Preface............................V Part I: IAD Gateway Overview....................1.1 Overview........................1.2 Software Specifications ....................1.3 Hardware Specifications....................5 Part II: Start-UP ........................10 2.1 Software Installation Guide..................12 2.1.1 Default Settings of IAD gateway................12 2.1.2 Additional Installation Requirements............... 12 2.1.3 Essential Configuration via Web Management interface........2.1.4 Essential Configuration via Telnet Command Line interface.........
Page 3
3.4 Upgrade Your IAD....................... 46 3.4.1 Upgrade via Web management interface..............46 3.4.2 Upgrade via Telnet Command interface..............49 3.5 IAD 162 PSTN Line Application................53 3.5.1 PSTN Outgoing Call....................53 3.5.2 PSTN Incoming Call....................53 3.5.3 VoIP Outgoing Call....................53 3.5.4 VoIP Incoming Call....................
161/162 VoIP Gateway. Revision History: Versio Date Author Modified Contents Sep., Sabrina Revision for IAD 161 162 SIP Gateway. 2004 Dec., 4 , 2004 Eason Add “Prefix” function in CLI and Web Management Interface. Modify the PSTN line application.
IAD Gateway User Manual Part I: IAD Gateway Overview This part introduces the software/hardware specifications and default settings of the IAD Gateway. - 1 -...
IAD Gateway User Manual 1.1 Overview T he IAD 161 is a one-port telephone extension and three ports SOHO Router to IP network gateway. It provides Data transfer by 10/100Mbps, telephone services and T.38 fax over IP network with easily operation and configuration.
IAD Gateway User Manual 1.2 Software Specifications IAD Gateway Features Provide Voice over IP and Fax over IP features. SIP RFC 3261 compliance Built-in NAT/IP sharing function Provided call features: Hold, forward and transfer Automatic FAX detection (Support T.38 protocol) ...
Page 10
IAD Gateway User Manual VAD (Voice Activity Detection) CNG (Comfort Noise Generation) G.168/165-compliant adaptive echo cancellation Dynamic Jitter Buffer Bad Frame Interpolation Voice/DTMF Gain Settings System Monitoring System status (WAN, LAN, TEL, Status, Power) ...
Four 10/100 Base-T Ethernet RJ-45 ports (Auto LAN MDI/MDIX). Input AC 100V-240V, Output DC 12V. One/Two RJ11 Telephone Port (IAD 161/162). Special Housing The plastic housing can be adjustable by manual (Vertical type or Horizontal type) ...
Page 12
IAD Gateway User Manual Front Panel The LEDs on the front panel indicate the operational status of the Gateway. Power (Green): Light on: IAD is connected with power adapter correctly and power on. Light off: IAD is not connected with power adapter correctly or not power on.
Page 13
IAD Gateway User Manual Light Blanking: IAD is under Proxy mode and not successfully register to Proxy. TEL (Orange): Light Blinking: IAD IP side has incoming call. Light On: IAD IP side is in communication. Light Off: IP Line of IAD is in standby mode. ...
Page 14
IAD Gateway User Manual Ethernet Port: Ethernet port is for connecting VoIP Gateway to network, transmit rate supports 10/100 Base-T. Ethernet connector ( LAN/WAN ) TEL Port: RJ-11 connector, IAD interface to connect analog phone sets or trunk port of PABX. ...
IAD Gateway User Manual 2.1 Software Installation Guide This guide covers all essential configurations under different application, user can follow steps below to configure basic items to run IAD gateway. 2.1.1 Default Settings of IAD gateway WAN IP Parameters ...
Page 19
IAD Gateway User Manual In addition to the contents of your package, there are other hardware and software requirements you need before you can install and use your IAD Gateway. These requirements include: 1. A computer with an Ethernet NIC (Network Interface Card) installed.
IAD Gateway User Manual Once your PC has got an IP from IAD, you may connect IAD via WEB browser to do more configurations. The default LAN IP address of IAD is “192.168.123.123”; please input this IP address on web browser to connect with web management interface.
Page 21
IAD Gateway User Manual Configuration Data screen, click the [Commit] button. In the Commit Configuration Data screen will Display [Commit to Flash OK!], when IAD finished committing data. Step 2. Click [Reboot System] on the navigation panel. In the IAD Gateway screen, click the [Reboot] button.
Page 22
IAD Gateway User Manual Step 3. Close the current browser windows and launch your web browser again. - 16 -...
