Page 5
We are confident that the new hob that you tion standards. Likewise, any internal work on the hob should only be done by BEKO's have purchased will fully satisfy your needs. technical staff, including the change of the flexible supply cable of the appliance.
Page 6
P20770_Maquetación 1 17.03.2014 09:36 Page 12 these may catch fire. Never try to extin- magnet). guish a fire with water! in this event dis- connect the device and cover the flames Always use cookware with a flat, with a lid, a plate or a blanket. smooth base on the induction ele- ments.
Page 7
P20770_Maquetación 1 17.03.2014 09:36 Page 13 WARNING: If the surface is crac- ked, switch off the appliance to avoid the possibility of an electric shock This appliance is not intended to be operated by means of external timer or separate remote control system If the electrical supply is restric- ted, means of all-pole disconnection must be accessible and incorporated in...
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 13 Installation INSTALLATION AND SETUP SHOULD fig. 1 Minimum distan- BE CARRIED OUT BY AN AUTHORISED ce to walls TECHNICIAN ACCORDING CURRENT INSTALLATION STANDARDS. Positioning the hobs To install these models, an opening with the dimensions shown in figure 1 should Important: minimum be cut into the unit's worktop.
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 14 oven, to ensure good operation of the tion, the glass could break when trying countertop. to detach it. A space should be left in front of the furni- To attach the cooking countertop to the fur- ture for evacuation of hot air.
Page 10
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 15 nical service. The input cable should not be in contact either with the body of the hob or with the body of the oven, if the oven is installed in the same unit.
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 17 Use and Maintenance Pilot indicator light Total Zone Function Touch control panel user activated*. instructions - Light (on): Plate selected (ready to be used). CONTROL PANEL ELEMENTS (see fig. 3 - No light (off): Plate not selected (can't be and 4) used).
Page 13
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 18 fig. 4 TURNING THE APPLIANCE ON ACTIVATING PLATES The first time the cooktop is plugged in (or Once the Touch Control is activated with after a power outage), the Block function sensor (1), any plate can be turned on will appear as activated (pilot light 10 on).
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 19 cator if the glass surface of the cooking Blocking cooktop sensors area reaches an elevated temperature. Burn risk exists. When the temperature decreases, the indicator turns off (if the BLOCK FUNCTION cooktop is disconnected), or it will show a if it is still on.
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 20 cooking area. This function is available only in the plates where this symbol appears This function is independently available for each one of the plates. Pot requirements To activate it, select the plate. The decimal For properly using boil control, the pot point will light up.
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 21 A few seconds after the chronometer is Table 1 activated, a third beep will go off indicating MAXIMUM that, from this moment on, the system will Power level OPERATION TIME reduce the energy supplied in order to selected (in hours) maintain a gentle and steady boil.
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 22 1 Select the plate you wish to stop the Timer function timer on by directly touching its corres- (countdown clock) ponding indicator (3). This function facilitates cooking given that 2 Adjust the value of the clock to "--" by you don't have to be present: You can set using the "less"...
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 23 * Do not drag over the glass cookware with Power surges in the network corners or edges that could damage the glass. * The glass will withstand bangs from large The touch control can bear cer- cookware that does not have sharp tain variations in voltage supply admis- edges.
Page 19
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 24 Light soiling When the colour of the glass changes Light, non-sticky, soiling can be cleaned with This does not affect the effectiveness or a damp cloth and a mild detergent or warm, stability of the hob and is generally caused soapy water.
Page 20
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 25 BEKO reserves the pens, do not try and remove the frag- ments with your hands; carefully use right to alter its manuals in any way it tweezers or a knife with a sharp tip (See deems necessary or useful while not alte- fig.
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 26 If something doesn't work Before calling the Technical Service, please check the following possible causes and solutions: Problem Possible cause Solution The induction zones don't get hot Make sure that the base of The cookware is inadequate the cookware is attracted by (it doesn't have a ferromagne- a magnet or use larger cook-...
Page 22
61401274_GB_DE_Maquetación 1 30.05.2012 14:31 Page 27 Fault Possible cause Possible solution The hob suddenly starts to bleep There is a cloth, container Remove any object covering or liquid on the Touch Con- the Touch Control and/or clean any liquid that might trol.