Advertisement
Table of Contents
- 1 Table of Contents
- 2 S16T Overview
- 3 Opening the Case
- 4 ODD Cage Removal
- 5 Optical Disk Drive Installation
- 6 Metal Sticker Fitting Instructions
- 7 Optical Drive Bezel Installation
- 8 Hard Drive Installation
- 9 TFT Controls / Menu Operation
- 10 Multi-Format Card Reader & I/O Ports
- 11 Pcb/Cable Reference Diagram
- 12 Touch Panel Software Installation
- 13 VGA Loop Cable
- 14 Micro ATX Standoffs
- 15 Installing VFD/IR Software
- Download this manual
Advertisement
Table of Contents
Related Manuals for Origen ae S16T
Summary of Contents for Origen ae S16T
- Page 1 S1 6T user guide Origen...
-
Page 2: Table Of Contents
We are driven by the passion to produce exceptional products that push technical and aesthetic boundaries to new levels. For more information on all of our products, visit www.origenae.com S16T overview Opening the case ODD cage removal... -
Page 3: S16T Overview
S16T overview These are the main features and controls of the S16T htpc enclosure. Power button Blue LED ring External TFT on/off (under chassis) One piece aluminum chassis 7” TFT touch panel Top panel TFT menu controls Optical disk drive (ODD) bezel... -
Page 4: Opening The Case
Opening the case Remove the thumb screws as indicated. Carefully raise the p anel as shown (about 30mm is enough) pull out to remove. Reverse the procedure to replace. DO NOT force upwards as this could cause damage to the top panel. ODD cage removal Hard drive mount... -
Page 5: Metal Sticker Fitting Instructions
Metal sticker fitting instructions [S14V/S16V] The drive format icon should also be fitted to the bezel before installation. The metal sticker sheet supplied has Blu-ray, HD-DVD or DVD icons, depending on the format being used. Ensure the bezel is free from dirt of grease. Peel and fold back the yellow backing sheet, revealing only the part you wish to use. -
Page 6: Hard Drive Installation
To install drives 1,2 and 3, begin by removing the two thumb screws... To install the 4th drive above the optical drive... *A fifth drive can be installed to the S16T using the HM100 hard drive mount (optional). -
Page 7: Tft Controls / Menu Operation
TFT controls / menu operation The TFT controls are located behind the chassis door. A second TFT on/off button is discreetly located near the power button on the underside of the chassis. To configure the TFT, press menu/set button to bring up the on screen display (OSD). -
Page 8: Multi-Format Card Reader & I/O Ports
Multi-format card reader & I/O ports All the S range cases come fitted with a multi-format card reader and front I/O port PCB which consist of audio in and out, 1394 and two ports. A built- in USB hub powers the front USB ports as well as 2 internal connectors, which are used for the IR controller, VFD or [TFT] touch panel, depending on the model. -
Page 9: Pcb/Cable Reference Diagram
1 - TFT control button PCB This is a general overview illustrating 2 - TFT control (AD) board how the internal PCBs in the S16T 3 - TFT [external] power on/off interconnect. Please refer to your 4 - Main power button PCB... -
Page 10: Touch Panel Software Installation
Touch panel software installation In order to use the touch panel, you must first install the touch panel software from either an install CD or downloaded from our website (www.origenae.com and navigate to support downloads s-series). To begin installation, double >... -
Page 11: Vga Loop Cable
Micro ATX stanoffs If a micro ATX motherboard is to be installed in the S16T, the spacer bolts supplied must be used. Screw the bolts into the two standoffs as indicated. Spacer bolts MUST NOT BE INSTALLED with a full ATX motherboard, as damage could occur. -
Page 12: Installing Vfd/Ir Software
Installing VFD/IR Software Download the latest IR310 installation software from our website, extract the files then follow these steps... Read this notice before installation - The USB (S-IUSB-C2) cable must be connected to USB header pins. - The 5V standby cable must be connected Release the downloaded file in the location Installation the iMONsetup in folder. - Page 13 Select the programs. (iMON is essential and iMEDIAN HD is unessential) Click finish to next setup now. Reboot computer to activate IR310. Please select the iMON PAD remote from the option page. Installation is now completed. Thank you.
- Page 14 Origen Global HQ #209 Baeksan B/D 763-2 Hengsin-Dong Dukyang-Gu Goyang City Gyounggi-Do 412-220 South Korea Website www.origen .com...