Alliance Laundry Systems ATE50FWP431AW01 User Manual
  1. Manuals
  2. Brands
  3. Alliance Laundry Systems Manuals
  4. Washer
  5. ATE50FWP431AW01
  6. User manual

Alliance Laundry Systems ATE50FWP431AW01 User Manual

Homestyle stacked washer/dryers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Homestyle
Stacked Washer/
Dryers
Refer to Page 6 for Model Numbers
SWD452C
Part No. 802848R2
www.comlaundry.com
August 2011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ATE50FWP431AW01 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Alliance Laundry Systems ATE50FWP431AW01

Summary of Contents for Alliance Laundry Systems ATE50FWP431AW01

  • Page 1 Homestyle Stacked Washer/ Dryers Refer to Page 6 for Model Numbers SWD452C Part No. 802848R2 www.comlaundry.com August 2011...

  • Page 3: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 4 50. Thermal Fuse (Electric Models) ..........77 51. Heater Assembly (Electric Models)..........77 52. Cycling or Limit Thermostat............77 53. Door Switch ................78 Section 8 – Internal Wiring of Dryer Motor Switch......79 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 5: Section 1 - Safety Information

    • Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the machine is properly grounded and to reduce the risk of fire, electric shock, serious injury, or death. W284 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 6: Locating An Authorized Servicer

    Locating an Authorized Servicer Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs. Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician and using authorized factory parts.

  • Page 7: Section 2 - Introduction

    When calling or writing about your product, be sure to mention model and serial numbers. Model and serial Nameplate numbers are located on nameplate(s) as shown. SWD1199P 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 8: Model Identification

    FTE50FSP301NW01 LTUA7A*N LTE50FGP541NW23 LTUA7A*N2802 LTKA6A*N4350 LTUA9A*N LTL50FGP541NW23 LTZA7A*N LTSA7A*N LTZA7A*N2802 LTSA7A*N1500 LTZA9A*N LTSA7A*N2989 LTZA9A*N0902 LTSA7A*N3000 * Add Letter To Designate Color. W – White Q – Bisque © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 9: How Your Stacked Washer/Dryer Works

    Pressure Switch (Located inside control cabinet) Control Mixing (Located inside Valve control cabinet) Inner Basket Outer Inverter Control (Mounted to base of washer) SWD828N Electric Drain Pump Motor 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 10 After all the rinse cycles have been completed, the spin. washer goes into a final high spin cycle to extract as much water as possible from the clothing to prepare © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 11: Section 3 - Troubleshooting

    RPM. the belt. The knocking sound is made when the flat To correct this condition, replace the belt. spot hits the pulley. The knocking may occur 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 12: No Spin Due To Out-Of-Balance Switch Wiring Problem Starting Serial Nos. Beginning 0307

    From End of Terminals Wire Clamp First Section of Tape 4.5 In. (11.43 cm) From End of Terminals Wire Tie Cut Off Broken Wires Here FLW1842B Figure 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 13: Troubleshooting Leds On Washer Inverter Controls Starting Machine Serial No. 0911014603

    A no spin condition is not caused by intermittent operation of the motor or motor control (inverter assembly). DO NOT replace these components for no spin complaints if the unit passes the following procedure: 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 14 Is pressure cycle. Close door switch or and start washer. pressure switch wiring inoperative? Replace switch and/or wiring. FLW1789S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 15: Troubleshooting Shock Absorbers

    A large amount of grease/oil indicates a shock that might fail soon. Do not replace shock until the internal spring has broken as described in Step 2. 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 16 • Washer motor not grounded! Disconnect electric power before servicing motor. W502 Good Shock Shows Approximately 2 inches of Rod FLW1845B Figure 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 17: Section 4 - Dryer Troubleshooting

    • Washer motor not grounded! Disconnect electric power before servicing motor. W502 IMPORTANT: Refer to wiring diagram for aid in testing dryer components. 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 18: Dryer Motor Does Not Run

    Is loading Close door. windings and door closed? main windings. Continued on Test switch and next page. Is door switch replace if inoperative? inoperative. SWD1706S-a © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 19 Replace motor if shaft is locked up. Is motor wire Firmly press harness connection connection block onto block loose? motor switch. SWD1706S-b 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 20: Dryer Stops In Cycle; Quits After The First Few Loads; Has A Burning Smell; Cycles On Motor Thermal Protector

