Editing The Parameters; Submenu 1.1: Setting Rtc Time Manually; Submenu 1.2: Setting Rtc Date Manually - Nixie Clock IN-18 Blue Dream User Manual

2012
©
2.11 Setting of the LED floor lighting brightness for
night power-down mode
2.12 Setting the LED floor lighting effect
(continuously/fading)
2.13 Setting the time for entering night power-
down mode
2.14 Setting the time for leaving night power-down
mode
2.15 Setting the RTC drift compensation
2.16 Setting the AUX/Buzzer output
Going through the submenu by pressing button 2 or 3
you can reach the value you want to alter. To enter
and edit a submenu button 1 must be pressed
shortly. The chosen value can now be stepped up by
pressing button 2 and down by pressing button 3. The
value will be set
To leave a submenu, button 1 must be pressed
long time (0.5 seconds) and you will return to the main
menu.
To then leave a main menu, button 1 must be
pressed long time (0.5 seconds) and the clock shall
switch back to day display mode or night power-down
mode.

10. Editing the Parameters

Submenu 1.1: Setting RTC Time manually

If this menu is entered, clock (RTC) stops running and
the tubes show the preset time (stored in the RTC). If
the clock is set up to AM/PM mode, nevertheless the
display shows the time in 24-h mode. Also if a DCF or
a GPS receiver is connected, and the clock is set to
GPS or DCF mode the time can be set manually but
will be synchronized later again to the DCF/GPS
signal.
Using button 2 and 3 the chosen digit can be set. To
switch to the next position, button 1 must be pressed.
To confirm this step shifting from digit to digit, the
following digit scrolls through by using the flip over
effect. After the last digit, the first digit shall be enabled
again.
The time of the day shall exactly be written into the
memory, when the submenu 1.1 is left. Therefore the
clock can be set exactly on the dot.
Setup Example:
• The time shall be set to 05:25:30 PM = 17:25:30
o'clock.
• Clock is in day display mode or night power-down
mode.
• Press button 1 long time (0.5 seconds) to enter the
main menu 1.
• Clock stops and displays the current set time.
• Press button 1 (short) to enter the submenu 1.1.
• Press button 2 (to count up) and button 3 (to count
down) to set the first digit (to '1')
• Press button 1 (short) to jump to the second digit
• Press button 2 and button 3 to set the second digit
(to '7')
• Press button 1 (short) to jump to the third digit
by leaving the submenu.
nixiekitworld.com
nixiekitworld.com – Nixie Clock – IN-18 Blue Dream
• Press button 2 and button 3 to set the third digit
(to '2')
• Press button 1 (short) to jump to the fourth digit
• Press button 2 and button 3 to set the fourth digit
(to '5')
• Press button 1 (short) to jump to the fifth digit
• Press button 2 and button 3 to set the fifth digit
(to '3')
• Press button 1 (short) to jump to the sixth digit
• Press button 2 and button 3 to set the sixth digit
(to '0')
• Press button 1 long time (0.5 seconds) to leave
the submenu 1.1.
• Press button 1 long time (0.5 seconds) to leave
the main menu 1.
• Clock starts running in day display mode or night
power-down mode with the set time.
Submenu 1.2: Setting RTC Date
manually
This submenu is similar to submenu 1.1 except that
current date shall be displayed and edited.
During setting date in this menu the clock shall
always
DD.MM.YY.
If a corrupt date is set (e.g. 31.02.2011) the clock
would accept that date. But when leaving the
submenu, the clock checks if the date exists and if
not, the clock corrects it automatically and saves it
(e.g. 28.02.2011).
Setup Example:
• Date shall be set to December, 24th 2012.
• Clock is in day display mode or night power-
down mode.
• Press button 1 long time (0.5 seconds) to enter
the main menu 1.
• Clock stops and displays the current set time.
• Press button 2 once to reach submenu 1.2
• Press button 1 (short) to enter the submenu 1.2.
• Press button 2 (to count up) and button 3 (to
count down) to set the first digit (to '2')
• Press button 1 (short) to jump to the second digit
• Press button 2 and button 3 to set the second
digit (to '4')
• Press button 1 (short) to jump to the third digit
• Press button 2 and button 3 to set the third digit
(to '1')
• Press button 1 (short) to jump to the fourth digit
• Press button 2 and button 3 to set the fourth digit
(to '2')
• Press button 1 (short) to jump to the fifth digit
• Press button 2 and button 3 to set the fifth digit
(to '0')
• Press button 1 (short) to jump to the sixth digit
• Press button 2 and button 3 to set the sixth digit
(to '9')
• Press button 1 long time (0.5 seconds) to leave
the submenu 1.2.
display date in the arrangement
5