position while turning ignition key for emergency starting power. ENGINE COOLING SYSTEM Do not remove the radiator cap while engine and radiator are still hot.
SECTION 3 – DRIVING YOUR MOTORHOME VALVE STEM ACCESS ® (Mercedes-Benz Sprinter Chassis) Front Wheel Valve Stem Access on 18-Hole Steel Wheel with Push-On Full Wheel Trim –If Equipped 1. Obtain a double angle push/pull truck tire gauge. Diesel Exhaust Fluid Fill (Located under front hood) -Typical installation shown Further Information...
Page 37
SECTION 3 – DRIVING YOUR MOTORHOME Inner rear dual Hose extension 4. Using the hose extension as a remote handle, 6. When tire pressure testing is complete, unscrew the valve stem cap (retaining cap in reinstall the valve stem cap (with the cap still the end of the hose extension).
SECTION 3 – DRIVING YOUR MOTORHOME end, remove valve stem cap, insert valve stem extension into hose extension, and reinstall valve stem extension onto valve stem until snug. Pull off hose extension and re-insert valve stem cap into end of hose. 5.
Page 39
SECTION 3 – DRIVING YOUR MOTORHOME dealership. However, alignment should be checked and adjusted after you have fully loaded the motorhome according to your personal needs. Thereafter, the alignment should be periodically inspected to help prevent uneven tire wear. Any excessive or abnormal tire wear may indicate worn or misaligned suspension or steering, unbalanced tire, or other tire/suspension problem.
SECTION 4 – APPLIANCES AND SYSTEMS The appliances installed in your motorhome are manufactured by reputable RV appliance makers and have been tested by independent laboratories to meet all applicable standards and codes set for RV appliances. See Section 2 - Safety and Precautions of this manual for any safety and precautions you need to take regarding the operation of your appliances.
SECTION 4 – APPLIANCES AND SYSTEMS Basic Operation Further Information For further information and operating cautions, see the refrigerator operating instructions included in your InfoCase. REFRIGERATOR SERVICE ACCESS COMPARTMENT (Exterior) • ON/OFF Switch The exterior refrigerator service compartment allows access to the rear of the refrigerator for inspection, maintenance, and service.
SECTION 4 – APPLIANCES AND SYSTEMS DAN GE R Do not use gas cooking appliances for comfort heating. May lead to carbon monoxide poisoning, which can lead to death or serious injury. Refrigerator Access Compartment *Shown with cover removed WARNING -Typical View Gas cooking appliances need fresh air for RANGE TOP...
SECTION 4 – APPLIANCES AND SYSTEMS Further Information See the manufacturer’s user guide provided in NOTICE your InfoCase for instructions on replacement of light bulbs and replacement or cleaning of grease filter elements. Turn off the range and allow it to cool before closing the range cover.
SECTION 4 – APPLIANCES AND SYSTEMS Tank Levels Switch Battery Levels Switch The approximate fluid levels are measured by To get an accurate reading: electronic sensors on the sides of the tanks. Tank • Both the chassis engine and the generator levels are displayed as 1/3, 2/3, and Full (F).
SECTION 4 – APPLIANCES AND SYSTEMS “Water Heat LP Fail”, it means that the burner has gone into “lockout” mode and must be restarted. If this happens, turn the Water Heater LP switch off for about 5 minutes, then turn it back on.
SECTION 4 – APPLIANCES AND SYSTEMS Further Information See the Water Heater manufacturer’s operation manual provided in your InfoCase for complete operating instructions, safety warnings, and maintenance information. WATER HEATER - GAS TANKLESS - MODEL 25P The Gas Water Heater operates from propane gas.
SECTION 4 – APPLIANCES AND SYSTEMS Modulating Dial “clockwise” to increase the flame/BTUs to raise the Hot Water CAUTION Temperature. Note: Use caution not to increase the Dial too much which could cause the Hot Water Hot water can escape from tank causing Temperature to rise to the point the injury.
