Advertisement
F F F F F
IND
IND
OUT
OUT
MORE
MORE
IND OUT
IND
IND
OUT
OUT MORE
MORE
MORE
. . . . .
ON
ON
THE
THE
WEB
WEB
ON
ON
ON THE
THE
THE WEB
WEB
WEB
W I L B U R C U R
W I L B U R
W I L B U R
W I L B U R
W I L B U R
C U R
C U R
C U R T I S . C O M
C U R
T I S . C O M
T I S . C O M
T I S . C O M
T I S . C O M
Models Included
• • • • • D500GT
• • • • • D500GT/H
WARNING HOT LIQUID,
Scalding may occur.
Avoid splashing.
CAUTION:
CAUTION: Please use
CAUTION:
CAUTION:
CAUTION:
this setup procedure
before attempting to use
this brewer. Failure to follow the
instructions can result in injury or
the voiding of the warranty.
CAUTION:
CAUTION:
CAUTION:
CAUTION:
CAUTION: DO NOT
connect this brewer to
hot water. The inlet valve
is not rated for hot water.
C
ISO 9001 REGISTERED
WILBUR CURTIS COMPANY
Montebello, CA 90640
W W W W W
ILBUR
ILBUR
ILBUR
ILBUR
ILBUR
D500 Generation 3 - Airpot Brewer Instructions
Important Safeguards/Conventions
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance
should be performed by an authorized Wilbur Curtis service center.
• Do NOT immerse the unit in water or any other liquid
• To reduce the risk of fire or electric shock, do NOT open top or rear panel. No user serviceable parts inside. Repair should
be done only by authorized service personnel.
• Keep hands and other items away from hot parts of unit during operation.
• Never clean with scouring powders, bleach or harsh implements.
Conventions
Conventions
Conventions
Conventions
Conventions
W W W W W ARNINGS –
ARNINGS –
ARNINGS –
ARNINGS – T T T T T o help a
o help avoid personal injur
o help a
o help a
ARNINGS –
o help a
Important Notes/Cautions – from the factory
Important Notes/Cautions – from the factory
Important Notes/Cautions – from the factory
Important Notes/Cautions – from the factory
Important Notes/Cautions – from the factory
Sanitation
Sanitation
Sanitation
Sanitation
Sanitation
Requirements
Requirements
Requirements
Requirements
Requirements
Y Y Y Y Y our Curtis
our Curtis
our Curtis
our Curtis ADS System is F
our Curtis
ADS System is F
ADS System is Factor
ADS System is F
ADS System is F
Following are the Factory Settings for your D500GT Airpot Coffee Brewing System:
• Brew
• Brew
• Brew T T T T T empera
• Brew
• Brew
empera
empera
emperature = 200°F
empera
ture = 200°F
ture = 200°F
ture = 200°F
ture = 200°F
• Brew Volume = Set to dispensing vessel requirements (2.2 liters)
• Brew Volume = Set to dispensing vessel requirements (2.2 liters)
• Brew Volume = Set to dispensing vessel requirements (2.2 liters)
• Brew Volume = Set to dispensing vessel requirements (2.2 liters)
• Brew Volume = Set to dispensing vessel requirements (2.2 liters)
Generally there will never be a reason to change your ADS programming. However, should you need to make slight adjustments
to meet your brewing needs, programming instructions are provided later in this manual.
System Requirements:
• • • • • W W W W W a a a a a ter Source
ter Source
ter Source
ter Source
ter Source 20 – 90 PSI (Minimum Flow Rate of 1 GPM)
• Electrical:
• Electrical:
• Electrical:
• Electrical:
• Electrical: See attached schematic for standard model or visit www.wilburcurtis.com for your model.
Equipment to be installed to comply with applicable federal, state, or local plumbing/electrical codes having jurisdiction.
SETUP STEPS
SETUP STEPS
SETUP STEPS
SETUP STEPS
SETUP STEPS
The unit should be level (left to right and front to back), located on a solid counter top. Connect a water line from the water filter to the
brewer. NOTE: Some type of water filtration device must be used to maintain a trouble-free operation. (In areas with extremely hard
water, we suggest that a sedimentary and taste & odor filter be installed.) This will prolong the life of your brewing system and
enhance coffee quality.
The National Sanitation Foundation requires the following water connection:
1. A quick disconnect or additional coiled tubing (at least 2x the depth of the unit) so that the machine can be moved
for cleaning underneath.
2. In some areas an approved backflow prevention device may be required between the brewer and water supply.
1. A 3/8" NPT x 1/4" Flare elbow has been supplied for water line connection. Use tubing sized sufficiently to provide a minimum of
1.0 GPM.
2. Connect the unit to an appropriate electrical power circuit.
3. Turn on the toggle (STANDBY/ON) switch behind the unit. The heating tank will start to fill. When the water level in the tank rises
to the correct volume, the heating elements will energize automatically. With ADS Systems there is no danger of element burnout
caused by an empty tank.
4. The heating tank will require 20 to 30 minutes to reach operating temperature (200°F) as indicated by the READY-TO-BREW
indicator light.
5. Prior to brewing, dispense 12 ounces of hot water through the hot water faucet.
6. Brew a cycle of at least 12 ounces, to purge the water lines of any air that may be trapped after filling.
BREWING INSTRUCTIONS
BREWING INSTRUCTIONS
BREWING INSTRUCTIONS
BREWING INSTRUCTIONS
BREWING INSTRUCTIONS
1. Brewer should be ON (Confirm at rear toggle switch, then press ON/OFF button). Ready-to-Brew should be displayed.
2. Place empty airpot on deck.
3. Place filter in brewcone.
4. Pour ground
coffee into
brewcone.
FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO
C C C C C
C C C C C
URTIS
URTIS
OMP
OMP
URTIS
URTIS
URTIS
OMPANY
OMP
OMP
void personal injur
void personal injur
void personal injury y y y y
void personal injur
actor
actor
actory Pre-Set and Read
actor
y Pre-Set and Read
y Pre-Set and Read
y Pre-Set and Read
y Pre-Set and Ready to Go... Right out of the Carton.
y to Go... Right out of the Carton.
y to Go... Right out of the Carton.
y to Go... Right out of the Carton.
y to Go... Right out of the Carton.
5. Position
brewcone
into brew
rails.
WWW.WILBURCURTIS.COM
, I , I , I , I , I
. . . . .
ANY
ANY
NC
NC
ANY
ANY
NC
NC
NC
6.Press Brew
button.
1
Advertisement
