Lighting Instructions - BuckMaster CDVB200 Owner's Operation And Installation Manual

Cast stove and direct-vent natural or l.p. (liquid propane) freestanding gas stove heater

Hide thumbs

Table Of Contents

Table of Contents

OPERATING STOVE

WITH BURNER SYSTEM

FOR YOUR SAFETY

READ BEFORE

LIGHTING

WARNING: If you do not follow these

instructions exactly, a fire or explosion

may result causing property damage,

personal injury or loss of life.

A. This appliance has a pilot which

must be lighted by hand. When

lighting

the pilot, follow these

instructions exactly.

B. BEFORE

LIGHTING

around the appliance area for gas.

Be sure to smell next to the floor

because some gas is heavier than air

and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electric switch; do

not use any phone in your building.

•

Immediately call your gas supplier

from a neighbor's phone. Follow the

gas supplier's instructions.

•

If you cannot reach your gas

supplier, call the fire department.

C. Use only your hand to push in or

turn the gas control knob. Never use

tools. If the knob will not push in or

turn by hand, don't try to repair it,

call a qualified service technician.

Force or attempted repair may

result in a fire or explosion.

D. Do not use this appliance if any part

has been under water. Immediately

call a qualified service technician to

inspect the appliance and to replace

any part of the control system and

any gas control which has been

under water.

P IL O T

Thermopile

Ignitor Electrode

1. Stop! Read the safety information

in column one.

2. "Set the thermostat to lowest."

3. "Turn off all electric power to the

appliance."

4. Open access cover door.

5. Turn control knob clockwise___

to the "OFF" position.

NOTE: Knob cannot be turned from

"PILOT" to "OFF" unless knob is

pushed in slightly.

6. "Wait five (5) minutes" to clear

out any gas. Then smell for gas,

including near the floor. If you

smell gas, STOP! Follow "B" in

smell

all

the safety information label. If

you don't smell gas, go to the next

step.

7. Pilot is located between the front

and rear burner.

8. Turn control Knob counter

clockwise ____

position.

9. Press in control knob. With

c o n t r o l

immediately push and release

ignitor button. This will light the

pilot.

NOTE: *If the control knob does not

pop up when released, "Stop" and

immediately

technician or gas supplier.

*If the pilot will not stay lit after

several tries, turn the gas control knob

to "OFF" and call your service

technician or gas supplier."

10. Continue to hold the control knob

pressed in for one (1) minute after

the pilot is lit. Release the control

knob and it will pop back up. Pilot

should remain lit. If it goes out,

repeat steps 5 thru 10.

Pilot Burner

11. Turn control knob counter

clockwise ____ to "ON" position.

12. Close access cover door.

13. Turn on all electric power to the

appliance.

14. If using unit without wall

thermostat place (AUTO/OFF/

M A N U A L )

"MANUAL" position. If using

wall thermostat place (AUTO/

OFF/MANUAL) switch in the

Thermocouple

"AUTO" position, and place wall

thermostat to a setting higher

than room temperature.

LIGHTING

INSTRUCTIONS

to the "Pilot"

k n o b

p r e s s e d

call

your

service

s w i t c h

i n

TO TURN OFF GAS

TO APPLIANCE

1. Set the thermostat to lowest

setting (if used).

2. Turn off all electric power to the

appliance if service is to be

performed.

3. Open access cover door.

4. Push in gas control knob slightly

and turn clockwise _____

"OFF". Do not force.

5. Close access cover door.

Sit Millivolt Valve

Variable

Flame Control

Knob

i n ,

PIEZO IGNITOR BUTTON LO-

CATED TO THE LEFT, BESIDE

THE SIDE OF THE GAS VALVE

Figure 40– Gas Valve & PIEZO IGNI-

TOR

MANUAL LIGHTING

PROCEDURE

1. Remove glass door (see Removing/

Replacing Glass Door, page 18).

2. Follow steps 1 through 8 under