1. Manuals
  2. Brands
  3. Dynamix Manuals
  4. Gateway
  5. DW IAD - 162
  6. User manual

Dynamix DW IAD - 162 User Manual

Voip gateway (h.323)
Hide thumbs Also See for DW IAD - 162:
Table of Contents

Advertisement

Quick Links

Download this manual
D
y
n
a
m
i
x
D
W
I
A
D
-
1
6
2
D
y
n
a
m
i
x
D
W
I
A
D
-
1
6
2
V
o
I
P
G
a
t
e
w
a
y
(
H
.
3
2
3
)
V
o
I
P
G
a
t
e
w
a
y
(
H
.
3
2
3
)
User Manual

Advertisement

Table of Contents
loading

Related Manuals for Dynamix DW IAD - 162

Summary of Contents for Dynamix DW IAD - 162

  • Page 1 User Manual...

  • Page 2: Table Of Contents

    PREFACE----------------------------------------------------------------------------------------------------V PART I: DYNAMIX IAD-162 GATEWAY OVERVIEW ------------------------------------------- 1 1.1 Overview ----------------------------------------------------------------------------------------------- 2 1.2 Software Specifications --------------------------------------------------------------------------- 3 1.3 Hardware Specifications -------------------------------------------------------------------------- 4 PART II: START-UP --------------------------------------------------------------------------------------- 7 2.1 Software Installation Guide ---------------------------------------------------------------------- 8 2.1.1 Default Settings of Dynamix IAD-162 Gateway---------------------------------------------- 8 2.1.2 Additional Installation Requirements ------------------------------------------------------------ 8...
  • Page 3 3.1.1.1 One IAD gateway behind IAD ---------------------------------------------------------27 3.2 NAT mode (PPPoE) --------------------------------------------------------------------------------30 3.3 Upgrade Your IAD ----------------------------------------------------------------------------------32 3.3.1 Upgrade via Web management interface -------------------------------------------------------32 3.3.1.1 Before start ---------------------------------------------------------------------------------32 3.3.1.2 Upgrade Version --------------------------------------------------------------------------32 3.3.2 Upgrade via Telnet Command interface --------------------------------------------------------34 3.4 IAD 162 PSTN Line Application ----------------------------------------------------------------36 3.4.1 PSTN Outgoing Call ------------------------------------------------------------------------------36 3.4.1.1 Make PSTN call from TEL Phone set ------------------------------------------------36 3.4.1.2 PSTN Backup ------------------------------------------------------------------------------36...
  • Page 4 4.3.13 Password Configuration Screen----------------------------------------------------------------61 4.3.14 Version and Information Screen ---------------------------------------------------------------62 4.3.15 ROM Configuration Screen --------------------------------------------------------------------63 4.3.16 Flash Clean Screen ------------------------------------------------------------------------------64 4.3.17 Commit Configuration Data Screen -----------------------------------------------------------65 4.3.18 Reboot IAD System screen ---------------------------------------------------------------------66 PART V: TELNET COMMAND INTERFACE ----------------------------------------------------- 67 5.1 Login----------------------------------------------------------------------------------------------------68 5.2 Save and Reboot -----------------------------------------------------------------------------------68 5.3 System Commands Overview ------------------------------------------------------------------69 5.3.1 [help] ------------------------------------------------------------------------------------------------69...

  • Page 5: Preface

    Preface About this User’s Manual This user’s guide includes specifications, installation guide, web management and command line configuration interface for the Dynamix IAD -162 VoIP Gateway .

  • Page 6: Part I: Dynamix Iad-162 Gateway Overview

    Dynamix IAD-162 Gateway Part I: Dynamix IAD-162 Gateway Overview This part introduces the software/hardware specifications and default settings of the IAD Gateway. - 1 -...

  • Page 7: Overview

    Dynamix IAD-162 Gateway 1.1 Overview Dynamix IAD-161 is a one-port telephone extension and three ports SOHO Router to IP network gateway. It provides Data transfer by 10/100Mbps, telephone services and T.38 fax over IP network with easily operation and configuration. It is most suitable for SOHO and small-to-medium enterprise in Internet communication environment.

  • Page 8: Software Specifications

    Dynamix IAD-162 Gateway User Manual 1.2 Software Specifications Dynamix IAD-162 Gateway Features Provide Voice over IP and Fax over IP features. Built-in NAT/IP sharing function FSK and DTMF Caller ID Transmit Voice and T.38 fax simultaneously Support T.38 ECM function (Error Correction in high speed fax Mode) Provides call progress tone E.164 Common Dial Plan...

