Basic Operating - NPG DVD-T 901H Instruction Manual

Connection DVD
Connection With TV Set
1 .If your TV set bears an AV port, connect this player
to it with the attached audio/video wires and then
set the TV set at AV mode after checking . (shown
as figure®)
2.If your TV set bears S-video terminal , connect this
player to it with S terminal connecting wire
(optional) to for high quality picture . (shown as
figure (2))
3.If your TV set bears a component input port (also
known as chromatic aberration input) , connect
component output terminals of this player and input
terminal of the TV set correspondingly with 3
connecting wires (optional) , and then press "
VIDEO" key on remote controller to switch this
player at YUV mode for vivid picture . (shown as
figure ®)
4.If your TV set bears a component input port and
supports progressive scanning , connect according
to NO.3 then press "VIDEO" key on remote
controller to switch this player at YUV progressive
output mode for better picture.
5.If the TV set will be builtin one or more SCART input
socket. Use the SCART cable to connect between
the DVD receiver and the TV correctly.
Select one group of audio output connections .
* Switch off the power before connecting .
* Turn to system of this player to fit the TV system when playing discs with different systems .(NTSC/PAL/AUTO).
* Just select one group connecting wire among video connecting wire , S-terminal connecting wire , component video
connecting wires to guarantee the pictures'quality .
* Do not connect digital coaxial output terminal of DVD player to analog input terminal of AV player.
* Do not turn on/off frequently , and keep the interval more than 10 seconds .Ground the grounding terminal
* .
HDMI
If the TV has HDMI input ,contact the DVD player and make
the setting as follows:
1) Contact the DVD player to your TV with composite cable
(yellow) ,then press SETUP button on remote control
2) In setup menu, select the HD Output menu, then change the
Mode to 720p or 1080i or 1080p
3) Contact the DVD player to your TV with HDMI
4)
Change Video input on your TV to HDM
Content of the output for each output jack is shown in following
table and differ depending on USER setting/ operation
USER setting/operation
Video outpou HDMI output HDMI
setting setting output
S-Video
Invalid -
(Composite)
Component
Invalid -
(Interlaced)
P-SCAN
Invalid -
(Progressive)
HD off -
720p 720p
HDMI
1080i 1080i
1080p 1080p
I
Content of output for each output jack
S-video Component Video
output output output
480i - 480i
480i 480i 480i
480i 480p 480i
480i 480p 480i
- - -
- - -
- - -

Basic Operating

-4-
Playing
1.Check all the connections before starting the unit, then insert the power plug in AC power supply socket.
2.Press "POWER" key on panel to switch on the power and display logo icon on screen .
3.Press "OPEN/CLOSE" key to eject the disc tray and place the disc on it .(Note : the lettered surface upward).
4.Press the key once more to enter the tray , and CD discs will enter auto play several seconds later; DVD , MP3 etc. with title
directory will enter menu mode . At this time press direction control keys on remote controller to move cursor to the desired
track , then press "ENTER" key to play * Set size of the picture via aspect ratio of the connected TV set
screen referring to "Systen Setup".
Video Output Modes
Switch the video output modes . Connect referring to "Connection With TV Set", then press "VIDEO" key on remote controller to
select output mode . There are 4 for selection :
Play System
Press "PIN" key according to discs to select play system from "NTSC","PAL" and "AUTO" for a good visual effect.
Audio Switch
LWhen playing DVD music disc , press "Audio" key to switch audio channels .
2.When playing discs recorded in multichannel format, press "Audio" key to select from different audio channels . (Just for discs
recorded in multichannel format).
Notes:
·Refer to the owner's manual of the connected TV as well
·When you connect the DVD video player to your TV, be sure to turn off the
power and unplug both units from the wall outlet before making any connection
·If you have a HDMI(with HDCP) equipped monitor or display, you can connections
it to this player using a HDMI cable
·The HDMI connector outputs uncompressed digital video, as well as almost every
kind of digital audio that the player is compatible with, including DVD-Video,
Video CD/SVCD/CD,MP3/WMA/JPEG
·This unit has been designed to be compliant with HDMI(High Definition Multimedia
Interface) Version1.2b depending on the component you have connected. Using a
HDMI connection may result in unreliable signal transfers
·When using HDMI cable, do not connect to other analog video outputs
·Because HDMI is an evolving technology, it is possible that some devices with an
HDMI input may not operate properly with this DVD Video player
·No sound will be output from the HDMI cable if the Digital out is not set to PCM
·If the TV with HDMI doesn't support DTS output decoding when playing
discs, there will be noise during HDMI output.
-5-
DTS CD