Download Print this page

NEC MultiSync X461UNV User Manual

46" low-bright ultra-narrow professional-grade large-screen display.
Hide thumbs

Advertisement

User's Manual
MultiSync X462UN
MultiSync X461UNV

Advertisement

   Also See for NEC MultiSync X461UNV

   Related Manuals for NEC MultiSync X461UNV

   Summary of Contents for NEC MultiSync X461UNV

  • Page 1

    User’s Manual MultiSync X462UN MultiSync X461UNV...

  • Page 2: Table Of Contents

    Index Declaration of conformity ... English-1 Important Information ... English-2 WARNING, CAUTION ... English-2 Declaration ... English-2 Safety Precautions, Maintenance & Recommended Use ... English-3 Contents ... English-4 Installation ... English-5 Parts Name and Functions ... English-7 Control Panel ... English-7 Terminal Panel ...

  • Page 3: Declaration Of Conformity

    Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland. DisplayPort is trademarks of Video Electronics Standards Association.

  • Page 4: Important Information

    WARNING CAUTION European U.K. Continental EU (except U.K.) U.K. Declaration of the Manufacturer and marked with Warning English-2 Chinese Japanese China NEC Display Solutions, Ltd. 4-13-23, Shibaura, Minato-Ku Tokyo 108-0023, Japan Japan...

  • Page 5: Safety Precautions, Maintenance & Recommended Use

    • Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable. • The screen of the coaxial cable is intended to be connected to earth in the building installation.

  • Page 6: Contents

    Contents Your new MultiSync monitor box* should contain the following: • LCD monitor • Power cord* • Video Signal Cable • Remote control cable • Setup Manual • Cable cover Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) Power Cord* Remote control cable CD-ROM...

  • Page 7: Installation

    Please note the following when mounting on wall or ceiling • When using mounting accessories other than those that are NEC approved, they must comply with the VESA- compatible (FDMlv1) mounting method. • NEC strongly recommends Unit using size M6 screws...

  • Page 8: Ventilation Requirements

    The protective sheet was wrapped around the LCD in the original packaging. Make sure there is nothing on the table that can damage the monitor. When using mounting accessories other than NEC compliant and approved, they must comply with the VESA- compatible mounting method.

  • Page 9: Parts Name And Functions

    Parts Name and Functions Control Panel POWER button Switches the power on/off. See also page 16. MUTE button Switches the audio mute ON/OFF. INPUT button Acts as SET button within OSD menu. (Toggle switches between [DVI], [DPORT], [VGA], [RGB/HV], [HDMI], [DVD/HD1], [DVD/HD2], [SCART], [VIDEO1], [VIDEO2], [S-VIDEO] or [TV]*).

  • Page 10: Terminal Panel

    Terminal Panel Main Power Switch On/Off switch to turn main power ON/OFF. AC IN connector Connects with the supplied power cord. DISPLAYPORT connector To input DisplayPort signals. HDMI connector To input digital HDMI signals. DVI IN (DVI-D) To input digital RGB signals from a computer or HDTV device having a digital RGB output.

  • Page 11

    LAN port (RJ-45) LAN connection. See page 31. REMOTE IN/OUT Use the optional wired remote control by connecting it to your monitor. NOTE: When you use Remote IN/OUT, IR CONTROL in OSD menu should be NORMAL. Kensington Lock For security and theft prevention. Remote control sensor Receives the signal from the remote control.

  • Page 12: Wireless Remote Control (optional)

    Wireless Remote Control (Optional) POWER button Switches the power on/standby. INPUT button Selects input signal. DVI: DVI DISPLAYPORT: DPORT VGA: VGA RGB/HV: RGB/HV HDMI: HDMI DVD/HD: DVD/HD1, DVD/HD2, SCART VIDEO: VIDEO1, VIDEO2 S-VIDEO: S-VIDEO OPTION: Depends on your connection PICTURE MODE button Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [AMBIENT1], [AMBIENT2].