  • Page 9: Hardware Specifications

    Dynamix IAD-162 Gateway User Manual Remote Firmware Upgrade You can use FTP/TFTP to perform firmware upgrade for the Dynamix IAD-162 Gateway from a remote location. Security Password protection for system management Built-in NAT function. Certification CE, FCC 1.3 Hardware Specifications Chassis 190mm(W) x 110mm(D) x 51.5mm(H)
  • Page 10 Dynamix IAD-162 Gateway Power (Green): Light on: IAD is connected with power adapter correctly and power on. Light off: IAD is not connected with power adapter correctly or not power Status (Green): Light on: IAD is under Gatekeeper mode and successfully register to Gatekeeper.
  • Page 11 Dynamix IAD-162 Gateway Reset Button: All of the configuration, including network interface configuration, can be back to default value by pressing Reset Button. Ethernet Port: Ethernet port is for connecting VoIP Gateway to network, transmit rate supports 10/100 Base-T. Ethernet connector（LAN/WAN）...

  • Page 12: Part Ii: Start-Up

    Dynamix IAD-162 Gateway Part II: Start-UP This part explains how to configure essential and basic items before user can run Dynamix IAD-162 Gateway - 7 -...

  • Page 13: Software Installation Guide

    2.1.2 Additional Installation Requirements In addition to the contents of your package, there are other hardware and software requirements you need before you can install and use your Dynamix IAD- 162 Gateway. These requirements include: 1. A computer with an Ethernet NIC (Network Interface Card) installed.

  • Page 14: Save Data And Reboot

    Step 6.Connect other PC with LAN Ports (Optional) If you have more than one PC, you can connect them with LAN Ports (black) on the Dynamix IAD-162 Gateway. Please set these PCs as DHCP mode so that they can automatically get IP from IAD DHCP server.
  • Page 15 Data screen, click the [Commit] button. In the Commit Configuration Data screen will Display [Commit to Flash OK!], when IAD finished committing data. Step 2. Click [Reboot System] on the navigation panel. In the Dynamix IAD-162 Gateway screen, click the [Reboot] button. It will take around 40 seconds to reboot.
  • Page 16 Dynamix IAD-162 Gateway Step 3. Close the current browser windows and launch your web browser again. - 11 -...

  • Page 17: Setup Network

    Dynamix IAD-162 Gateway 2.1.3.2 Setup Network (1) Fixed IP To configure the VoIP Gateway IP address, please click [Network Interface] on the navigation panel. In the Network Interface screen, type a new IP address, subnet mask and the default routing gateway (e.g. IP Address: 192.168.13.62, Subnet mask: 255.255.248.0, Default routing gateway: 192.168.8.254) and click the OK...
  • Page 18 Dynamix IAD-162 Gateway (2) DHCP Click [Network Interface] on the navigation panel. In the Network Interface screen, enable the DHCP function if you are using the cable modem or DHCP server and click the [OK] button. - 13 -...
  • Page 19 Dynamix IAD-162 Gateway (3) PPPoE Configuring the VoIP Gateway IP address for PPPoE Mode. Click [Network Interface] on the navigation panel. In the Network Interface screen, Select IP mode: PPPoE, and put the info of the PPPoE User Name, password, and Reboot After Remote Host Disconnection: Enable (e.g.
  • Page 20 Dynamix IAD-162 Gateway PPPoE User Name: Set PPPoE authentication User Name. PPPoE Password: Set PPPoE authentication password. Reboot After Remote Host Disconnection: Enable/Disable auto reboot after PPPoE disconnection. If user enables this function, after PPPoE being disconnected, IAD will automatically reboot to re-connect, and after rebooting, if IAD still can’t get contact with server, IAD will keep trying to connect.

  • Page 21: Application Mode-Gk/Peer-To-Peer Mode

    2.1.3.3.1 GK routed mode GK mode means that there will be an intermediate Gatekeeper between Dynamix IAD-162 Gateway and the remote entity. While operating at this mode, Dynamix IAD- 162 Gateway will first register to the Gatekeeper located at the ISP side.
  • Page 22 Dynamix IAD-162 Gateway To configure Peer-To-Peer Mode in Dynamix IAD-162 Gateway, follow the steps below: Step 1. Configure the Dynamix IAD-162 Gateway H323 Configuration. Click [H323 Configuration] on the navigation panel. In the H323 Configuration screen, select Peer-to-Peer Mode function, set Line1 number and click the [OK] button.