Page 23
IAD Gateway User Manual 2.1.3.2 Setup Network (1) Fixed IP To configure the VoIP Gateway IP address, please click [Network Interface] on the navigation panel. In the Network Interface screen, type a new IP address, subnet mask and the default routing gateway (e.g.
Page 24
IAD Gateway User Manual (2) DHCP Click [Network Interface] on the navigation panel. In the Network Interface screen, enable the DHCP function if you are using the cable modem or DHCP server and click the [OK] button. - 18 -...
Page 25
IAD Gateway User Manual (3) PPPoE Click [PPPoE Configuration] in the navigation panel and open the [PPPoE Configuration] Screen. Device: Set PPPoe function to be On or Off. User Name: Set PPPoE authentication User Name. Password: Set PPPoE authentication password. Reboot After Remote Host Disconnection: Enable/Disable auto reboot after PPPoE disconnection...
Page 26
IAD Gateway User Manual 2.1.3.3 Application mode-Proxy/Peer-to-Peer Mode After setting IP address, user must assign IAD to work under Proxy mode or Peer-to-Peer mode. If there is no Proxy, please set your IAD as Peer-to-Peer Mode. 2.1.3.3.1 Proxy mode Proxy mode means that there will be an intermediate Proxy Server between IAD Gateway and the remote entity.
Page 27
IAD Gateway User Manual 2.1.3.3.2 Peer-to-Peer Mode Peer-to-Peer Mode allows users to call other VoIP devices without the proxy server. When in Peer-To-Peer mode, IAD Gateway use Phone Book, which will dial predefined phone number, and press “#” (optional, to accelerate the dial) as end of dial.
Page 28
IAD Gateway User Manual Step 2. Configure Phone Book in the IAD Gateway. Click [Phone Book] on the navigation panel. In the Phone Book screen, enter the Index, Name, IP address and e164 (phone number) of the destination and click the Add Data button. - 22 -...
IAD Gateway User Manual 2.1.4 Essential Configuration via Telnet Command Line interface This section describes how to setup IAD via Telnet command line interface. Please follow procedures below to configure essential items before you use IAD gateway. 2.1.4.1 Save Data and Reboot After any configuration has been made, user has to save all data and reboot system to make configurations take effect.
Page 31
IAD Gateway User Manual (2) DHCP usr/config$ ifaddr –dhcp 1 In this case is to enable DHCP mode of IAD, once IAD reboot system, it will automatically capture IP from DHCP server. (3) PPPoE Step 1. To Set PPPoE mode, please use [pppoe] command: usr/config$ pppoe –dev 1 (PPPoE used) usr/config$ pppoe –open (PPPoE open) Step 2.
Page 32
IAD Gateway User Manual Step 4. Commit and reboot IAD. usr/config$ commit usr/config$ reboot Step 5. When IAD successfully establish PPPoE connection, use command [pppoe -print] to see detail information. For example: usr/config$ pppoe -print PPPoE adapter information Device : Enabled Status : Ready User name...
Page 33
IAD Gateway User Manual 2.1.4.3.1 Proxy mode Proxy mode means that there will be an intermediate Proxy Server between IAD Gateway and the remote entity. While operating at this mode, IAD Gateway will first register to the Proxy Server located at the ISP side. For the following operation, it sends the INVITE message to the Proxy Server once you initiate a session.
Page 34
IAD Gateway User Manual successfully registered to Proxy server. Note: 1. Please contact with your Proxy vendor to obtain user account information. 2. If no need to enter password, user also has to set security information, please set “name” the same with line number. 2.1.4.3.2 Peer-to-Peer Mode Peer-to-Peer Mode allows users to call other VoIP devices without the proxy server.
Page 35
IAD Gateway User Manual When adding a record to Phone Book, user does not have to reboot the machine, and the record will be effective immediately. 2.1.4.3.3 Hotline Mode The Hotline Mode is applied in limited two peers. User just picks up the phone set and then hears ring back tone or dial tone depended on configurations of destination device.
IAD Gateway User Manual 2.1.4 Essential Configuration via Installation Wizard Installation Wizard is a friendly software tool that can provide you an easy way to configure your WellTech VoIP devices. You only need to Input the MAC address of your product and Click [Search Device]; you can configure your VoIP device without changing your PC’s setting.
IAD Gateway User Manual 2.1 Special Housing Installation Guide adjustable IAD has special housing for vertical or horizontal type. Please follow procedures as below to change type you like. 2.1.1 Horizontal Type 2.1.1.1 Insert stand board on one side. 2.1.1.2 Insert the other stand board on the other side.