  • Page 13: Operating Range For The Option Remote Control

    REMOTE ID button Activates REMOTE ID function. MTS button* AUDIO INPUT button Selects audio input source [IN1], [IN2], [IN3], [DPORT], [HDMI], [TV]* , [OPTION]* button Activates closed captioning. Note: VIDEO1, VIDEO2, S-VIDEO inputs only. *: This button’s action depends on which option board you use. Refer to the option board’s manual for further information.

  • Page 14: Setup

    C. Replace the cover. CAUTION: Incorrect usage of batteries can result in leaks or bursting. NEC recommends the following battery use: • Place “AA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment.

  • Page 15

    5. Attach the cable cover • Use six of the M4 x 8 screws (black) (included) to attach the cable cover. 6. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer first.

  • Page 16: Connections

    Connections NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a loss of the monitor image. NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound. Before making connections: First turn off the power of all the attached equipment and make connections.

  • Page 17: Connecting A Personal Computer

    Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards with a pixel clock over 162MHz may not display an image correctly. Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically. <Typical factory preset signal timing>...

  • Page 18: Basic Operation

    Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off. NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the Power Button on the front of the LCD.

  • Page 19: Power Indicator

    Power Indicator Mode Status Indicator Light Power ON Green* Power OFF (Eco Standby)* Power consumption under 0.5W* Power OFF (Standby) Amber Power consumption under 1W* Power Save Amber Blinking Power consumption under 2W* Power Standby when Green and Amber blink alternately “SCHEDULE SETTINGS”...

  • Page 20: Picture Mode

    Picture Mode DVI, VGA, RGB/HV, DPORT STANDARD sRGB AMBIENT1 HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* STANDARD CINEMA AMBIENT1 AMBIENT Mode The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room.

  • Page 21: Osd (on-screen-display) Controls

    OSD (On-Screen-Display) Controls NOTE: Some functions may not be available depending on the model or optional equipment. Input source Main Menu Icons Main Menu Item Sub Menu PICTURE MODE Select Press UP or DOWN button to select sub-menu. Remote Control Press UP or DOWN button to select.

  • Page 22: Picture

    DICOM GSDF curve simulated for LCD type. PROGRAMMABLE Gamma curve of the factory setting is installed. A programmable gamma curve can be re-loaded using NEC optional software. MOVIE SETTINGS NOISE REDUCTION Adjusts the amount of noise reduction. Press + or - to adjust.

  • Page 23: Audio

    H RESOLUTION Adjusts the horizontal size of the image. VGA, RGB/HV inputs only V RESOLUTION Adjusts the vertical size of the image. VGA, RGB/HV inputs only INPUT RESOLUTION If there is a problem with signal detection, this function forces the monitor to display the signal at the desired resolution.

  • Page 24: Pip

    SCHEDULE RESET Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER, SCHEDULE SETTINGS. KEEP PIP MODE Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off. When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD. PIP MODE Picture-in-Picture SIDE BY SIDE (ASPECT) SIDE BY SIDE ASPECT...

  • Page 25: Multi Display

    INFORMATION OSD Selects whether the information OSD is displayed or not. The information OSD will be displayed when the input signal or source changes. The information OSD will also give a warning when there is no-signal or the signal is out-of range. An interval between 3 to 10 seconds for the Information OSD to appear is available.

  • Page 26: Display Protection

    LAN SETTING When you use this function, EXTERNAL CONTROL should be “LAN”. NOTE: When changing the LAN SETTING, turn the monitor off and then back on. After turning on the monitor, you need to wait several seconds until the LAN SETTING is applied. DHCP Enabling this option automatically assigns an IP address to the monitor from your DHCP server.

  • Page 27: Advanced Option

    ADVANCED OPTION INPUT DETECT Selects the method of input detection the monitor uses when more than two input devices are connected. All inputs except for TV* NONE The Monitor will not search the other video input ports. FIRST DETECT When the current video input signal is not present, then the monitor searches for a video signal from the other video input port.

