ParaBody 250101 Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. ParaBody Manuals
  4. Home Gym
  5. 250101
  6. Assembly instructions manual
ParaBody 250101 Assembly Instructions Manual

ParaBody 250101 Assembly Instructions Manual

Parabody home gym assembly instructions
Hide thumbs

Advertisement

Table of Contents

250101 HOME GYM

ASSEMBLY INSTRUCTIONS

Part # 6719701
1
Revision: 09/9/98

Advertisement

Table of Contents
loading

Related Manuals for ParaBody 250101

Summary of Contents for ParaBody 250101

  • Page 1: Home Gym

    250101 HOME GYM ASSEMBLY INSTRUCTIONS Part # 6719701 Revision: 09/9/98...

  • Page 2: Tools Required For Assembly

    2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.

  • Page 3: Parts List

    PART # DESCRIPTION 6594303 LEG CURL EXT 6593703 FRONT UPRIGHT 6593503 PRESS ARM 6594102 PRESS SEAT 6501302 SWIVEL PULLEY BRACKET 6594702 FLOATING PULLEY BRACKET 6718503 TOP BOOM 6718203 BASE 6717803 REAR UPRIGHT 6717502 CALF BLOCK 6275302 LAT BAR 6597402 SEAT PAD 6468401 3/4 X 7”...
  • Page 4 3/8 X 2-3/4” 48 FIGURE 1 STEP 1 • Loosely assemble the REAR UPRIGHT (9) to the BASE (8) using two 1/2 X 3” BOLTS (46), two 1/2” FLAT WASHERS (39), and two 1/2” LOCK NUTS (40). See FIGURE 1. •...
  • Page 5 STEP 2 • Insert two WEIGHT PLATE BUSHINGS (23) into the “PARABODY” side of each of the fifteen WEIGHT PLATES (58) as shown in FIGURE 2. STEP 3 • Securely assemble the WEIGHT STACK SHAFT (21) to the HEAD PLATE (20) using one 3/8 X 1- 1/4”...
  • Page 6 FIGURE 4 STEP 4 • Swing the GUIDE RODS (16) under the TOP BOOM (7) as shown on FIGURE 4. FIGURE 5 STEP 5 • Loosely assemble the TOP BOOM (7) to the REAR UPRIGHT (9) using two 1/2 X 3” BOLTS (46), two 1/2” WASHERS (39), and one 1/2”...
  • Page 7 FIGURE 6 STEP 6 • Insert two 3/4" FLANGE BEARINGS (29) into the TOP BOOM (7) as shown in FIGURE 6. • Screw the ADJUSTABLE GLIDE (37) approximately 1/2” into the FRONT UPRIGHT (2) and tighten jam nut securely as shown. •...
  • Page 8 3/8 X 7-1/2” 51 FIGURE 7 STEP 7 • Loosely assemble two 4-1/2” PULLEYS (18) to the PRESS ARM (3) using two 3/8 X 7-1/2” BOLTS (51), four 3/8” WASHERS (38), four 3/8 X 1” SPACERS (32), and two 3/8” LOW HEIGHT LOCK NUTS (43) as shown in FIGURE 7. Once both PULLEYS are installed, you may securely tighten these two connections.
  • Page 9 48 3/8 X 2-3/4” FIGURE 8 STEP 8 • Securely assemble one SPRING PIN ASSEMBLY (35) and one 3 PRONG KNOB (33) to the FRONT UPRIGHT (2) as shown. • Apply eight PARAGLIDES (57) to the INSIDE of the tube on the FRONT UPRIGHT (2) as shown. •...
  • Page 10 1/2 X 3” 46 LOW HEIGHT 42 FIGURE 9 STEP 9 • Insert two 1/2” FLANGE BEARINGS (30) into the the LEG CURL EXT (1) as shown. • Assemble the LEG CURL EXT (1) to the FRONT UPRIGHT (2) using one 1/2 X 3” BOLT (46) and one 1/2” LOW HEIGHT LOCK NUT (42).
  • Page 11 3/8 X 2-3/4” 48 FIGURE 10 STEP 10 • Securely assemble the CALF BLOCK (10) to the BASE (8) using two 3/8 X 2-3/4” BOLTS (48), two 3/8” WASHERS (38), and two 3/8” LOCK NUTS (41) as shown in FIGURE 10. (Note: The CALF BLOCK can be assembled to either side of the BASE.) •...

  • Page 12: Table Of Contents

    FIGURE 11 STEP 11 • Attach two 4 X 7” ROLLER PADS (15) to the FRONT UPRIGHT (2) using one 3/4 X 16” TUBE (14) and two 3/4” STARLOCK COLLARS (52) as shown in FIGURE 11. • Attach two 4 X 7” ROLLER PADS (15) to the PRESS SEAT (4) using one 3/4 X 16” TUBE (14) and two 3/4” STARLOCK COLLARS (52) as shown in FIGURE 11.

  • Page 13: Figure 13

    FIGURE 13 * All connections use one 3/8 X 2-3/4” BOLT (48), two 3/8” FLANGE SPACERS (36), and one 3/8” LOCK NUT (41). 48 3/8 X 2-3/4” STEP 13 • Securely assemble the ball end of the WEIGHT STACK CABLE (26) and one 3-1/2” PULLEY (19) to the TOP BOOM (7) using one 3/8 X 2-3/4”...

  • Page 14: Step 14

    * All connections use one 3/8 X 2-3/4” BOLT (48), two 3/8” FLANGE SPACERS (36), and one 3/8” LOCK NUT (41). 3/8 X 2-3/4” 48 FIGURE 14 STEP 14 • Securely assemble the WEIGHT STACK CABLE (26) and two 3-1/2” PULLEYS (19) to the TOP BOOM (7) using two 3/8 X 2- 3/4”...

  • Page 15: Securely Assemble One 4-1/2" Pulley (18) To The Floating Pulley Bracket (6) Using One 3/8 X 1-3/4" Bolt (49) And One 3/8" Lock Nut (41) As Shown In Figure

    3/8 X 1-1/4” 44 FIGURE 15 STEP 15 • Securely assemble one 4-1/2” PULLEY (18) to the FLOATING PULLEY BRACKET (6) using one 3/8 X 1-3/4” BOLT (49) and one 3/8” LOCK NUT (41) as shown in FIGURE 15. • Securely assemble one 3-1/2” PULLEY (19) to the BASE (8) using one 3/8 X 1-3/4” BOLT (49), one “L” BRACKET (55), and one 3/8”...

  • Page 16: Figure 16

    FIGURE 16 STEP 16 • If upon completion of assembly, the HEAD PLATE (20) does not sit on top of the first WEIGHT PLATE (58), push the HEAD PLATE (20) down, insert the WEIGHT STACK PIN (34) and perform several repetitions at the press station. This will relax the cable system and prevent the HEAD PLATE (20) from lifting up.
  • Page 17 (28) and one 12 LINK CHAIN (31) as shown in FIGURE 16. Thank you for purchasing the Parabody 250101 Home Gym. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714.
  • Page 18 250101 ADDENDUM INSTRUCTIONS 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2...

This manual is also suitable for:

Serious steel 250101

Table of Contents