  • Page 23: Essential Configuration Via Telnet Command Line Interface

    Dynamix IAD-162 Gateway 2.1.4 Essential Configuration via Telnet Command Line interface This section describes how to setup IAD via Telnet command line interface. Please follow procedures below to configure essential items before you use Dynamix IAD-162 Gateway. 2.1.4.1 Save Data and Reboot After any configuration has been made, user has to save all data and reboot system to make configurations take effect.
  • Page 24 Dynamix IAD-162 Gateway usr/config$ commit usr/config$ reboot Step 4. When IAD successfully establish PPPoE connection, use command [ifaddr -print] to see detail information. For example: usr/config$ ifaddr -print IP mode : PPfPoE PPPoE adapter information Status : Ready IP address : 61.223.39.135...

  • Page 25: Application Mode-Gk/Peer-To-Peer Mode

    2.1.4.3.1 GK routed mode GK mode means that there will be an intermediate Gatekeeper between Dynamix IAD-162 Gateway and the remote entity. While operating at this mode, Dynamix IAD- 162 Gateway will first register to the Gatekeeper located at the ISP side.
  • Page 26 Dynamix IAD-162 Gateway Step 2. Configure Phone Book, using “pbook” command. usr/config$ pbook –add name TEST1 ip 10.1.1.1 e164 10 In this case user add one callee record named as TEST1, IP address as 10.1.1.1, and mapping e.164 number as 10. After phone book data has been set, user can dial 10 to make a call for IP 10.1.1.1.

  • Page 27: Essential Configuration Via Installation Wizard

    Dynamix IAD-162 Gateway 2.1.5 Essential Configuration via Installation Wizard Installation Wizard is a friendly software tool that can provide you an easy way to configure your VoIP devices. You only need to Input the MAC address of your product and Click [Search Device]; you can configure your VoIP device without changing your PC’s setting.

  • Page 28: Special Housing Installation Guide

    Dynamix IAD-162 Gateway 2.1 Special Housing Installation Guide adjustable Dynamix IAD 162 has special housing for vertical or horizontal type. Please follow procedures as below to change type you like. 2.1.1 Horizontal Type 2.1.1.1 Insert stand board on one side.

  • Page 29: Vertical Type

    Dynamix IAD-162 Gateway 2.1.2 Vertical Type 2.1.2.1 Insert stand board on one side. 2.1.2.2 Insert the other stand board on the same side. 2.1.2.3 Finally IAD can stand as vertical type. - 25 -...

  • Page 30: Part Iii: Special Applications And Features

    Dynamix IAD-162 Gateway Part III: Special Applications Features This part explains how to configure IAD Gateway under special application mode, such as behind NAT, and how to upgrade firmware. - 26 -...

  • Page 31: Behind Ip-Sharing

    Step 4. IAD Gateway must enable the IP Sharing function for the fixed / dynamic WAN IP Address. Note: With Dynamic WAN IP Address, a valid GK for Dynamix IAD-162 Gateway to get register on is necessary. In other words, it is not workable in Peer-to-Peer mode while dynamic WAN IP Address.
  • Page 32 Activate DMZ DMZ Host IP: 192.168.1.5 Step 6. Configure the Dynamix IAD-162 Gateway IP address for IP Sharing Mode. Click [Network Interface] on the navigation panel. In the Network Interface screen, enter the IP address, Subnet mask and the default gateway in the network table.
  • Page 33 Dynamix IAD-162 Gateway click the [Reboot] button. It will take around 40 seconds to reboot. Step 10. Close the current browser windows and launch your web browser again. Enter the new IP address in the Location or Address field. - 29 -...

  • Page 34: Nat Mode (Pppoe)

    Dynamix IAD-162 Gateway 3.2 NAT mode (PPPoE) Step 1. Set PPPoE mode, using [ifaddr –mode 2], input the user id & password provided by your ISP, using [ifaddr –id –pwd], reboot the device after disconnection, using [ifaddr –reboot 1] usr/config$ ifaddr –mode 2 usr/config$ ifaddr –id 123@hinet.net (PPPoE login account)
  • Page 35 Dynamix IAD-162 Gateway time zone : GMT+8 cycle=1024 mins IPSharing : no IPSharing device. IP change : Disable PPPoE user name : 84460791@hinet.net PPPoE password : ******** PPPoE reboot : Yes PPPoE echo : Enable EMS IP : 192.168.10.71 EMS user name...