SECTION 4 – APPLIANCES AND SYSTEMS 3. Pull the handle of the P-T valve straight out PRESSURE-TEMPERATURE and allow water to flow until it stops. RELIEF VALVE (TANKLESS WATER HEATER) On occasion, water may be seen seeping from the water heater pressure temperature relief valve.
SECTION 4 – APPLIANCES AND SYSTEMS To Shut Down • Slide Thermostat switch to the OFF position. • Turn OFF Propane Gas Tank switch if coach will be stored for a period of time. Further Information Refer to the manufacturer’s user guide provided in your InfoCase for further information, including operating precautions, and periodic maintenance.
SECTION 4 – APPLIANCES AND SYSTEMS To Operate the Heat Pump many vents are closed, however, it can cause the air conditioner unit to shut Refer to the manufacturer’s user guide down, particularly in high humidity provided in your InfoCase for complete operating conditions.
SECTION 5 – PROPANE GAS PROPANE GAS SUPPLY WARNING The propane gas system supplies fuel for the gas range/oven, water heater, furnace, and refrigerator (while in gas mode). When used and Do not alter or remove propane tank handled properly, this system is safe and valves or gauge.
Page 54
SECTION 5 – PROPANE GAS WARNING Do not fill propane container(s) to more than 80 percent of capacity. A properly filled container contains approximately 80 percent of its volume as liquid propane. Overfilling the propane container(s) can result in uncontrolled propane flow, which could lead to a fire or explosion and result in death or serious injury.
SECTION 5 – PROPANE GAS propane gas outlets in the United States do not Here are a few precautions to observe that will offer any other type of liquefied petroleum gas help you to use the propane gas system safely: than propane to the general public.) Check local •...
SECTION 5 – PROPANE GAS water heater. They contain carbon monoxide, PROPANE GAS WARNINGS which is an odorless, colorless, and poisonous AND PRECAUTIONS gas. It is illegal for vehicles equipped with propane tanks to travel on certain roadways or through WARNING certain tunnels in the U.S.
SECTION 5 – PROPANE GAS Only your dealer or a qualified propane gas service should remove the regulator cover for adjustments. WARNING Visually inspect the pressure regulator vent periodically for blockage by accumulated debris or insect nests, etc. Vent obstruction could result in excessive pressure causing fire or explosion, which could result in death or serious injury.
Page 58
SECTION 5 – PROPANE GAS This means that in extremely cold weather when a large volume of gas is being used by the furnace for heating, it is possible to experience a loss of gas pressure. At first, this problem may appear to be caused by an empty tank or a regulator freeze-up, but is actually caused by failure of the liquid gas to vaporize as fast as it is needed by the furnace.
SECTION 6 – ELECTRICAL Your coach is equipped with an electrical the power converter automatically changes a system consisting of two separate voltages: portion of the 120-volt current to 12-volt DC current. All equipment in the motorhome that is • 12-volt DC system (battery current);...
Page 60
SECTION 6 – ELECTRICAL 30 Amp Receptacle WARNING • Swivel the small cover section upward to access the cord passage. This connection is for 110/125 Volt AC, 60 Hz 30 Ampere supply. Do not exceed circuit rating. Exceeding the circuit rating may cause a fire and result in death or serious injury.
SECTION 6 – ELECTRICAL Park Fuses or Breakers Most campgrounds are equipped with a fuse or circuit breaker at the receptacle (which we recommend shutting off before engaging or disengaging the power cord.) This protects the park’s wiring, as well as the power cord on your vehicle from electrical damage.
SECTION 6 – ELECTRICAL POWER CENTER NOTICE (Converter) The power converter is generally located in a lower cabinet face in the galley or living area, Do not store items too closely around the depending on the floorplan of your model. inverter unit in the storage compartment.
