Page 3
CAREFULLY READ THIS MANUAL AND KEEP IT FOR FURTHER REFERENCES INSTALLATION OF THIS APPLIANCE MUST BE DONE BY A QUALIFY CERTIFIED TECHNICIAN AND IN CONFORMITY WITH THE OWNER'S MANUAL GUIDE GIVEN WITH THIS APPLIANCE. THE INSTALLATION MUST BE IN AGREEMENT WITH LOCAL AND NATIONAL REGULATIONS APPLICABLE FOR SOLID FUEL BURNING APPLIANCES AND CONNEX EQUIPMENT...
WARNING Before installing, please take a few minutes to read this handbook. Keep it in a sure place and easily reachable for future references. Not following these instructions could be a cause of property damages, injuries or death. If this appliance is not properly installed, it could cause fire damages to the property, injuries and death.
Page 5
If the appliance starts to blush, it's because it is too charged. Do not add fuel. Immediately close the doors and the air intake of the appliance until everything becomes normal again. Do not load the appliance beyond the firebricks height. Ashes must be evacuated frequently, put in a steel container provided with a tight cap and be placed outside at once.
- Do not use the appliance when a glass is broken or damaged. - Do not build the fire too close of the glasses. - Keep the doors closed when using the appliance. - Do not connect the Mystere with a chimney or a flue serving another heating appliance...
Only use approved chimneys of the same dimensions as the appliance exit. Therefore, you should use 6 inches diameter chimneys for your Mystere. Chimneys must be tested upon the CAN/ULC S629 M87. The Mystere wood appliance can be installed onto a masonry chimney following the ULC S635, ULC S640 and UL 1777 norms.
ERTICAL INSTALLATION INSIDE A MASONRY CHIMNEY The Mystere wood appliance must be installed in accordance with the applicable local laws or the ULC S635, ULC S640, NFPA211 ( USA ) norms. Install the chimney following the manufacturer’s instructions. XTERIOR VERTICAL INSTALLATION...
ERTICAL INSTALLATION ON A CATHEDRAL ROOF The Mystere wood appliance must be installed in accordance with the applicable local laws or the CAN/CSA-B365, NFPA211 ( USA ) norms. Install chimney following manufacturer’s instructions. ROSS STYLE INSTALLATION The Mystere wood appliance must be installed in accordance with the applicable local laws or the CAN/CSA-B365, NFPA211 ( USA ) norms.
ERTICAL INSTALLATION The Mystere wood appliance must be installed in accordance with the applicable local laws or the CAN/CSA-B365, NFPA211 ( USA ) norms. Install the chimney following the manufacturer’s instructions.
CLEARANCES Due to its reduced clearances, this appliance occupies a minimum of space in the room where it is installed. No matter where you install it, this appliance will perfectly complete your decoration by its originality and its heat. This appliance only needs 8 inches clearance at its back and 12 inches from the lateral walls when installed with a single wall pipe and a certified CAN/ULC S641 heat shield.
SEATING You must install a fireproof plate under the appliance, which must exceed it of 18 inches at the front, of 8 inches at the sides and of 8 inches at the back. ***Use only non-combustible materials such as ceramics, marble or granite.
FANS AND THERMODISC The 115 volts fans must be screwed with the grids under the ventilation conduct. The protection thermo disc box must be on the back of the ventilation conduct. Plug the terminal. When the appliance is in function, the heat reaching a temperature of 120 activates the thermo disc.
Avoid cleaning with abrasives or when the glass is hot. The Mystere wood appliance is provided with an ashtray under the door. To empty it, remove the steel cap (in the middle of the appliance) and glide the ashes into the ashtray.
Before lighting the first fire, clean the gold plated surfaces using a very soft rag moistened with water. Do not use a paper towel to clean it. If they are not erased before the first fire, the fingerprints and other marks could stain these surfaces permanently. In case of a glass replacement: Remove the screws that retain the glasses and then, the fragments of glasses.
J. A. ROBY. Failure of any components which is attributed to poor maintenance, is not warrantable and will not be covered by this policy. J.A. ROBY neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product.