Page 38
IAD Gateway User Manual Finally IAD can stand as horizontal type. - 32 -...
IAD Gateway User Manual 2.1.2 Vertical Type 2.1.2.1 Insert stand board on one side. 2.1.2.2 Insert the other stand board on the same side. 2.1.2.3 Finally IAD can stand as vertical type. - 33 -...
IAD Gateway User Manual Part III: Special Applications and Features This part explains how to configure IAD Gateway under special application mode, such as behind NAT, and how to upgrade firmware. - 34 -...
IAD Gateway User Manual 3.1 Behind IP-Sharing 3.1.1 IP Sharing Configuration 3.1.1.1 One IAD Gateway behind IAD This application is only for the user who is using the IP Sharing device. It is said Gateway is connected behind IP Sharing. The IP Sharing Device must support the DMZ or Virtual server functions such as ADSL network.
Page 42
IAD Gateway User Manual messages from WAN have to completely pass forward to the LAN. It mean that if the IAD Gateway is assigned a virtual fixed IP Address such as 192.168.1.5, IP Sharing device must forward the VoIP message to 192.168.1.5. - 36 -...
Page 43
IAD Gateway User Manual Please see following for example: >Advanced setting > NAT setting > DMZ Host setting DMZ Host setting ▣ Activate DMZ Host IP: 192.168.1.5 Step 6. Configure the IAD Gateway IP address for IP Sharing Mode. Click [Network Interface] on the navigation panel.
Page 44
IAD Gateway User Manual Step 8. Click [Commit Data] on the navigation panel. In the Commit Configuration Data screen, click the Commit button. In the Commit Configuration Data screen will Display [Commit to Flash OK!], when IAD finished committing data. Step 9.
Page 45
IAD Gateway User Manual 3.1.1.2 More than one IAD behind the same IP Sharing Device Assign an IP address to each IAD using fixed address. Enable the IP Sharing function for each set using following command. Fixed IP Address – usr/config$ ifaddr –ipsharing 1 “public IP of IP Sharing”...
Page 46
IAD Gateway User Manual 192.168.1. 5061 5061 192.168.1. 26384 26384 192.168.1. 26394 26394 - 40 -...
Page 47
IAD Gateway User Manual Note: With Dynamic WAN IP Address, when the WAN IP is changed, we need to change the external IP of IAD Gateway using above command. Different Vendor’s Router will have different appearance of setting. Once you set the DMZ Host, you don’t need to configure the Port Forwarding and vice versa.
IAD Gateway User Manual 3.2 NAT mode (PPPoE) Step 1. Set PPPoE mode, using [pppoe –dve 1], input the user id & password provided by your ISP, using [pppoe –id –pwd], reboot the device after disconnection, using [pppoe –reboot 1] usr/config$ pppoe –dve 1 (PPPoE used) usr/config$ pppoe –open (PPPoE open) usr/config$ pppoe –id 123@hinet.net (PPPoE login account)
Page 49
IAD Gateway User Manual usr/config$ ifaddr -print Internet address information LAN IP address : 192.168.123.123 WAN IP address : 192.168.13.71 Subnet mask : 255.255.248.0 Default gateway : 192.168.8.254 NAT enabled : ON DHCP startup : OFF SNTP : mode=1 server 168.95.195.12 time zone : GMT+8 cycle=1024 mins IPSharing...
IAD Gateway User Manual 3.3 Call Hold, Transfer and Forward Gateway provides call features including call hold, transfer and forward. Please be noted that both calling and called site have to support this feature. For call forward function, it only works under Proxy mode. Of course, Proxy must support these call features, too.
IAD Gateway User Manual 3.3.3.1 No response/ Answer: While no one answers the call, incoming call will be forwarded to the assigned number. Activate: *75 [Forward No.] # Deactivate: #75# 3.3.3.2 Busy Forward: While line is engaged or phone set is been off-hook, incoming call will be forwarded to the assigned number.
IAD Gateway User Manual 3.4 Upgrade Your IAD 3.4.1 Upgrade via Web management interface 3.4.1.1 Before start Step 1. Please confirm Host PC, which is installed as TFTP / FTP server and is in available network. Step 2. Note down your current configurations,...
Page 53
IAD Gateway User Manual Step 2. After upgrade finished, on screen will display [Please issue FLASH CLEAN to consist software version.] information. - 47 -...