SECTION 6 – ELECTRICAL reset, take immediate steps to correct the cause of overheating. A portion of the house 12-volt load NOTICE (lights or motors or both) should be turned off to reduce total load. Also, inspect the power converter to make sure ventilation is not Do not block the converter cover vents in obstructed.
SECTION 6 – ELECTRICAL ELECTRICAL OUTLETS – HOUSE 120-VOLT AC WARNING A number of standard household electrical outlets are provided throughout the coach for The GFCI will not completely eliminate connecting small appliances such as televisions, the risk of electrical shock. Infants and radios, toasters, etc.
SECTION 6 – ELECTRICAL Generator Hourmeter The Generator hourmeter registers the total WARNING number of hours that the Generator has been operated. Press the GenSet Meter button once to get reading. Do not plug the power cord into the Refer to the hourmeter to determine when generator receptacle while the generator periodic maintenance is due and to record is running.
SECTION 6 – ELECTRICAL • Park the vehicle so that the wind will carry the exhaust away from the vehicle. Also, note the position of other vehicles to be sure their exhaust will not enter your vehicle. • Do not operate the Generator engine while parked if vegetation, snow, buildings, vehicles, or any other object can deflect the exhaust under or into the vehicle.
SECTION 6 – ELECTRICAL The house batteries supply power to 12-volt equipment located in the living area of the motorhome. This includes the following 12-volt powered components (if equipped): interior 12- volt lighting, range exhaust fan, propane furnace fan, fresh water pump, systems monitor panel, refrigerator, roof vent fans, and 120-volt electrical generator starter.
SECTION 6 – ELECTRICAL House Batteries Chassis Battery Connector Chassis Battery (Located to the right of the accelerator pedal) The chassis (starting) battery is located in a compartment “well” in the floor beneath carpet Further Information ahead of the driver seat. See the chassis manual provided in your InfoCase for details on access and servicing.
Page 69
SECTION 6 – ELECTRICAL The two best defenses against sulfating Further precautions are: and insufficient charge are to: • Check the state of charge periodically to avoid discharge or sulfating. 1. Turn off the House/Coach Battery Disconnect switch to avoid parasitic discharge (the trickle To ensure that the battery will always accept discharge caused by directly connected and hold a charge, follow these simple...
Chassis Battery If your coach is going to be unoccupied for ® two weeks or more, Winnebago Industries recommends disconnecting the chassis battery in your coach to avoid battery discharge. Functional Non-Functional Unplug the Chassis Battery Connector...
Page 71
SECTION 6 – ELECTRICAL Automotive Chassis and House 12-Volt Circuit Breakers (Located in passenger side compartment) * Turn latches to remove cover Automotive Chassis and House 12-Volt Circuit Breakers * Shown with cover removed 6-13...
SECTION 7 – PLUMBING FRESH WATER SYSTEM The Fresh Water System provides water to the galley sink, shower, bathroom lavatory, toilet, and water heater. Water may be supplied by either of two sources: • A fresh water tank and water pump located within the motorhome, or •...
Page 74
SECTION 7 – PLUMBING Fresh Water Valve Fresh Water Valve (Located in water service center) (Located in water service center) -Typical View -Typical View 4. Turn city water supply ON. Using City Water 5. Use the level display on the monitor panel to When connected to an outside source of water, oversee filling of the tank, or when the tank is the water bypasses the water pump and storage...
SECTION 7 – PLUMBING Using Tank Water (Gravity Fill) NOTE: Ensure the Fresh Water valve is in NORMAL position to use the water • Turn Water Pump switch ON. While the pump. If the valve is in Tank Fill position, switch is on, the water pump will the pump will run continuously without automatically supply tank water as needed.
Page 76
SECTION 7 – PLUMBING Initial Waterline Priming 1. Ensure that all water drain valves are closed, including water heater valve. 2. Turn Water Pump switch to “OFF” position. 3. Fill water tank. 4. Open all faucets, hot and cold. 5. Turn ON the Water Pump switch. 6.