    Check fan for cylinder seals and item caught in obstruction. glides for wear or fan? damage. Check for clothes lodged between cylinder baffle and bulkhead. SWD1690S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 21: Dryer Motor Runs But Cylinder Does Not Turn

    Is belt routed on wrong side Reroute belt. of idler lever? Is idler arm Replace idler arm. bent? Wipe oil from Is there oil on cylinder? cylinder. SWD1691S 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 22: Dryer Motor Does Not Stop

    Test switch and Is door switch replace if inoperative? inoperative. Test timer and Is timer replace if inoperative? inoperative. SWD1707S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 23: Dryer Runs Only When Door Is Open

    11. Dryer Runs Only When Door is Open Dryer runs only when door is open. Rewire door Is door switch switch. Refer to miswired? wiring diagram. Replace door switch. SWD1693S 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 24: Dryer Heating Assembly Does Not Heat Or Burner Does Not Ignite

    FLUFF, inoperative. or inoperative? Electric Test thermal Models: Is fuse and thermal fuse replace if inoperative? inoperative. Continued on next page. SWD1708S-a © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 25 Test igniter and replace if Gas Models: inoperative. Is igniter Refer to Dryer inoperative? Test Procedures section. Is wiring Refer to wiring broken, loose diagram. or incorrect? SWD1708S-b 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 26: Igniter Does Not Glow (Gas Supply Sufficient) - Gas Dryer Models

    (pink and and wiring. blue wires)? Has flame sensor failed Replace sensor. with contacts open? Is igniter broken Replace igniter. or open? SWD1695S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 27: Burner Ignites And Goes Out Repeatedly - Gas Dryer Models

    Check gas supply and pressure. Is gas supply Make sure gas insufficient? shut-off valve is turned on. SWD1696S 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 28: Igniter Glows But Burner Does Not Ignite - Gas Dryer Models

    Are igniter Loosen screw and and bracket properly position improperly igniter and bracket installed on on burner tube burner tube assembly. assembly? SWD1697S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 29: Dryer Heater Assembly Or Burner Shuts Off Prematurely

    Is wiring Refer to wiring Gas Models: broken, loose Adjust flame. diagram. Is burner or incorrect? Refer to flame Adjustments improperly section. adjusted? SWD1709S 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 30: Dryer Heater Assembly Or Burner Repeatedly Cycles Off On Limit Thermostat

    Is limit thermostat Replace Is there lint in Disassemble cycling at too thermostat. internal dryer dryer ductwork low a ductwork? and clean. temperature? Continued on next page. SWD1710S-a © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 31 Is there an air replace seal if leak at blower necessary. seal? Check and Is there an air replace seal(s) leak at cylinder seal(s)? if necessary. SWD1710S-b 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 32: Dryer Heater Assembly Or Burner Does Not Shut Off

    Motor does Motor Does Not not stop? Stop paragraph. Is wiring Refer to wiring incorrect? diagram. Remove heater Has heater assembly and assembly check for short. shorted? SWD1700S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 33: Clothes Do Not Dry In Dryer

    Gas small? load. Company to correct. Is there Clean lint excessive Is belt Check for filter. lint on lint installed proper filter? improperly installation. (low RPM)? SWD1711S 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 34: Timer Does Not Advance In Automatic Cycle

    4. Seal between cylinder Instructions system and front or rear bulkhead. (supplied with unit) improper or 5. Gap between air duct and for exhaust inadequate? filter mounting. requirements. SWD1712S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 35: Clothes Are Too Hot When Removed From Dryer

    5. Gap between air duct and filter mounting. Test cycling Is cycling thermostat and thermostat replace if inoperative? inoperative. Is timer Test timer and inoperative replace if (not allowing inoperative. cool-down)? SWD1713S 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 36: Excessive Chattering Or Vibrating Noise In Dryer

    If the belt vibrates as it rotates inoperative? around the cylinder, the idler arm is making the noise. Replace the idler spring. Check blower fan for missing or cracked fan blades. SWD1703S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 37: Excessive Humming Or Whistling Noise In Dryer

    Is blower problem is originating from the housing blower housing. Replace the inoperative? current housing and cover. Check blower fan for missing or cracked fan blades. SWD1704S 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 38 Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 39: Section 5 - Washer Control Troubleshooting