Page 54
IAD Gateway User Manual Step 3. Click [Flash Clean] on the navigation panel. In the Flash Clean screen, click the [CLEAN] button. Step 4. In the Flash Clean screen to Display [Flash cleaned!! Please reboot - 48 -...
IAD Gateway User Manual your system!!], when Flash Clean Ok. Step 5. Click [Reboot System] on the navigation panel. In the Reboot IAD Gateway screen, click the [Reboot] button. It will take 40 seconds to reboot. Step 6. Close the current browser windows and launch your web browser again.
Page 56
IAD Gateway User Manual usr/config$ rom ROM files updating commands Usage: rom [-print] [-app] [-boot] [-dsptest] [-dspcore] [-dspapp] [-ht] [-method used] [-boot2m] -s TFTP/FTP server ip -f filename rom -print -print show versions of rom files. (optional) -app update main application code(optional) -boot update main boot code(optional) -boot2m...
Page 57
IAD Gateway User Manual Note: Most of all, the Rom file needed to get upgrade is App or Boot2m. Please check the exact Rom file before doing download procedure. -s: To specify TFTP server’s IP address when upgrading ROM files. -f: To specify the target file name, which will replace the old one.
Page 58
IAD Gateway User Manual usr/config$ flash –clean - 52 -...
IAD Gateway User Manual 3.5 IAD 162 PSTN Line Application 3.5.1 PSTN Outgoing Call 3.5.1.1 Make PSTN call from TEL Phone set Default TEL line is intended to make IP call, if user wants to make a call via PSTN line, please dial “*#”, then user will hear dial tone from PSTN side. The dial tone between IP side and PSTN are different.
IAD Gateway User Manual 3.5.4 VoIP Incoming Call When user is communicating with PSTN side with TEL Phone set, IAD can’t have VoIP incoming call. - 54 -...
IAD Gateway User Manual 4.1 Login and welcome screen Step 1. Start your web browser. Step 2. Launch your web browser and enter [192.168.123.123] (the default IP address of the LAN port) in the Location or Address field. Press Enter. Step 3.
IAD Gateway User Manual 4.2 Save and Reboot Click OK at the end of every configuration page to confirm your changes. All configurations will not take effect before reboot system. Please remember to do [Commit Data] to save all configuration then [Reboot System] to reboot IAD.
IAD Gateway User Manual 4.3 Web Management Configuration 4.3.1 Network Interface Click [Network Interface] in the navigation panel and open the Network Interface Screen. LAN IP Address: Set LAN IP Address of IAD (range: 192.168.1.1- 192.168.254.254) WAN IP Address: Set WAN IP Address of IAD Subnet Mask: Set the Subnet Mask of IAD Default routing gateway:...
Page 65
IAD Gateway User Manual IP Sharing: Enable it if IAD is behind IP Sharing router. UPnP: Enable it if IP sharing or NAT device supports UPnP function so that no need to configure IP sharing or IAD when IAD is behind NAT device. IP Sharing Server Address: Set Public IP Address of IP Sharing router for IAD to work behind IP sharing.
IAD Gateway User Manual 4.3.2 SIP Information Screen Click [SIP Configuration] in the navigation panel and open the SIP Information Screen. Run Mode: Select IAD to work under Peer-to-Peer mode or Proxy mode. Primary Proxy IP Address: Set primary Proxy IP Address or URL address (Domain Name Server must be configured.
Page 67
IAD Gateway User Manual and password for registering. If password is no need, please set user name the same as line number or IAD won’t register successfully. Line Password: set password for registering. SIP Port: set SIP UDP port. RTP Port: set RTP port for sending voice data.
IAD Gateway User Manual 4.3.3 System Configuration Click [System Configuration] in the navigation panel and open the [System Configuration] Screen. Keypad DTMF Type: set DTMF type. User can select DTMF type IAD transmits. RFC2833 Payload Type: change RFC2833 Payload type. This is for special request from the other site, if RFC2833 payload types of 2 sites are different, it may cause some problem of connection.
IAD Gateway User Manual 4.3.4 PPPoE Configuration Screen Click [PPPoE Configuration] in the navigation panel and open the [PPPoE Configuration] Screen. Device: Set PPPoe function to be On or Off. User Name: Set PPPoE authentication User Name. Password: Set PPPoE authentication password. Reboot After Remote Host Disconnection: Enable/Disable auto reboot after PPPoE disconnection...
IAD Gateway User Manual 4.3.5 Voice Configuration Screen Click [Voice Configuration] in the navigation panel and open the [Voice Configuration] Screen. Codec Priority: set codecs priority in order. Please notice that user can set from 1 to 5 codecs as their need. For example, user can only set first priority as G.723.1, and set the others as x, that means only G.723.1 is available.