  • Page 36: Upgrade Your Iad

    Step 2. Note down your current configurations, such as [H323 Configuration], [Phone Book]. 3.3.1.2 Upgrade Version Step 1. To update the Dynamix IAD-162 Gateway ROM Version, please click [ROM Upgrade] on the navigation panel. In the [ROM Configuration] screen, type TFTP/FTP Server IP address, Target File Name, Method, Target File Type (e.g.
  • Page 37 Dynamix IAD-162 Gateway Step 3. Click [Flash Clean] on the navigation panel. In the Flash Clean screen, click the [CLEAN] button. Step 4. In the Flash Clean screen to Display [Flash cleaned!! Please reboot your system!!], when Flash Clean Ok.

  • Page 38: Upgrade Via Telnet Command Interface

    Dynamix IAD-162 Gateway Step 5. Click [Reboot System] on the navigation panel. In the Reboot Dynamix IAD-162 Gateway screen, click the [Reboot] button. It will take 40 seconds to reboot. Step 6. Close the current browser windows and launch your web browser again.
  • Page 39 Dynamix IAD-162 Gateway -app, boot, boot2m, dsptest, dspcore, dspapp, ht: To update main Application program code, Boot code, DSP testing code, DSP kernel code, or DSP application code, and Hold Tone file. Note: Most of all, the Rom file needed to get upgrade is App or Boot2m. Please check the exact Rom file before doing download procedure.

  • Page 40: Iad 162 Pstn Line Application

    IP call, TEL phone set will ring, and user can pick up the call from PSTN side. The Dynamix IAD-162 Gateway has “call waiting tone” function, when IP side is under calling, if PSTN side has an incoming call, the user in IP side will hear a call waiting tone.

  • Page 41: Reset Button Feature

    Dynamix IAD-162 Gateway 3.5 Reset Button Feature Dynamix IAD-162 has a reset button, it is using software reset. User just need to press this button 3 seconds, all of the configuration, including network interface configuration, will be back to default value.

  • Page 42: Part Iv: Web Management Interface

    Dynamix IAD-162 Gateway Part IV: Web Management Interface This part explains how to configure theDynamix IAD-162 Gateway via WEB t i t f - 38 -...

  • Page 43: Login And Welcome Screen

    Dynamix IAD-162 Gateway 4.1 Login and welcome screen Step 1. Start your web browser. Step 2. Launch your web browser and enter [192.168.123.123] (the default IP address of the LAN port) in the Location or Address field. Press Enter. Step 3. Password request screen will appear as below. Please input “root” or “administrator”...

  • Page 44: Save And Reboot

    Dynamix IAD-162 Gateway l 4.2 Save and Reboot Click OK at the end of every configuration page to confirm your changes. All configurations will not take effect before reboot system. Please remember to do [Commit Data] to save all configuration then [Reboot System] to reboot IAD.

  • Page 45: Web Management Configuration

    Dynamix IAD-162 Gateway 4.3 Web Management Configuration 4.3.1 Network Interface Click [Network Interface] in the navigation panel and open the Network Interface Screen. IP Mode: To configure the fixed or dynamic IP address for this unit. Please configure to PPPoE if the ADSL is using the PPPoE type.
  • Page 46 Dynamix IAD-162 Gateway IP Address: Set WAN IP Address of IAD. Subnet Mask: Set the Subnet Mask of IAD Default routing gateway: Set Default routing gateway of IAD DHCP server: The DHCP server IP address. DHCP Server switch: Enable the DHCP function for the LAN interface.
  • Page 47 Dynamix IAD-162 Gateway Send PPPoE Echo Request: In the PPPoE mode, if the network connector or the ADSL modem was lost, after the connector and modem connected, it will reboot automatically for the re-connect with the PPPoE server. IP: Set the EMS server IP address.

  • Page 48: H323 Configuration Screen

    Dynamix IAD-162 Gateway 4.3.2 H323 Configuration Screen Click [H323 Configuration] in the navigation panel and open the H323 Configuration Screen. Mode: Choosing the calling mode for this gateway. GK routed: Users have to register on the GK if users picked up this option.
  • Page 49 Dynamix IAD-162 Gateway Peer-to-Peer: It only supports the peer-to-peer and users have to define the phone book for this mode. Gatekeeper IP Address: Enter the GK ip if users pick up the GK routed mode. It support on GK mode only.
  • Page 50 Dynamix IAD-162 Gateway Note: When users enable this function, the GK name is necessary. User could enable this function first and define the name of the GK. Gateway will send the GRQ message by broadcast if users define the IP address of GK is 255.255.255.255. If the gateway receive GCF message that’s meaning the GK accept the request...

