Sony DCR-TRV738E Service Manual page 109

3-1-2. Precautions on Adjusting
Note1: Before performing the adjustments, check the data of page: 0,
address: 10 is "00". If not, set data: 00 to this address.
1) The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to "VCR or
PLAYER" or set the "Forced VTR Power ON mode" using the
adjustment remote commander (Note2).
To set to the Camera mode, set the power switch to "CAMERA"
or set the "Forced Camera Power ON mode" using the
adjustment remote commander (Note3).
After completing adjustments, be sure to exit the "Forced VTR
Power ON Mode" or "Forced Camera Power ON Mode".
(Note4)
2) The front panel block (SI-032 board (Microphone amp., remote
commander receiver), FP-411 flexible (MIC jack, Head phone
jack, LANC jack, MF photo sensor)) must be assembled for
connecting the adjusting remote commander.
To remove it, disconnect the following connector.
VC-278 board CN1116 (30P 0.5mm)
3) As removing the cabinet (R) assembly (removing CN1110 of
the VC-278 board) means removing the lithium 3V power
supply (BT001 on the CF-2500 block), data such as date, time,
user-set menus will be lost. After completing adjustments, reset
these data.
But the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the lithium 3V
power supply is removed. (Refer to "5-4.Service Mode" for
the self-diagnosis data and the data on history of use.)
4) The cabinet (R) assembly (CF-2500 block, LCD bock) need
not be connected to operate the VTR block. (Use the adjustment
remote commander, to operate the VTR block.) When removing
the cabinet (R) assembly, disconnect the following connector.
1. VC-278 board CN1110 (22P, 0.5mm)
2. VC-278 board CN1106 (20P, 0.8mm)
5) The memory stick connector is need not be connected. To
remove it, disconnect the following connector.
VC-278 board CN1105 (10P, 0.5mm)
6) The viewfinder block is need not be connected. To remove it,
disconnect the following connector.
VC-278 board CN7001 (20P, 0.5mm)
7) The lens block (CD-358 board) need not be connected. To
remove, disconnect the following connectors.
1. VC-278 board CN1501 (24P, 0.5mm)
2. VC-278 board CN1551 (24P, 0.5mm)
8) By setting the "Forced VTR Power ON mode" or "Forced
Camera Power ON mode", the video section can be operate
even if the cabinet (L) assembly (SS-1380 block) has been
removed. When removing the cabinet (L) assembly, disconnect
the following connector.
1. VC-278 board CN1109 (12P 0.8mm)
DCR-TRV738E/TRV740/TRV740E/TRV840
Note2: Setting the "Forced VTR Power ON" mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button.
The above procedure will enable the VTR power to be
turned on with the cabinet (L) assembly (SS-1380 block)
removed.
After completing adjustments, be sure to exit the "Forced
VTR Power ON mode".
Note3: Setting the "Forced Camera Power ON" mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button.
The above procedure will enable the camera power to be
turned on with the cabinet (L) assembly (SS-1380 block)
removed.
After completing adjustments, be sure to exit the "Forced
Camera Power ON mode".
Note4: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button.
3) Select page: 0, address: 01, and set data: 00.
5-43