IAD Gateway User Manual 4.3.6 Phone Configuration Screen Click [Phone Configuration] in the navigation panel and open the [Phone Configuration] Screen. For tone simulation, IAD Gateway adopts dual frequencies as traditional telephone does. If users want to have their own call progress tone, they can change the value of tones.
Page 72
IAD Gateway User Manual tone Tone ON/OFF: 0 ~ 8000 (Unit: ms) Ring Back Tone: Set ring back tone parameters. Busy Tone: Set busy tone parameters. Dial tone: Set Dial tone parameters. Low(frq) : Frequency value of Low frequency ...
IAD Gateway User Manual 4.3.7 Support Configuration Screen Click [Support configuration] in the navigation panel and open the [Support Configuration] Screen. T.38 FAX: enable/disable FAX function. If user wants to fax with IAD gateway, this function must be enabled. - 67 -...
IAD Gateway User Manual 4.3.8 Phone Book Configuration Click [Phone Book Configuration] in the navigation panel and open the [Phone Book] Screen. Add Data: User can specify 10 sets of phone book via Web Management Interface. Please input index, Name, IP Address and E.164 number of the destination device.
IAD Gateway User Manual 4.3.9 Prefix Configuration Screen Click [Prefix configuration] in the navigation panel and open the [Prefix Drop/Insert Configuration] Screen. Index: Setting the index number for prefix record (max 30 record). Prefix: Setting the prefix number of the whole numbers that could be into this VoIP gateway (1~20 digits).
IAD Gateway User Manual 4.3.10 DSCP Configuration Screen Click DSCP Configuration in the navigation panel and open the DSCP Configuration Screen. Set Signal or RTP Packet DSCP value: Assured Forwarding (AF) PHB: Select Delay priority and Drop Precedence Expedited Forwarding (EF) PHB: Select TOS value as EF Default: Select TOS value as 0...
Page 77
IAD Gateway User Manual Class Class Class Class DROP Precedence Low Drop Precedence (AF11) (AF21) (AF31) (AF41) 001010 01001 011010 100010 Medium Drop Precedence (AF12) (AF22) (AF32) (AF42) 001100 01010 011100 100100 High Drop Precedence (AF13) (AF23) (AF33) (AF43) 001110 01011 011110 100110...
IAD Gateway User Manual 4.3.10 Password Configuration Screen Click [Password configuration] in the navigation panel to open the [Password Configuration] screen. It is highly recommended that you change the default password ([Null]). Change: First select login name as root or administrator, then enter current password, new password and confirm new password again to set new password.
IAD Gateway User Manual 4.3.11 ROM Configuration Screen Click [ROM Upgrade] in the navigation panel and open the [ROM Configuration] Screen. FTP/TFTP Server IP Address: Set TFTP server IP address Target File name: Set file name prepared to upgrade Method: Select download method as TFTP or FTP FTP Login: Set FTP login name and password...
IAD Gateway User Manual 4.3.12 Flash Clean Screen Click [Flash Clean] in the navigation panel and open the [Flash Clean] Screen. - Press CLEAN will clean all configurations of IAD and reset to factory default value. Note: User must re-configure all commands all over again (except Network Configure) once execute this function, - 74 -...
IAD Gateway User Manual 4.3.13 Commit Configuration Data Screen Click [Commit Data] in the navigation panel and open the [Commit Configuration Data] Screen. - Commit Date to save all configurations. Please remember to commit data before reboot your IAD. - 75 -...
IAD Gateway User Manual 4.3.14 Reboot IAD System screen Click [Reboot System] in the navigation panel and open the [Reboot IAD Gateway] Screen. Press reboot will reset IAD. Note: To execute reboot, please remember to do Commit Data before Reboot System.
IAD Gateway User Manual Part V: Telnet Command Interface This part gives information on how to configure IAD gateway via Telnet command line interface. - 77 -...
IAD Gateway User Manual 5.1 Login For you first login, enter the login: [root] and default no password. login: root password: Welcome to Terminal Configuration Mode Please enter your configuration item usr/config$ Note: Login account [root] or [administrator] is the default login account and there is no password needed.
Page 85
IAD Gateway User Manual usr/config$ passwd -set root voip Setting Login: root Password: voip usr/config$ - 79 -...
