External Control - NEC MultiSync X841UHD User Manual

HEAT STATUS
FAN CONTROL
SCREEN SAVER
GAMMA*
BACKLIGHT*
MOTION
SIDE BORDER COLOR
CHANGE PASSWORD
SECURITY
RESET

EXTERNAL CONTROL

NETWORK
INFORMATION
IP ADDRESS SETTINGS
IP SETTING
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
DNS
DNS PRIMARY
DNS SECONDARY
LAN POWER
DDC/CI
PING
IP ADDRESS RESET
RESET
*: If SPECTRAVIEW ENGINE is ON, this function is grayed out.
Displays status of the FAN, BACKLIGHT and TEMPERATURE.
Cooling fan reduces the temperature of the display to protect from overheating.
If "AUTO" is selected, you can adjust the start temperature of the cooling fan and fan speed.
Use the SCREEN SAVER function to reduce the risk of Image Persistence.
NOTE: This function is released when INPUT CONFIGURATION is active. When SCREEN
SAVER is ON, the image will be changed FULL image. After released SCREEN SAVER, the
image will be displayed with current ASPECT setting.
3840 x 2160 (60 Hz) input cannot be selected.
When SCREEN SAVER is active, MULTI PICTURE, STILL, IMAGE FLIP except for NONE or
TEXT TICKER, POINT ZOOM are not available.
The display gamma is changed and fi xed when "ON" is selected.
The brightness of backlight is decreased when "ON" is selected.
NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at
user determined intervals. You can set interval time and zooming ratio.
Adjusts the color of the side borders when a 4:3 image is displayed.
Press + button, the bar will become lighter.
Press - button, the bar will become darker.
Allows the security password to be changed.
The factory preset password is 0000.
Locks the security password.
Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:
POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR.
Displays current network settings.
NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN
SETTING is applied.
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from
your network administrator.
NOTE: Consult your network administrator for the IP address when "AUTO" is selected for
[IP SETTING].
Set your IP address of the network connected to the monitor when "MANUAL" is selected for
[IP SETTING].
Set your subnet mask number of the network connected to the monitor when "MANUAL" is
selected for [IP SETTING].
Set your default gateway of the network connected to the monitor when "MANUAL" is selected
for [IP SETTING].
NOTE: Set as [0.0.0.0] to delete the setting.
Set for IP ADDRESS SETTINGS of DNS server.
AUTO: Automatically assign an IP address of DNS server connected to the monitor.
MANUAL: Set your IP address of DNS server connected to the monitor.
Set your primary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
Set your secondary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
Selects LAN operation mode. When "ON" selected, allows to supply power to LAN during power
save mode or standby mode.
NOTE: For enabling "AUTO ID", this function should be ON.
ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.
Confi rm the response by communicating to the preset IP address.
Resets IP ADDRESS SETTINGS back to factory settings.
Resets the following setting within the EXTERNAL CONTROL menu back to factory settings:
DDC/CI.
English-28
-
AUTO, HIGH
OFF
OFF
OFF
15
-
OFF
-
-
AUTO
192.168.0.10
255.255.255.0
0.0.0.0
AUTO
0.0.0.0
0.0.0.0
OFF
ENABLE
192.168.0.10
NO
-
-