  • Page 51: Line Configuration

    Dynamix IAD-162 Gateway 4.3.3 Line Configuration Click [System Configuration] in the navigation panel and open the [System Configuration] Screen. The Line configuration will show the status of the registrations and the ports. It includes the hunt group, hotline, and no answer forward configuration.

  • Page 52: Phone Book Configuration Screen

    Dynamix IAD-162 Gateway 4.3.4 Phone Book Configuration Screen Click [PPPoE Configuration] in the navigation panel and open the [PPPoE Configuration] Screen. The Phone Book configuration is only support the gateway in Peer-to-Peer mode. Add Data: User can specify 5 sets of phone book via Web Management Interface.

  • Page 53: Support Configuration Screen

    Dynamix IAD-162 Gateway 4.3.5 Support Configuration Screen Click [Support Configuration] in the navigation panel and open the [Support Configuration] Screen. This gateway supports the FAX over IP, fast start function and other functions. T.38 FAX: Enable this function to support the FAX function.

  • Page 54: System Configuration Screen

    Dynamix IAD-162 Gateway 4.3.6 System Configuration Screen Click [System Configuration] in the navigation panel and open the [System Configuration] Screen. Inter Digit Time: The call will be sent out if user didn’t enter the digits after this timer. Forward time: It supports the No Answer Forward function. If users configure it...
  • Page 55 Dynamix IAD-162 Gateway for 10, the call will be forwarded when it rings about 10 seconds. From 5 to 65535. Keypad Type: User could define the keypad for the DTMF sending. In-Band : The DTMF signal sending by RTP. Out-Band : The DTMF signal sending not by RTP. Including the H.245(Alpha), H.245(Signal), Q.931 and RFC 2833.
  • Page 56 Dynamix IAD-162 Gateway from the IP to PSTN side. It could only support the one-stage-dialing function. Only support FXO. Auto connect time (FXO): The FXO will send the connect message to the IP side is this timer is up in the one-stage-dialing function. It could only support the one-stage-dialing function.

  • Page 57: Voice Configuration Screen

    Dynamix IAD-162 Gateway 4.3.7 Voice Configuration Screen Click [Voice configuration] in the navigation panel and open the [Support Configuration] Screen. Codec Priority: Set priority preference of installed codes, G.723, G.711A, G.711U, G.729, G.729A, G.729B, and G.729AB. Frame Size: Set Specify sending packet size, G.723: 30/60/90, G.711A, G.711U, G.729, G.729A, G.729B, G.729AB: 20/40/60ms.The smaller the...

  • Page 58: Phone Configuration Screen

    Dynamix IAD-162 Gateway 4.3.8 Phone Configuration Screen Click [Phone Configuration] in the navigation panel and open the [Phone Configuration] Screen. For tone simulation, IAD Gateway adopts dual frequencies as traditional telephone does. If users want to have their own call progress tone, they can change the value of tones.
  • Page 59 Dynamix IAD-162 Gateway ringing ring ON/OFF: 0 ~ 8000 (Unit: ms) ringing level: 0 ~ 94 (Unit: V) tone frequency: 0 ~ 65535 (Unit: Hz) tone freqLevel: 0 ~ 65535 (Unit: mVrms) tone Tone ON/OFF: 0 ~ 8000 (Unit: ms)

  • Page 60: Rtp Pay Load Type Configuration

    Dynamix IAD-162 Gateway 4.3.9 RTP Pay Load Type Configuration Click [RTP Payload Type Configuration] in the navigation panel and open the [RTP Payload Type Configuration] Screen. RFC2833 Payload Type: To define the payload type for RFC2833 type. DTMF Payload Type: To define the payload for the DTMF type.

  • Page 61: Ip Packets Tos Configuration Screen

    Dynamix IAD-162 Gateway 4.3.10 IP Packets ToS Configuration Screen The Type of Service should be worked with the network router. The router will check all the packets if it support the TOS function. There is a field in the packet for the TOS value.
  • Page 62 Dynamix IAD-162 Gateway DROP Precedence Class #1 Class #2 Class #3 Class #4 Low Drop Precedence (AF11) (AF21) (AF31) (AF41) 001010 010010 011010 100010 Medium Drop Precedence (AF12) (AF22) (AF32) (AF42) 001100 010100 011100 100100 (AF13) (AF23) (AF33) (AF43) High Drop Precedence...