IAD Gateway User Manual 5.3 System Commands Overview 5.3.1 [help] Press help/man/ ? will display all command list of IAD. The following table lists all of the commands that you can use with the Gateway. Refer to the following chapters for descriptions of commonly used commands. This user’s guide...
IAD Gateway User Manual Command DESCRIPTION flash Clean all configuration from flash rom. sysconf System information manipulation. Configure SIP related parameters. security This command used configure account information included username and password obtained from the service provider. voice Voice information manipulation. support Special functions support manipulation.
IAD Gateway User Manual usr/config$ quit Disconnecting.. login: root Welcome to Terminal Configuration Mode Please enter your configuration item usr/config$ Note: It is recommended that type the [quit] command before you leave the console. If so, Gateway will ask password again when next user connects to console port.
Page 89
IAD Gateway User Manual usr/config$ debug Debug message information and configuration Usage: debug [-add type1 [[type2]...]] | -open | -close | -status -status Display the enabled debug flags. -add Add debug flag. -delete Remove specified debug flag. -open Start to show debug messages. -close Stop showing debug messages.
IAD Gateway User Manual usr/config$ debug -status Current debug type enabled : Debug Mode is open DEBUG-> SIP MSG usr/config$ 5.3.4 [reboot] After [commit], type [reboot] to reload Gateway in new configuration. The procedure is as below: usr/config$ reboot Start to Unregister ... Unregister complete...
IAD Gateway User Manual usr/config$ commit This may take a few seconds, please wait.. Commit to flash memory ok! usr/config$ Note: Users shall use [commit] to save modified value, or they will not be activated after system reboot. 5.3.6 [ifaddr] Configure and display Gateway network information.
Page 92
IAD Gateway User Manual usr/config$ ifaddr LAN information and configuration Usage: ifaddr [-print]|[-dhcp used]|[-sntp mode [server]] ifaddr [-ip ipaddress] [-mask subnetmask] [-gate defaultgateway] ifaddr [-dns index [dns server address]] [-ipsharing used[ip address]] ifaddr [-upnp used] -print Display LAN information and configuration. Specify WAN ip address.
Page 93
IAD Gateway User Manual Parameter Usages: -print: Print current IP setting and status -ip: Assigned IP address for Gateway -lanip: Specify LAN port IP address (For NAT function), use this command setup LAN IP address assigned to PC or other machine. usr/config$ ifaddr -lanip 192.168.XXX.YYY (The range of LAN IP is XXX: 1-254, YYY: 1-254) -mask: Assigned internet subnet mask...
Page 94
IAD Gateway User Manual Note: If the public IP address is not a fixed one, IAD cannot work behind NAT with peer-to-peer mode. -server: set EMS server IP. EMS is software to help user can easily configure products. Please contact with your reseller for more information.
IAD Gateway User Manual 5.3.7 [time] When SNTP function of Gateway is enabled and SNTP server can be found as well, type [time] command to show current network time. usr/config$ time Current time is WED SEP 17 12:36:49 2003 usr/config$ 5.3.8 [ping] Use [ping] to test whether a specific IP is reachable or not.
Page 97
IAD Gateway User Manual Parameter Usages: -print: Print out current contents of Phone Book. Users can also add index number, from 1 to 100, to the parameter to show specific phone number. Note: Index number: means the sequence number in phone book. If users do request a specific index number in phone book, Gateway will give each record a automatic sequence number as index.
IAD Gateway User Manual The e164 number defined in phone book will fully carry to destination. It is not just a representative number for destination’s IP Address. In other words, user dial this e164 number to reach destination, destination will receive the number and find out if it is matched to its e164, including Line number in some particular device.
IAD Gateway User Manual Parameter Usages: -print: print PPPoE status. -dev: Enable PPPoE Dial-up function -open: Open the connection -close: Close the connection -id: Input the User name ID provided by ISP -pwd: Input the User name password provided by ISP -reboot: Reboot the PPPoE connection.
Page 100
IAD Gateway User Manual usr/config$ flash Flash memory information and configuration Usage: flash [-clean] flash -clean Clean the configuration stored. Note: This command will clean the configuration stored in the flash and reboot it. usr/config$ Parameter Usages: -clean: clean all the user defined value, and reboot Gateway in factory default mode.
IAD Gateway User Manual usr/config$ flash -clean Flash clean start Flash clean success!! !! rebooting ... Attached TCP/IP interface to cpm unit 0 Attaching interface lo0...done HTTPD initialized... Flash Check WorkMode : PROXY_MODE Start registering to Proxy server AC4804[0] is ok AC4804[1] is ok successful 2 2 Initialize OSS libraries...OK!