  • Page 28

    COLOR SYSTEM The selected Color System depends on the video format of the input signal. VIDEO1, VIDEO2, S-VIDEO inputs only AUTO Automatically chooses Color System setting based on input signal. NTSC SECAM 4.43 NTSC PAL-60 SCAN MODE Some video formats may require different scanning modes in order to best display the image. HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only OVER SCAN Image size is larger than what can be displayed.

  • Page 29

    As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

  • Page 30: Remote Control Function

    Remote Control Function REMOTE CONTROL ID FUNCTION REMOTE CONTROL ID The optional remote control can be used to control up to 100 individual MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync monitors.

  • Page 31

    3. Press the “DISPLAY” button on the remote control while aiming at the “PRIMARY” monitor. The Information OSD will be shown at top left side of the screen. Monitor ID: Displays the ID number of the current monitor within the daisy chain. Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor.

  • Page 32: Controlling The Lcd Monitor Via Rs-232c Remote Control

    Controlling the LCD monitor via RS-232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C” (See page 23). Functions that can be controlled by a personal computer are: •...

  • Page 33: Controlling The Lcd Monitor Via Lan Control

    Controlling the LCD monitor via LAN Control Connecting to a Network Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function. NOTE: When you use this function, EXTERNAL CONTROL should be “LAN” (See page 23). To use a LAN connection, you are required to assign an IP address.

  • Page 34: Network Settings

    Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL.

  • Page 35

    Alert Mail Setting http://<the Monitor’s IP address>/lanconfig.html This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be sent when an error occurs in the monitor. Alert Mail Checking [ENABLE] will turn on the Alert Mail feature. Checking [DISABLE] will turn off the Alert Mail feature.

  • Page 36: Features

    FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size. VESA Standard (FDMIv1) Mounting Interface: Allows you to connect your LCD monitor to any VESA standard (FDMIv1) third party mounting arm or bracket. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America.

  • Page 37: Edge Comp Function (x462un Only)

    EDGE COMP Function (X462UN only) EDGE COMP function (Page 26) adjusts the brightness difference between the center and the edge of the screen. Adjust the brightness in accordance with your monitor. BRIGHTNESS: Reduces the brightness in the center of the screen to allow for better consistency to the brightness at the edge of the screen.

  • Page 38: Troubleshooting

    NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

  • Page 39: Specifications - X462un

    Specifications - X462UN Product Specifications LCD Module Pixel Pitch: Resolution: Brightness: Contrast Ratio: Viewing Angle: Design View Distance: Frequency Horizontal: Pixel Clock Viewable Size Input Signal DVI-D 24pin Digital RGB DisplayPort DisplayPort Connector Digital RGB 15pin Mini D-sub Analog RGB Sync RGB/HV BNC (R,G,B,H,V)

  • Page 40: Specifications - X461unv

    Specifications - X461UNV Product Specifications LCD Module Design View Distance: Frequency Pixel Clock Viewable Size Input Signal DVI-D 24pin Digital RGB DisplayPort DisplayPort Connector Digital RGB 15pin Mini D-sub Analog RGB Sync RGB/HV BNC (R,G,B,H,V) Analog RGB Sync HDMI HDMI Connector Digital RGB DVD/HD1 RCA (Y, Cb/Pb, Cr/Pr)

  • Page 41: Pin Assignment

    Pin Assignment 1) RS-232C input/output Pin No Name connected to 7&8 connected to 6 connected to 4 connected to 1&8 connected to 1&7 This LCD monitor uses RXD, TXD and GND lines for RS-232C control. 2) REMOTE IN 3) REMOTE OUT D-SUB 9P English-39...

  • Page 42: Manufacturer's Recycling And Energy Information

    Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

This manual also for:

Multisync x462un, X461unv-tmx4d, X462un-tmx4d, Multisync x461unv

Comments to this Manuals

Symbols: 0
Latest comments: