Table of Contents
Advertisement
SETUP (Continued)
SETTING THE ALARM
The ALARM function allows the user to set the
recording duration, speed to be recorded and tape
recycle for alarm recordings. When a contact clos-
ure occurs at the ALARM IN input, the VCR
automatically enters the RECORD mode at the pre-
programmed ALARM recording speed. (See Alarm
In, page 8 for a complete description of the ALARM
sequence.) The ALARM recording duration can last
from 5 seconds to TAPE END, or until the contact
closure is reopened.
The
ALARM
recording
programmed to 03, 12 or 24.
The checking signal is automatically recorded on the
tape at the beginning of each ALARM recording.
Later, you can easily locate the start of each
recording by using these signals when watching a
recorded content. See "ALARM INDEX SEARCH"
on page 21 for details.
The TIME/DATE display is set as follows during
ALARM display.
— ALARM stars ( ) will replace the colons (:).
— The recording speed will be changed to 03, 12 or
24 which was selected at the "SPEED" setting in
the ALARM display.
DURATION: User programmable length or time the unit
stays in the alarm record mode. (MANUAL, 5 SEC, 15
SEC, 30 SEC, 1 MIN, 3 MIN, 5 MIN, 10 MIN, 30 MIN, 60
MIN or TAPE END)
ALARM RECORDING TAPE SPEED
(03, 12 or 24)
ALARM READY (YES or NO)
[
A
L
ARM
SET
DU
R
A
T I ON
:
M
SPE D :
E
A
LARM
R
A E
Y D
:
YE
A
LARM
O T U
:
DU
[
R
ECY
CL
E
FU
NC
RE
W
I ND ,
S
TOP
I F
RECYCLE FUNCTIONS
("REWIND, STOP IF ALARM", "REWIND, STOP" or
"REWIND, RE-REC")
ALARM Display Format Description
17
speed
can
be
pre-
]
AN
U
AL
03
S
R T I ON
A
S ]
T
I ON
A
LARM
ALARM OUT
(DURATION or PULSE)
Notes:
• When the ALARM recording ends, the unit will
return to the original record speed and restore the
original record speed values to the TIME/DATE
displays.
• Select 03 at the "SPEED" setting when the dur-
ation is within 30 seconds. If the 12 or 24 speed is
selected, electronic "marks" are not recorded on
the tape and alarm index search will not operate.
1. Press the START/STOP button. The duration
setting flashes on/off.
2. Press the UP or DOWN button until the desired
setting appears on the monitor. (MANUAL, 5,
15, 30 SEC, 1, 3, 5, 10, 30, 60MIN, TAPE END)
3. Press the SET button. The record speed setting
flashes on/off.
4. Press the UP or DOWN button until the desired
setting appears on the monitor. (03, 12 or 24
hours.)
5. Press the SET button. The alarm ready setting
flashes on/off.
6. Press the UP or DOWN button to select the
alarm ready function. (YES or NO)
Select "YES" if you want to start alarm
recording even in the normal record or stop
mode.
Select "NO" if you do not want alarm recording
in the stop mode.
7. Press the SET button. The alarm out setting
flashes on/off.
8. Press the UP or DOWN button to select the
alarm out function. See "ALARM OUT" on page
8 for details. (DURATION or PULSE)
9. Press the SET button.
The RECYCLE position flashes on/off.
10. Press the UP or DOWN button to select the
mode at the end of tape. See "TAPE RECYCLE"
on page 19 for details.
11. Press the START/STOP button.
Programming for the ALARM has been com-
pleted.
Note:
To record the time and date, press the
PROGRAM button so they are displayed.
AVR24TLAX (E) QR34283
Advertisement
Table of Contents