Page 102
IAD Gateway User Manual usr/config$ sysconf System information and configuration Usage: sysconf [-print] [-idtime digit] [-bf digit] [-keypad dtmf] [-faxtype type][-2833type type][-lcdrop ON/OFF] [-droptime digit][-eod digit] [-callerid type] [-service used][-dtmfstart digits] [-dtmfend digits] sysconf -print -print Display system overall information and configuration. -idtime Inter-Digits time.(1~10 sec) -service...
Page 103
IAD Gateway User Manual Parameter Usages: -print: Print current sysconf settings. -idtime: Set the duration (in second) of two pressed digits in dial mode as timed out. If after the duration user hasn’t pressed next number, it will dial out all number pressed (1-10 seconds). -service: set SIP Phone to be normal mode or under hotline mode.
IAD Gateway User Manual usr/config$ sysconf -print System information Gateway Service Inter-Digits time BusyForward : OFF Keypad DTMF type : In-band End of Dial Digit Caller ID Type DTMF Caller ID Start Symbol : D DTMF Caller ID End Symbol RFC2833 Payload Type : 96 FAX Payload Type...
Page 105
IAD Gateway User Manual usr/config$ sip SIP stack information and configuration Usage: sip [-print] [-mode pxmode] [-outpx IPaddmress] sip [-px address] [-px2 address] [-domain domain] [-prefix prefixstring] [-line1 number] [-line2 number] [-line3 number] [-line4 number] [-expire t1] [-port udpPort] [-rtp rtpPort] sip -print -print Display SIP stack information and configuration.
Page 106
IAD Gateway User Manual -px: to specify Proxy address when IAD Gateway is in proxy mode. Proxy address can be IPv4 address or DNS name. -px2: to setting Secondary Proxy server address. Proxy address can be IPv4 address or DNS name. -Proxy port: Set Proxy port for IAD to send message, default value is 5060, if there is no special request of Proxy server, please don’t change this value.
IAD Gateway User Manual usr/config$ sip –print Run Mode : PEER-2-PEER MODE Prefix string : null Line1 : 1001 pbook search : OFF SIP listen port : 5060 RTP receive port : 16384 usr/config$ usr/config$ sip –print Run Mode : PROXY MODE Primary Proxy address : 10.1.1.2 Secondary Proxy address : null...
Page 108
IAD Gateway User Manual usr/config$ security Secuirty information and configuration Usage: security [-line number][-name username] [-pwd password] security [-print] -print Display system account information and configuration. -line Specify which line number you want to set the account. -name Specify user name. -pwd Specify password.
IAD Gateway User Manual 5.3.15 [voice] The voice command is associated with the audio setting information. There are four voice codecs supported by Gateway. - 103 -...
Page 111
IAD Gateway User Manual Parameter Usages: -print: Print current voice information and configurations. -send: To define packet size for each codec. 20/40/60/80 ms mean to send a voice packet per 20/40/60/80 milliseconds. The smaller the packet size, the shorter the delay time. If network is in good condition, smaller sending packet size is recommended.
IAD Gateway User Manual Note: Be sure to know well the application before you change voice parameters because this might cause incompatibility. For example: usr/config$ voice -print Voice codec setting relate information Sending packet size : G.729A : 40 ms G.723.1 : 60 ms G.711U...
Page 113
IAD Gateway User Manual users. usr/config$ support Special Voice function support manipulation Usage: support [-t38 enable] [-busy number] [-noanswer number] [-uncon number] support -print -t38 T.38(FAX) enabled/disabled. -busy Busy Forward number.(if empty, please fill "null") -noanswer No Anser Forward number.(if empty, please fill "null") -uncon Unconditional Forward number.(if empty, please fill "null")
IAD Gateway User Manual Note: It is not recommended to change the value in this command, only if users do know well the application. This might cause incompatibility with other devices. For example: usr/config$ support -print Special Voice function support manipulation T.38(FAX) support : Disabled Forward Numbers Busy Forward number: 0123456789...
Page 115
IAD Gateway User Manual usr/config$ tos IP Packet ToS(type of Service)/Differentiated Service configuration Usage: tos [-rtptype dscp] tos [-sigtype dscp] tos -print [-rtpreliab mode] tos -print Example: tos -rtptype 7 -sigtype 0 usr/config$ Parameter Usages: -rtptype: the packages of voice (0~63). -sigtype: the package of call signal (0~63).