SECTION 7 – PLUMBING Water Pump -Typical installation shown Cold Water Filter Assembly • Model 25P - Located beneath removable (Located below galley sink) panel in rear corner bed. NOTE: Hot waterline is not filtered. • Model 25T - Located behind removable access panel in rear driver side Replacing the Cold Water Filter compartment.
SECTION 7 – PLUMBING • Before using the water for drinking, run a few DISINFECTING YOUR FRESH gallons of water through the filter and discard WATER SYSTEM water to avoid consuming carbon dust or particles that may have been present in the ®...
SECTION 7 – PLUMBING ppm chlorine concentration should be allowed to stand in the system for at least 1 hour.) 5. Drain the water tank and refill with fresh water. 6. Open each faucet again and run fresh water to flush chlorinated water from the lines.
SECTION 7 – PLUMBING See winterizing instructions at the end of this section to prepare the toilet for storage in freezing conditions. Further Information See the toilet manufacturer’s operation information in your InfoCase for complete operating, care, and maintenance information. DRAINAGE SYSTEM (P-TRAPS) Ensure there is an adequate amount of water in the drainage system p-traps to avoid sewer odor...
SECTION 7 – PLUMBING NOTE: DO NOT OPEN BOTH VALVES AT NOTE: Always keep sewage drain outlet ONCE. Do not open the Gray Waste Tank capped while sewage connection is not in use. Drain valve until the black tank is Holding Tank Level Indicators drained and dump valve closed to avoid See “Systems Monitor Panel”...
Page 82
SECTION 7 – PLUMBING 2. Remove dust cap from sewage drain outlet and connect sewage drain hose. Be sure it is firmly attached. Waste Pump Dust Cap (Located behind removable panel in water service center) Sewage Drain Outlet -Typical View (Located in driver side compartment) -Typical View NOTE: If Waste Pump stalls, check breaker in...
SECTION 7 – PLUMBING sewage back-up into gray tank. Gray 7. Rinse sewage drain hose thoroughly with water also rinses any black water solids water and stow. from the sewage drain hose. NOTE: We recommend that you dump all 5. Open the Gray Waste Tank Drain valve holding tanks before traveling to avoid (located beneath driver side rear carrying unnecessary weight.
SECTION 7 – PLUMBING Holding Tank Heater Switch Location: The Waterline and Water Tank Drain valves are used to drain water from the water tank and • Models 25T and 25Q - Located on back of the water supply lines when preparing the bath wall near thermostat.
SECTION 7 – PLUMBING Method 1 – Blow Out Procedure WATER HEATER BYPASS AND (Drain and purge waterlines using ANTIFREEZE SIPHON VALVES compressed air) Your coach is equipped with a Water Heater 1. Level the Motorhome. If the coach is not Bypass valve and an Antifreeze Siphon level, there may be “low points”...
Page 86
SECTION 7 – PLUMBING • Twist the filter cartridge “counter- clockwise” about one-quarter turn, then pull it down and out of the filter socket. Discard used filter. Water Heater Drain Plug (Remove with socket) • Also, open the Pressure-Temperature Relief valve to prevent air locking while draining.
Page 87
A “blow-out” plug can be each drain for the galley sink, lavatory sink, ® ® and shower/tub. This fills the drain trap pipes purchased at any Winnebago or Itasca to prevent holding tank odors from entering dealer. the coach during storage.
Page 88
SECTION 7 – PLUMBING Method 2 – Remove Water Filter Antifreeze Fill Procedure 1. Remove and discard the filter cartridge from (Fill plumbing lines with RV water system the cold water filter assembly below the galley antifreeze) sink. (If your coach is not equipped with a cold water filter assembly, continue to next NOTE: As an alternative to totally draining the numbered step).