    HEATING LED one-second on/one second off to indicate an open/ with heater) shorted temperature sensor error. This error will be cleared when the door is opened at the end of the cycle. 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 40: Washer Will Not Start - No Leds/Lights Lit (No Response To Start Switch)

    Is the Correct wiring configuration on "H7" header plugged configuration plug. into "H7"? Replace machine control. *Refer to machine serial plate for correct voltage. FLW1727S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 41 Washer Control Troubleshooting Washer Will Not Start – No LEDs/Lights Lit (No response to start switch) 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 42: Washer Will Not Start - Door Open Error (Wash/Rinse Leds Flashing - Door Must Be Closed And Attempting To Lock)

    120 Volts)* from the door switch. BLK wire on the door switch to neutral? Correct wiring to the door switch. *Refer to machine serial plate for correct voltage. FLW1770S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 43 Washer Control Troubleshooting Washer Will Not Start – Door Open Error (Wash/Rinse LEDs Flashing – Door must be closed and attempting to lock) 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 44: Washer Will Not Start - No Door Lock (Door Led Flashing)

    WHT/RED control and door and the PNK/BLK lock assembly. wires? Replace door lock assembly. *Refer to machine serial plate for correct voltage. FLW1729S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 45 Washer Control Troubleshooting Washer Will Not Start – No Door Lock (Door LED Flashing) 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 46: Washer Motor Will Not Run (Door/Final Spin Leds Flashing)

    Tach. Circuit: Approx. 115 ohms (Terminals 4-5) control. Refer to values Windings: Approx. 4 - 5 ohms (Terminals 1-2, 1-3, 2-3) at right. Replace motor. FLW1712S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 47 Washer Control Troubleshooting Motor Will Not Run (Door/Final Spin LEDs Flashing) 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 48: Washer Will Not Fill - No Communication Error (Wash/Door Leds Flashing)

    Is there 220-240 VAC Replace (or 120 Volts)* motor at the control. mixing valve? Replace mixing valve. *Refer to machine serial plate for correct voltage. FLW1730S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 49 Washer Control Troubleshooting Washer Will Not Fill – No Communication Error (Wash/Door LEDs Flashing) 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 50: Washer Overflows

    120 Volts)* across the coil of inoperative either the hot or cold pressure switch water solenoid? if necessary. Replace inoperative mixing valve. FLW1691S *Refer to machine serial plate for correct voltage. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 51 Washer Control Troubleshooting Washer Overflows 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 52: Pump Does Not Operate

    220-240 VAC (or between pump 120 Volts)* from "H6-2" to "H6-5" on the machine control. machine control? Replace machine control. FLW1692S *Refer to machine serial plate for correct voltage. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 53 Washer Control Troubleshooting Pump Does Not Operate 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 54: Serial Communication Error (Final Spin/Rinse Leds Flashing)

    *Refer to machine serial plate for correct voltage. **NOTE: Machine must be restarted to check voltage. Voltage is intermittently present for the first 15 seconds until error mode is displayed. FLW1731S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 55 Washer Control Troubleshooting Serial Communication Error (Final Spin/Rinse LEDs Flashing) 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 56: Washer Will Not Heat - Open/Shorted Temperature Sensor (Heating Led Flashing At End Of Cycle) (Models Equipped With Heater)

    500-35000 Ohms? Using an Ohmmeter, is the resistance value Replace thermistor/heater at the thermistor assembly. between 500-35000 Ohms? Check wiring to thermistor. FLW1723S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 57 Washer Control Troubleshooting Washer Will Not Heat – Open/Shorted Temperature Sensor (Heating LED Flashing at End of Cycle) (Models equipped with heater) 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 58: Washer Will Not Heat (Models Equipped With Heater)

    1-2 on on machine the heat relay? control? Correct wiring Replace between heat relay heat relay. *Refer to machine serial plate and control. for correct voltage. FLW1732S © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 59 Washer Control Troubleshooting Washer Will Not Heat (Models equipped with heater) 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 60 Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 61: Section 6 - Adjustments

    Rubber CAUTION SWD833N Foot DO NOT slide washer across floor if the Figure 4 leveling legs have been extended, as legs and base could become damaged. W248 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 62: Washer Loading Door

    Refer to Figure 5. Hinge Loading Door Screw FLW1771S Figure 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 63: Washer Motor Belt Tension

