Monogram ZV1050 Installation Instructions Manual

Monogram ZV1050 Installation Instructions Manual

42" island
Hide thumbs Also See for ZV1050:

Advertisement

Quick Links

monogram.com
Installation
Instructions
42" Island
Vent Hood
ZV1050
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZV1050 and is the answer not in the manual?

Questions and answers

Summary of Contents for Monogram ZV1050

  • Page 1 Installation Instructions 42" Island Vent Hood ZV1050 monogram.com...
  • Page 2: Safety Information

    Safety Information BEFORE YOU BEGIN WARNING: Read these instructions completely and carefully. TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR • IMPORTANT INJURY TO PERSONS, OBSERVE THE FOLLOWING: – Save these instructions for local A. Use this unit only in the manner intended by the inspector’s use.
  • Page 3: Table Of Contents

    Design Information CONTENTS Design Information Step 3, Check Installation Hardware .......... 10 Product Dimensions ................3 Step 4, Mount Template..............11 Duct Cover Accessories ..............3, 4 Step 5, Install Support Frame ............11 Determine Installation Height ............4 Step 6, Secure Wiring ................. 12 Advance Planning Step 7, Size and Install Ductwork ..........
  • Page 4: Duct Cover Accessories

    9'0" 25-1/2" to 30" ZX1059SFSS cooking surface. 9'1" 25-1/2" to 30" ZX10510SFSS • When installing the Island Hood above a Monogram Profes- sional Range or Rangetop, installation clearance must be 9'2" 25-1/2" to 30" ZX10510SFSS at least 30". 9'3" 25-1/2" to 30"...
  • Page 5: Advance Planning

    Advance Planning POWER SUPPLY TOOLS AND MATERIALS REQUIRED (not supplied) IMPORTANT – Please read carefully. • Tape measure WARNING: • Knife FOR PERSONAL SAFETY, THIS • Spirit level APPLIANCE MUST BE PROPERLY GROUNDED. • Wire cutter • Wire stripper AVERTISSEMENT : •...
  • Page 6: Duct Fittings

    Advance Planning Total DUCT FITTINGS Equivalent Quantity Equivalent Duct Piece Dimensions Length* Used Length This Hood Must Round, 1 ft. Use 8" Round Duct. straight (per foot It Can Transition to length) 3-1/4" x 12" Duct. 1 ft. 3-1/4" x 12" (per foot Use this chart to compute maximum straight...
  • Page 7: Installation Instructions

    Installation Instructions STEP 1 CONSTRUCT CEILING SUPPORT Ceiling Plan the location Hood Determine the exact location of the vent hood. Ducting Centerline • Use a plumb bob to check location to be sure countertop/cook- top location below the hood will align exactly. •...
  • Page 8 Installation Instructions STEP 1 CONSTRUCT CEILING SUPPORT (cont.) EXAMPLE B 16" Joist 11-1/4" Install Cross-Framing Spacing Symmetrically About Duct/Cooktop Centerline 2x4 Cross- Framing 8" Duct 7-1/4" Cooktop Align Duct to Outline Center of Cooktop Front of Hood Top View—Ceiling Joists Run Perpendicular to Front of Hood EXAMPLE C 2x4 Cross- 11-1/4"...
  • Page 9 Installation Instructions STEP 1 CONTINUED • Arrange cross-framing in the ceiling to suit the existing structure. See examples. – Secure each 2 x 4 block with at least four (4) #10 wood screws, 3" long (not supplied). Use 8 wood screws total for the two supports.
  • Page 10: Step 2, Remove Packaging

    Installation Instructions STEP 2 REMOVE THE PACKAGING The vent hood is packed separately from the decorative duct cover or accessory covers ZX1059SFSS or ZX10510SFSS. • Remove the frame, cover, parts box and packaging. • Remove junction box cover. • Install strain relief onto junction box cover. STEP 3 CHECK INSTALLATION HARDWARE AND ACCESSORIES Locate the hardware accessory pack shipped with the hood and check contents.
  • Page 11: Step 4 Mount Template

    Installation Instructions STEP 4 MOUNT TEMPLATE • Align the template with the marks on the ceiling and tape in place. – Be sure the template is oriented correctly, with the front of the hood. • Use a plumb bob to be sure the mounting holes will pro- vide parallel alignment with the countertop below.
  • Page 12: Step 6 Secure Wiring

    Installation Instructions STEP 6 SECURE WIRING STEP 7 SIZE AND INSTALL DUCTWORK • Route house wiring through the ceiling hole and pull a length to reach the hood junction box, approximately 6" below the support. Ceiling Left Side View Support Frames Tape House...
  • Page 13: Step 8 Install Decorative Duct Covers

    Installation Instructions STEP 8 INSTALL DECORATIVE DUCT COVERS Right Side • Slide the lower decorative duct over the installed upper • Pretap or drive decorative screw into the screw holes duct and push to the top. on the support frame. This will make screw installation easier.
  • Page 14: Step 10 Connect Electrical

    Installation Instructions STEP 11 SLIDE DUCT COVER DOWN STEP 10 CONNECT ELECTRICAL Verify that power is turned off at the source. WARNING: If house wiring is not 2-wire with a ground wire, a ground must be provided by the installer. When house wiring is aluminum, be sure to use UL-approved antioxidant compound and aluminum-to- copper connectors.
  • Page 15: Step 12 Install Filters, Finalize Installation

    Installation Instructions STEP 12 INSTALL FILTERS, FINALIZE INSTALLATION Filter Slots • Tip the filter into the lower slots at the rear of the opening. Lift the filter and pull the knob forward until the filter rests on the slots. • Make sure you have engaged the "Clean Filter Reminder Switch"...
  • Page 16 Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram local service in your area, call ® 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.

Table of Contents