Page 89
SECTION 7 – PLUMBING 4. Turn the Winterization valve handle so it points toward the antifreeze siphon tube. This will allow the siphon tube to draw non-toxic RV antifreeze into the waterlines. (See “Water System Drain Valve Locations” chart at the end of this section for location on your model).
Page 90
SECTION 7 – PLUMBING When Done Adding RV Antifreeze 8. Turn the Water Pump switch OFF. 9. Turn the Winterization valve so it points toward the waterline connected to the water pump. This will stop the flow from the antifreeze siphon tube and revert the tank line flow to the water pump.
Page 91
SECTION 7 – PLUMBING 14. Close dump valves and refit the dust cap onto the drain outlet. This will inhibit rust formation on valve shafts and prevent entry and contamination by airborne debris, insects, and rodents. Your drainage and fresh water systems are now winterized.
SECTION 7 – PLUMBING WATER SYSTEM DRAIN VALVE LOCATIONS Model System Drain Valve Locations Waterlines • Two (2) drain valves in the water service center and two (2) drain valves located through an access hole beneath the bed. Also, place the tip of your finger inside the city water connection and gently press the backflow valve (small “button”...
SECTION 8 – ENTERTAINMENT To Extend TV TV – 12V LED • Open the wooden cabinet cover located on the -If Equipped inboard side of TV. The LED flat panel TV is powered by 12-volt DC current. The 12-volt current is supplied from the house batteries, or from the power converter when connected to shoreline power or running the generator.
SECTION 8 – ENTERTAINMENT Supplement. • The TV screen will See your InfoCase for specific operating display the DVD player guides for audio and video components. logo when the correct input is selected. DVD PLAYER WITH DELUXE Play DVD SOUND •...
SECTION 8 – ENTERTAINMENT Further Information • Signal Meter See the manufacturer’s quick reference guide • Attenuator Dial Power Switch provided in your InfoCase for complete feature descriptions and operating instructions. TV ANTENNA - DIGITAL ® (Jack Digital HDTV Over-the-Air Antenna) Your coach is featured with a digital antenna, which provides crystal clear digital HD reception...
SECTION 8 – ENTERTAINMENT TV SIGNAL AMPLIFIER The TV Signal Amplifier is built into the antenna and can be turned on or off with a power switch located on a switchplate near the entertainment center cabinet. An indicator light will illuminate when the switch is on and the signal amplifier is active.
A second connection may be included inside a cabinet in the bedroom for the rear TV (if equipped). ® See your authorized Winnebago Industries Stationary and In-Motion Satellite dealer for proper installation and sealing of roof Dish Controls mounted components.
SECTION 9 – FURNITURE AND SOFTGOODS BOOSTER SEAT CUSHION -If Equipped The driver and co-pilot seats may feature a Booster Seat Cushion which provides increased seat height and added comfort while in the lounge seating position. The Booster Seat Cushion must not be used when the vehicle is in motion.
SECTION 9 – FURNITURE AND SOFTGOODS To lower bunk for use 1. Move both the driver and passenger cab seats WARNING forward and recline completely to allow clearance for the bunk to be lowered. See “Seats - Driver/Co-Pilot” in Section 3 - Engage bunk storage latches.
SECTION 9 – FURNITURE AND SOFTGOODS COMFORT SOFA SLEEPER –If Equipped (Typical View – Your coach may differ in appearance) Your coach may be equipped with a Comfort Sofa Sleeper, which is featured with an air bed that can be adjusted to the firmness of your choice.
Page 102
SECTION 9 – FURNITURE AND SOFTGOODS 5. Turn the Comfort Adjust dial (located on the Air Bed Control) to desired firmness - Plush, Medium, or Firm. Air Bed Control (Located at head of mattress) 6. Turn the Inflate/Deflate switch “clockwise” to the INFLATE position.
SECTION 9 – FURNITURE AND SOFTGOODS Bed to Sofa 1. Turn the Comfort Adjust dial (located on the NOTICE Air Bed Control) to the OFF position (to keep the pump from automatically turning on during storage). To avoid mattress damage, fold edges back 6 inches and foot end back 20 inches before returning to sofa position.
Page 104
SECTION 9 – FURNITURE AND SOFTGOODS Dinette to Bed 1. Remove both dinette back cushions and set Table Leg aside. Catch 5. Remove the table from the wall support bracket by lifting the end of the table. Wall 2. Lift both dinette seat cushions upward. Support Table Bracket...
SECTION 9 – FURNITURE AND SOFTGOODS NOTE: The cab seats must be completely rotated (facing the lounge area) to use as dinette seating. See the Driver/Co-Pilot Seat information in Section 3 - Driving Your Motorhome for complete operating instructions. Reverse steps to convert back into dinette seating.
SECTION 9 – FURNITURE AND SOFTGOODS Reverse steps to store dinette table and pedestal leg. WINDOW SHADES/SCREENS Your coach is featured with multi-positioning window shades and screens that can be used for light filtering, outside airflow, bug protection, daytime room darkening, or nighttime privacy. •...
People are drawn to the natural beauty of and the wood is considered part of the natural ® wood. At Winnebago Industries , our craftsmen aging process and is not to be considered defect work with the art found in each piece of wood to or damage.
SECTION 10 – SLIDEOUT ROOMS Rear slideout switches (if equipped) are SLIDEOUT ROOM KEYLOCK typically located on a wall in the rear of the coach in or near the slideout room. Location varies by A Master Slideout Room Keylock is located model and floorplan.
Page 110
SECTION 10 – SLIDEOUT ROOMS To Retract Slideout Room WARNING Before Retracting! • Be sure the coach is level and the Parking Brake is set. CRUSH HAZARD. Keep people and • Ensure exterior compartment doors are closed objects clear of the inside and outside of the slideout room when operating.
SECTION 10 – SLIDEOUT ROOMS • Press the Slideout Room “RETRACT/IN” SLIDEOUT ROOM switch and hold until the room is fully TROUBLESHOOTING retracted, then release the switch. (LIPPERT) • To stop retracting the room during operation, release the button. -If Equipped •...
Page 112
SECTION 10 – SLIDEOUT ROOMS • (8) - HALL SIGNAL NOT PRESENT. • Motor • Mode Encoder is not providing a signal. This is • Status Direction Button LED’s usually a wiring problem. • (9) - HALL POWER SHORT TO GROUND.
SECTION 10 – SLIDEOUT ROOMS SLIDEOUT EMERGENCY RETRACTION (LIPPERT) -If Equipped If the slideout mechanism is malfunctioning and the room will not retract using the interior control switch or exterior control panel, you may need to access the slideout motors and manually push the room in to the travel position.
SECTION 10 – SLIDEOUT ROOMS Slideout Room Seal Care and 5. When the slideout room is fully retracted, secure the room with a support item (e.g. 2x4 Maintenance wood board) above the interior slideout room While most household cleaners work well for to secure room during travel.
• Have the sealant replaced if you notice any of attention. Delaying these repairs may allow water the above. Your local Winnebago Industries leakage and result in damage to interior ceiling dealer has the correct and necessary parts and and body panels, upholstery, etc., which is not experience to help you maintain your sealants.
SECTION 11 – MAINTENANCE AND STORAGE weight to the vehicle. This, in effect, reduces the • Do not scrape ice or snow from the painted amount of cargo you can carry and remain within surface. Brush off gently with a soft-bristled GVWR and GAWR limits.
Page 117
SECTION 11 – MAINTENANCE AND STORAGE Washing NOTE:Avoid aiming water flow from a hose or spray from high-pressure washing • Commercial vehicle wash facilities should be equipment into any appliance intake, as strictly avoided! They will scratch your RV! damage or difficulty in operating Truck-style wash centers have high- appliances may occur.
SECTION 11 – MAINTENANCE AND STORAGE Further Information • Avoid paste waxes. They sometimes have fillers and additives that give a very short term See the manufacturer’s information provided result. Stay away from silicones in polishes in your InfoCase for complete care and and soaps.
SECTION 11 – MAINTENANCE AND STORAGE EXTERIOR LIGHTS NOTICE ® Most Winnebago Industries vehicles have polycarbonate lenses on exterior lamps, which are very sensitive to a variety of chemical Do not use citrus-based cleaners on solvents and cleaners. polycarbonate finishes. Citric compounds...
SECTION 11 – MAINTENANCE AND STORAGE shades should be closed when the • For stubborn stains, use cleaner-degreaser. motorhome is parked for an extended period of time. UltraLeather Cleaning Chart Detergent/ Cleaner/ Type of Stain Water Degreaser WARNING Coffee, Tea ...
SECTION 11 – MAINTENANCE AND STORAGE stubborn stains, perform the following CABINETRY – CLEANING procedures for your stainless steel appliances to start shining again. Wooden items may be cleaned with a soft cloth and a good quality wood finish cleaning Scale product.
SECTION 11 – MAINTENANCE AND STORAGE • Do not use abrasive powder detergents that RANGE AND REFRIGERATOR could ruin the surface finish. For care and appearance maintenance of the • Do not use wool, abrasive brushes, or tools range and refrigerator, refer to the appliance that have previously cleaned other metals, manufacturer’s operation and maintenance because as well as scratching the surface, they...
SECTION 11 – MAINTENANCE AND STORAGE • Remove spills immediately with a damp BATHROOM cloth, followed by rinsing with clean water. • The use of stiletto heels is not recommended, Toilet as they may cause permanent damage to the For instructions on the care of your toilet, refer flooring.
SECTION 11 – MAINTENANCE AND STORAGE 9. Inspect all seams and seals around doors, VEHICLE STORAGE – windows, vents, and any other joints. Replace PREPARATION or repair any that are damaged. Sealing materials and compounds can be purchased Properly preparing your vehicle for storage from your dealer.
SECTION 11 – MAINTENANCE AND STORAGE 9. After flushing fresh waterlines, install a new CHASSIS SERVICE AND water filter cartridge on the galley sink water MAINTENANCE filter and/or full-coach water filteration system (if equipped). See appropriate filter Consult the appropriate sections in your installation instructions in Plumbing section.
SECTION 11 – MAINTENANCE AND STORAGE COACH MAINTENANCE CHART These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals. Always use specified sections or manufacturer’s guide for further information and instructions. Propane Gas System ...
Page 127
SECTION 11 – MAINTENANCE AND STORAGE COACH MAINTENANCE CHART These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals. Always use specified sections or manufacturer’s guide for further information and instructions. Safety Equipment Check operation of the following items: ...
Page 128
SECTION 11 – MAINTENANCE AND STORAGE COACH MAINTENANCE CHART These recommendations apply for normal recreational use. Heavy duty or full-time use may require more frequent maintenance intervals. Always use specified sections or manufacturer’s guide for further information and instructions. Sealants ...
SECTION 12 – MISCELLANEOUS NOTE: We recommend that you dump all LOADING THE VEHICLE holding tanks before traveling to avoid carrying unnecessary weight. NOTE: Your motorhome’s load capacity is designated by weight, not by volume, so you cannot necessarily use all available WARNING space when loading your motorhome.
Page 130
SECTION 12 – MISCELLANEOUS Corner Weighing (Side-to-Side) You will first drive only your front wheels onto the scale pad, then drive ahead so that the The most accurate method of weighing a whole vehicle is on the scale, then finally pull off motorhome is to weigh each “corner”...
SECTION 12 – MISCELLANEOUS axle is 12,000 lbs., then the load on each rear dual Because of individual vehicle use and loading set (left rear duals or right rear duals) should not habits, we recommend weighing the vehicle exceed 6,000 lbs. while fully loaded to avoid exceeding any of the listed Gross Weight Ratings.
SECTION 12 – MISCELLANEOUS Check state regulations on trailer weight and TRAILER WIRING trailer brake requirements to be sure you select CONNECTOR the right equipment before towing. Before descending a steep or long grade when Your coach is pre-wired for trailer or car towing a trailer, reduce speed and shift into a towing lights with a 7-pin socket.
(hinge side) of equipped with a Class 3 hitch may have a the screen door. label limiting vertical tongue load to 350 lbs. All Winnebago Industries models equipped with a Class IV hitch have a 12-5...
SECTION 12 – MISCELLANEOUS Automatic Mode - Entry Step This feature is intended to prevent injury or damage by an extended step while the vehicle is Switch ON moving. (Step Operates with Door) With the Step switch in the ON position, the Further Information step is in Automatic Mode.
Page 135
SECTION 12 – MISCELLANEOUS If the window will not open after three or more full turns of the knob, the glass may be stuck to the sealing gasket. Go to the outside of the coach and gently free the glass with your fingers. A periodic light dusting of talcum powder on the gasket should prevent this from recurring.
SECTION 12 – MISCELLANEOUS Manual Dome Fuse Fan Speed Crank Knob Selector Side Latch Bottom Latch View of interior right-hand side of window -Typical View Propping the Windows Open The bedroom and lounge windows are Power Roof Ventilator featured with prop rods on each side of the window.
SECTION 12 – MISCELLANEOUS Further Information See the power ventilator manufacturer’s operating instructions supplied in your InfoCase for further instructions, care, and cleaning information. STORAGE COMPARTMENT DOORS The high-density gaskets used on the exterior storage compartments are designed to provide a more positive seal against dust and weather.
SECTION 12 – MISCELLANEOUS EFFECTS OF PROLONGED Power OCCUPANCY Awning Switch Your motorhome was designed primarily for • Press to recreational use and short-term occupancy. If you Retract expect to occupy your coach for an extended (OUT). period, be prepared to deal with condensation and humid conditions that may be encountered.
Page 139
INDEX About this Manual ..........................1-1 Acrylic Glass Windows ........................11-9 Air Conditioner Filter ........................... 4-11 Air Conditioner/Heater – Automotive (Dash) ..................3-5 Audio-Video System Basic Operation ....................8-1 Bathroom .............................. 11-9 Battery Access ............................6-9 Battery Boost Switch ..........................3-8 Battery Care ............................
Page 140
Index Engine Cooling System .......................... 3-9 Engine Overheat ............................ 2-13 Entrance Door Prop Rod ........................12-9 Entry Step – Electric ..........................12-5 Exterior Automotive Paint Finish ......................11-2 Exterior Graphic Care ........................... 11-4 Exterior Lights ............................11-5 Exterior Shower/Wash Station ........................ 7-7 Fire Extinguisher .............................
Page 141
Index Power Cord – External ..........................6-1 Power Roof Ventilator .......................... 12-8 Power Sunvisor ............................3-4 Pre-Delivery Inspection .......................... 1-2 Pressure-Temperature Relief Valve ......................4-8 Pressure-Temperature Relief Valve (Tankless Water Heater) ..............4-9 Propane Gas Furnace ..........................4-9 Propane Gas Leak Detector ........................2-3 Propane Gas Leaks ..........................
Page 142
Index Suspension Alignment and Tire Balance ....................3-12 Tables and Countertops ........................11-7 Tires ..............................3-12 Toilet ............................... 7-7 Towing Guidelines ..........................12-4 Trailer Wiring Connector ........................12-4 TV – 12V LED ............................8-1 TV – Pull out ............................8-1 TV Antenna - Digital ..........................
Need help?
Do you have a question about the Reoy and is the answer not in the manual?
Questions and answers