  • Page 63: Ddns Screen

    Dynamix IAD-162 Gateway 4.3.11 DDNS Screen IAD supports DDNS function. Before using this function, please have a DDNS account and some info from your DDNS server. Click [Password configuration] in the navigation panel to open the [Password Configuration] screen. Status: To enable or disable this function.

  • Page 64: Prefix Configuration Screen

    Dynamix IAD-162 Gateway 4.3.12 Prefix Configuration Screen The Prefix function is using the drop and inserts function. Click [Prefix Configuration] in the navigation panel and open the [Prefix Configuration] Screen. Index: Setting the index number for prefix record (max 30 record).

  • Page 65: Password Configuration Screen

    Dynamix IAD-162 Gateway 4.3.13 Password Configuration Screen There are two login accounts in this unit. One is the “root” another is “administrator”. The default passwords for these two accounts are null. Users can define the passwords for these two accounts.

  • Page 66: Version And Information Screen

    Dynamix IAD-162 Gateway 4.3.14 Version and Information Screen Users can get more detail about the software version for all the parts in this web page. Click [Version and Information] in the navigation panel and open the [Version and Information] Screen.

  • Page 67: Rom Configuration Screen

    Dynamix IAD-162 Gateway 4.3.15 ROM Configuration Screen Click [ROM Upgrade] in the navigation panel and open the [ROM Configuration] Screen. FTP/TFTP Server IP Address: Set TFTP server IP address Target File name: Set file name prepared to upgrade Method: Select download method as TFTP or FTP...

  • Page 68: Flash Clean Screen

    Dynamix IAD-162 Gateway 4.3.16 Flash Clean Screen Click [Flash Clean] in the navigation panel and open the [Flash Clean] Screen. Press CLEAN will clean all configurations of IAD and reset to factory default value. Note: User must re-configure all commands all over again (except Network Configure) once execute this function.

  • Page 69: Commit Configuration Data Screen

    Dynamix IAD-162 Gateway 4.3.17 Commit Configuration Data Screen Click [Commit Data] in the navigation panel and open the [Commit Configuration Data] Screen. Commit Date to save all configurations. Please remember to commit data before reboot your IAD. - 65 -...

  • Page 70: Reboot Iad System Screen

    Dynamix IAD-162 Gateway 4.3.18 Reboot IAD System screen Click [Reboot System] in the navigation panel and open the [Reboot Dynamix IAD- 162 Gateway] Screen. Press reboot will reset IAD. Note: To execute reboot, please remember to do Commit Data before Reboot System.

  • Page 71: Part V: Telnet Command Interface

    Dynamix IAD-162 Gateway Part V: Telnet Command Interface This part gives information on how to configure Dynamix IAD-162 gateway via Telnet command line interface. - 67 -...

  • Page 72: Login

    Dynamix IAD-162 Gateway 5.1 Login For you first login, enter the login: [root] and default no password. login: root password: Welcome to Terminal Configuration Mode Please enter your configuration item usr/config$ Note: Login account [root] or [administrator] is the default login account and there is no password needed.

  • Page 73: System Commands Overview

    This user’s guide describes commands that are helpful for configuring the Gateway. Using commands not documented in the user’s guide can damage the unit and possibly render it unusable. Commands with Dynamix IAD-162 Gateway Command Description help...

  • Page 74: Quit]

    Dynamix IAD-162 Gateway 5.3.2 [quit] Type [quit] will quit the Gateway configuration mode. And turn back to login prompt. usr/config$ quit Disconnecting.. login: root Welcome to Terminal Configuration Mode Please enter your configuration item usr/config$ Note: It is recommended that type the [quit] command before you leave the console. If so, Gateway will ask password again when next user connects to console port.

  • Page 75: Reboot]

    Dynamix IAD-162 Gateway add: Add debug flag. h323: h323 related information vp: voice related information delete: Remove specified debug flag. open: Start to show debug messages. close: Stop showing debug messages. In this example, user open debug flags including h323, vp, h323vp.

  • Page 76: Flash]

    Dynamix IAD-162 Gateway login: 5.3.5 [flash] Clean the configuration stored in flash. usr/config$ flash Flash memory information and configuration Usage: flash [-clean] flash -clean Clean the configuration stored. Note: This command will clean the configuration stored in the flash and reboot it.

  • Page 77: Commit]

    Dynamix IAD-162 Gateway Flash clean ok!! Rebooting ... Attached TCP/IP interface to cpm unit 0 Attaching interface lo0...done Hardware Type : 1FXS Set RTL8305SB no answer from 192.168.4.114 HTTPD initialized... cmInitialize succeed! Ras port:1024 CallSignal port:1720 AC4804[0] is ok successful 1 2 Initialize OSS libraries...OK!
  • Page 78 Dynamix IAD-162 Gateway Usage: ifaddr [-print][-mode used][-ip IP Address][-mask Subnet Mask] [-gate Default Gateway][-dns 1 IP Address][-http portnumber] [-dhcpsv used][-nat used][-lanip IP Address][-sntp mode [server]] [-timezone GMT][-ipsharing used IP address][-ipchange used] [-id PPPoE username][-pwd PPPoE password][-reboot used][-emsip EMS IP] [-emsid EMS username][-emspwd EMS password][-emstime EMS digit] -print Display network information and configuration.
  • Page 79 Dynamix IAD-162 Gateway Range of IP address setting (0.0.0.0 ~ 255.255.255.255). LAN IP can not support subnet x.x.0.x Example: ifaddr -mode 0 ifaddr -ip 210.59.163.202 -mask 255.255.255.0 -gate 210.59.163.254 ifaddr -dns 1 168.92.1.1 -dns 2 168.95.1.2 ifaddr -http 80 ifaddr -lanip 192.168.123.123 ifaddr -sntp 1 210.59.163.254...

  • Page 80: Time]

    Dynamix IAD-162 Gateway ipsharing: To specify a global fixed IP address, user can add this IP address in the command. usr/config$ ifaddr -ipsharing 1 210.11.22.33 Note: If the IP address is not a fixed one, the dedicated IP address is not necessary in the command.

  • Page 81: Ping]

    Dynamix IAD-162 Gateway 5.3.9 [ping] Use [ping] to test whether a specific IP is reachable or not. For example: if 192.168.1.2 is not existing while 210.63.15.32 exists. Users will have the following results: usr/config$ ping 192.168.1.2 no answer from 192.168.1.2 usr/config$ ping192.168.1.254...
  • Page 82 Dynamix IAD-162 Gateway -codec Codec select method (0=Caller, 1=Master). -reverse Reverse.(0=Disable, 1=Enable). -callerid caller ID.(0=Disable, 1=Enable). -localrbt Local ring back tone (0=Disable, 1=Enable). -roundtrip Disconnect no connect in line busy.(0=Disable, 1=Enable). -gwprefix Drop gateway prefix when call from IP (0=Keep, 1=Drop).
  • Page 83 Dynamix IAD-162 Gateway numbers, he can dial a defined digit – [*] to disable the function [sysconf –prefixdisab *], then dial to the number he wants to dial. codec: Set who is the one to determine voice codec during negotiation. 0 is caller will determine the codec, and 1 is mater will determine the codec.

  • Page 84: H323]

    Dynamix IAD-162 Gateway Caller ID : Disable Local generate ring back tone : Enable Round Trip : Disable Gateway prefix : Keep End of dial : Enable Dial to PSTN side : Enable usr/config$ 5.3.11 [h323] This command is to configure H.323 related parameters.
  • Page 85 Dynamix IAD-162 Gateway -h225 H225 ras port (1~65535). -q931 H225 call signal port (1~65535). -dstq931 Destination H225 call signal port (1~65535). -range Dynamically allocated port range (1~65535). -respto Max waiting time for 1st response to a new call (1~200). -connto Max waiting time for call establishment after receiving 1st response of a new call (1~20000).
  • Page 86 Dynamix IAD-162 Gateway display: An addition name for user to recognize in called site. gkid: Set GateKeeper name for GateKeeper discovery. When Gateway send out GateKeeper discovery message will search GateKeeper with this GateKeeper name. gkdis: Set auto discovery function on or off. If this function is enabled and IP address of GateKeeper is set as 255.255.255.255, Gateway will multicast to...

  • Page 87: Line]

    Dynamix IAD-162 Gateway Gatekeeper discovery : Off Gatekeeper ID : GK RAS TTL time : 60 RTP port : 16384 Gatekeeper finding port : 1718 GK RAS port : 1719 H225 RAS port : 1024 H225 Call signal port : 1720...

