Black & Decker JS650L Instruction Manual page 12

c) Use clamps or another practical way to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body leaves it unstable
and may lead to los of control.
d) Keep blades sharp. Dull blades may cause the saw to swerve or stall under
pressure.
e) When cutting pipe or conduit ensure that they are free from water, electrical
wiring, etc.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay
on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles
away from face and body.
CAUTION: Wear appropriate hearing protection during use. Under some
conditions and duration of use, noise from this product may contribute to hearing loss.
The label on your tool may include the following symbols.
V................volts
Hz..............hertz
min ............minutes
..........direct current
............ Class II Construction
..............safety alert symbol
mW............milliwatts
II ................Class II Laser
SAFETY INSTRUCTIONS - LASERS
DANGER: Laser Radiation, avoid direct eye exposure, serious eye injury can result.
• Do not use optical tools such as a telescope or transit to view the laser
• Position the laser so unintentional eye contact will be avoided.
• Do not operate the laser around children or allow children to operate the laser.
• Do not disassemble. Modifying the product in any way can increase the risk of laser
radiation.
WARNING: Use of controls or adjustments or performance of procedures other than
those specified in this manual may result in hazardous laser radiation exposure.
• Do not adjust the laser on the saw unit, when the saw is plugged in.
• Do not operate in explosive atmospheres, such as in the presence of flammable liquids,
gases, or dust.
• Use only with the specifically designated batteries in laser. Use of any other batteries may
create a risk of fire.
• Store idle product out of reach of children and other untrained persons. Lasers are
dangerous in the hands of untrained users.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one laser, may create a risk of injury when used on
another laser.
• Repairs and servicing MUST be performed by a qualified repair facility. Repairs
performed by unqualified personnel could result in serious injury.
A ..............amperes
W ..............watts
....alternating current
n o ............no load speed
........earthing terminal
.../min ......revolutions or
reciprocations per minute
nm ..............wavelength in nanometers
beam.
22
Features - JS650L
1. Jig Saw On/Off switch
2. Lock-on button
3. Variable Speed control knob
4. Saw blade clamp lever
5. Saw blade support roller
6. Saw blade
7. Shoe plate
8. Shoe plate locking knob
9. Saw blade storage compartment
10. Laser
11. Laser On/Off button
12. Laser adjustment screw
13. Finish Control System orbital selector
14. Dust blower
For your convenience and safety, the following labels are on the laser.
Para su comodidad y seguridad, el láser incluye las siguientes etiquetas.
WARNING/ ADVERTENCIA
To reduce the risk of injury, user
must read and understand instruction
manual. Use (2) AA size batteries.
Para reducir el riesgo de lesiones, el
usuario debe leer y entender el manual
de instrucciones. Utilice (2) bater!as AA
588808−01
Use with
compatible
Type 1
B&D Jig
3V DC −−−
Saws.
ON/OFF
LISTED 406A
COMPLIES WITH 21CFR PARTS 1040.10 AND
1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO
LASER NOTICE NO.50, DATED JULY 26,2001.
LASER RADIATION DO NOT STARE INTO BEAM LASER RADIATION DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT CLASS 2 LASER PRODUCT
PER EN60825- 1:11994+AII+A2 PER EN60825 - 1 :11994+AII+A2 Pmax- 2.8mW Pmax - 2.8mW, ,
Black & Decker
(U.S.) Inc., Towson,
MD 21286 U.S.A.
1−800−54−H OW−TO Made in China
A
3
10
1
2
11
12
4
8
7
13
5 14
6
=633 - 6 70nm =633 - 670nm
B
8
23
9