IAD Gateway User Manual usr/config$ tos –print IP Packet ToS information: Signalling Packet: DSCP Code : 0 Media Packet DSCP Code : 0 usr/config$ 5.3.18 [phone] Gateway progress tone is configurable. Default tone value is set according to U.S. tone specification. Users may adjust the values according to their own country’s tone specification or users-defined tone specification.
Page 117
IAD Gateway User Manual usr/config$ phone Phone ringing , ringback tone , busy tone , dial tone setting and notes Usage: phone [-ring [freq ] [ringON ] [ringOFF ] [ringLevel]] [-rbt [freqHi ] [freqLo ] [freqHiLev] [freqLoLev] [Tone1ON] [Tone1OFF] [Tone2ON ] [Tone2OFF ]] [-bt [freqHi ] [freqLo ] [freqHiLev] [freqLoLev] [Tone1ON] [Tone1OFF] [Tone2ON ] [Tone2OFF ]]...
Page 118
IAD Gateway User Manual Parameter Usages: -print: Print current call progress tone configurations (ring: ring tone, rbt: ring back tone, bt: busy tone, dt: dial tone). This parameter should be accompanied with tone type. -ring: To set RING tone value. The played tone type, when Gateway is receiving a call.
Page 119
IAD Gateway User Manual usr/config$ phone -print rbt Phone ringback tone paramter Ringback Tone frequency high : 480 Ringback Tone frequency low : 440 Ringback Tone frequency high level : 155 Ringback Tone frequency low level : 155 Ringback Tone tone1 on : 2000 Ringback Tone tone1 off : 4000...
Page 120
IAD Gateway User Manual usr/config$ phone -print bt Phone busy tone paramter Busy Tone frequency high : 620 Busy Tone frequency low : 480 Busy Tone frequency high level : 155 Busy Tone frequency low level : 155 Busy Tone tone1 on : 500 Busy Tone tone1 off : 500...
IAD Gateway User Manual usr/config$ phone -print flash Phone flash paramter Flash frequency high : 800 Flash frequency low : 400 usr/config$ 5.3.19 [bureau] To set Hotline function must be under Peer-to-Peer mode and switch to hotline mode. usr/config$ bureau Bureau line setting information and configuration Usage: bureau [-hotline [Port DestIP TELnum]]...
IAD Gateway User Manual Port or Number]. For example 1. Destination is a FXS device, 628 is its Line1 number usr/config$ bureau -hotline 1 200.168.4.69 628 User picks up the Line1, and then hears the ringback tone generated from destination. Of course, 628 are ringing simultaneously. For example: usr/config$ bureau -print Bureau line setting relate information...
Page 123
IAD Gateway User Manual usr/config$ rom ROM files updating commands Usage: rom [-print] [-app] [-boot] [-dsptest] [-dspcore] [-dspapp] [-ht] [-method used] [-boot2m] -s TFTP/FTP server ip -f filename rom -print -print show versions of rom files. (optional) -app update main application code(optional) -boot update main boot code(optional) -boot2m...
IAD Gateway User Manual Note: Most of all, the Rom file needed to get upgrade is App or Boot2m. Please check the exactly Rom file before doing download procedure. -s: To specify TFTP server’s IP address when upgrading ROM files. -f: To specify the target file name, which will replace the old one.
Page 125
IAD Gateway User Manual usr/config$ passwd Password setting information and configuration Usage: passwd [-set [Login name] [Password]][-clean] passwd -set Loginname Password. -clean Clear all password stored in flash. Note: 1. Loginname can be only 'root' or 'administrator' 2. passwd -clean will clear all passwd stored in flash, please use it with care.
IAD Gateway User Manual usr/config$ passwd -set root root1234 Setting login: root Password: root1234 usr/config$ sr/config$ passwd -clean Please wait a moment!! Clean password OK. usr/config$ 5.3.22 [prefix] This command is for make rules for drop or insert prefix digits. - 120 -...
Page 127
IAD Gateway User Manual usr/config$ prefix Prefix drop/insert information and configuration Usage: prefix -add [prefix number][drop number][insert digits] prefix -delete index prefix -modify index [prefix number][drop number][insert number] prefix -print Prefix drop/insert information. prefix The prefix of dialed number. drop Drop prefix(Enable:1/Disable:0).
Page 128
IAD Gateway User Manual For example: usr/config$ prefix -print Prefix drop/insert information and configuration Index Prefix Drop Insert ========================================== ============== Enable 2000 usr/config$ - 122 -...