    Refer to Figure 6. Inner Basket Pulley Pivot Bolt Adjusting Belt Bolt 1/4 Inch Motor Mounting Bracket Motor Pulley Pivot Bolt Metal Wire Harness SWD1705S Adjusting Bolt Figure 6 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 64: Washer Door Catch

    Adjust door catch so the outside edge is aligned with the edge of the lock. Refer to Figure 8. Outer Bezel Inner Bezel Cut Away FLW1777S Figure 7 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 65 • Washer motor not grounded! Disconnect electric power before servicing motor. W502 Funnel Door Catch Door Lock Alignment of These Two Edges 802803 Catch H250SE3B SHOWN CLOSED Figure 8 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 66: Shipping Braces

    Removal of supports prior to final installation may cause Shock Absorber Shipping Support Shock Absorber Shipping Support Shipping Bracket FLW821S Figure 9 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 67: Burner Flame (Gas Models)

    Air Shutter Lockscrew Shut-Off Valve Handle Shutter 1/8 Inch Pipe Plug (For checking manifold pressure) D265SE3A Figure 10 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 68 Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 69: Section 7 - Dryer Test Procedures

    NOTE: Timer Motor Resistance: Motor 120 Volt, 60 Hz 2,460 – 3,100 Ohms Wires 240 Volt 10,900 – 13,000 Ohms 24 Volt 80 – 130 Ohms Figure 11 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 70: Fabric Selector Switch

    – FABRIC SELECTOR SWITCH 3 Position L1-2 L1-3 L1-1 Fluff (No Heat) – – Delicate – Perm. Press – – Normal (Regular) – – X indicates closed © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 71: Drive Motor

    120 Volt 2,460 – 3,100 Ohms disconnect block. 240 Volt 10,000 - 13,000 Ohms Motor Motor Switch Disconnect Block Motor and Exhaust Assembly Drive Motor D326SE3A Figure 12 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 72 1 and switch terminal 2. F. Manually depress actuator. Inoperative start Continuity exists between switch switch. Replace switch. terminal 1 and switch terminal 2. Motor switch checks O.K. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 73 I. Continuity exists between Inoperative protector. Protector orange or copper wire on back Replace motor. of switch and brown or blue wire in terminal 4. All motor windings check O.K. 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 74: Motor Switch

    Figure 13. Mounting Thermal Overload Protector Motor Switch D029KE3A Figure 13 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...
  • Page 75 Step installation. “b”. Refer to Figure 18. Thermal Overload Protector Plastic Clip Top Of Motor Switch Motor Switch D359SE3A Figure 14 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 76: Burner System Operation

    In approximately 30 seconds, the igniter attains is turned off. ignition temperature and ignition is made. The heat from the burner flame causes the sensor contacts (located on burner housing beside the © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 77: Electrical Circuit To Ignition System (Gas Models)

    NOTE: If meter registers any other readings than those listed above, the respective coil(s) should be replaced. Holding D270SE3A And Booster Coil GAS VALVE FOR SILICON CARBIDE IGNITION Figure 16 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 78: Sensor Check (Gas Models)

    NOTE: If meter does not read appropriate Ohms, then replace the igniter. IMPORTANT: Always examine all wires, terminals and connectors to be sure wiring is correct before replacing any components. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 79: Thermal Fuse (Electric Models)

    (2) Meter should read “zero.” d. Set meter to read Ohms. Apply meter probes to the heater assembly terminals. Meter should read as follows: (Cold Ohms). 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...

  • Page 80: Door Switch

    Apply probes to terminals 1 and 2 with door closed. The meter should read “infinite”. g. Open door. Meter should read “infinite” between 1 and 3 and “zero” between 1 and 2. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

  • Page 81: Section 8 - Internal Wiring Of Dryer Motor Switch

    • Washer motor not grounded! Disconnect electric power before servicing motor. W502 MAIN START ORANGE/COPPER CUSTOMER CIRCUIT PUSH TO START LINE Motor Switch Attaching Screws SWITCH SHOWN IN START POSITION R.S.P.C. D329SE3D Figure 18 802848 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
  • Page 82 Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 802848...

This manual is also suitable for:

Ltsa7a*n3300Bte50fsp171tw01Ltsa9a*nBte50fsp281cw01Ltsa9a*n1180Btg50fsp091cw01 ... Show all

Table of Contents