  • Page 88: Prefix]

    Dynamix IAD-162 Gateway group number represent different hunt group. hotline: Set hotline table. The Hotline Mode is applied in limited two channels. User just picks up the phone set of one FXS TEL or calls in one FXO line, and gateway will automatically dial out a phone number. In the other hand, user will hear ring back tone or dial tone immediately depended on configurations of destination device.
  • Page 89 Dynamix IAD-162 Gateway -modify Modify prefix drop/insert information index : The prefix index number record. prefix : The prefix of dialed number. drop : Drop prefix (0=Disable, 1=Enable). insert : 1~10 digits. -delete Delete prefix index number record. Example: prefix -print...

  • Page 90: Pbook]

    Dynamix IAD-162 Gateway usr/config$ 5.3.14 [pbook] Phone Book function allows users to define their own numbers, which mapping to real IP address. It is effective only in peer-to-peer mode. When adding a record to Phone Book, users do not have to reboot the machine, and the record will be effective immediately.
  • Page 91 Dynamix IAD-162 Gateway pbook -add name test e164 1234 ip 192.168.1.10 pbook -add name test e164 1234 ip 192.168.1.10 port 1720 drop 1 insert 5678 pbook -modify 1 name test e164 5678 ip 192.168.1.10 port 1720 drop 0 pbook -delete 1...

  • Page 92: Voice]

    Dynamix IAD-162 Gateway is matched to its e164, including Line number in some particular device. For example: usr/config$ pbook –print Phone book information and configuration Index Name E.164 Port Drop Insert ======================================================== test 192.168.13.78 1720 Disable usr/config$ 5.3.15 [voice] The voice command is associated with the audio setting information. There are four voice codecs supported by Gateway.
  • Page 93 Dynamix IAD-162 Gateway G.729A G.729B G.729AB G.711U G.711A -volume Specify the following levels: voice volume (0~63, default: 30), input gain (0~63, default: 30), dtmf volume (0~31, default: 23), -nscng No sound compression and CNG (G.723.1 only, 0=Off, 1=On). -echo Setting of echo canceller. (0=Off, 1=On, per port basis).
  • Page 94 Dynamix IAD-162 Gateway input gain stands for volume, which the opposite party hears (range 0~38, default: 28). dtmf volume stands for DTMF volume/level, which sends to its own Line (range 0~31, default: 23). nscng: Silence suppression and comfort noise generation setting (1 = ON;...

  • Page 95: Support]

    Dynamix IAD-162 Gateway G.729B : There is no setting G.729AB : There is no setting G.711(U-Law) : There is no setting G.711(A-Law) : There is no setting Echo canceller : On Jitter buffer Min Delay : 90 Max Delay : 150 usr/config$ 5.3.16 [support]...
  • Page 96 Dynamix IAD-162 Gateway support -faxrdd support -fstart 1 support -tunnel 1 support -h245fs 1 support -earlyh245 1 support -h450 1 usr/config$ Parameter Usages: print: print current settings in support command. t38: Enable or disable T.38 fax ability. The function is will automatically defer codec (G.723 or G.729a) to T.38 when FAX signal is detected.

  • Page 97: Sysinfo]

    Dynamix IAD-162 Gateway For example: usr/config$ support -print Special Voice function support manipulation T.38(FAX) support : Disabled T.38(FAX) Request Mode : Enabled T.38(FAX) ECM : Disabled T.38(FAX) ASN.1 : Disabled FAX redundancy depth FastStart support : Disabled Tunneling support : Disabled H.245 message after FastStart support : Enabled...
  • Page 98 Dynamix IAD-162 Gateway specification or users-defined tone specification. usr/config$ phone Phone ringing , ringback tone , busy tone , dial tone setting and notes Usage: phone [-print [ring][rbt][bt][dt][flash]] [-ring [freq ][ringON ][ringOFF ][ringLevel]] [-rbt [freqLo ][freqHi ][freqLoLev][freqHiLev] [Tone1ON][Tone1OFF][Tone2ON ][Tone2OFF ]]...

  • Page 99: Tos]

    Dynamix IAD-162 Gateway phone -flash 100 300 usr/config$ Parameter Usages: print: Print current call progress tone configurations (ring: ring tone, rbt: ring back tone, bt: busy tone, dt: dial tone). This parameter should be accompanied with tone type. ring: To set RING tone value. The played tone type, when Gateway is receiving a call.

  • Page 100: Ddns]

    Dynamix IAD-162 Gateway IP Packet ToS (Type of Service)/Differentiated Service configuration Usage: tos [-print][-rtptype dscp][-sigtype dscp] tos -print Display IP packet Tos configuration. -rtptype The packages of voice (0~63). -sigtype The package of call signal (0~63). Example: tos -rtptype 7 -sigtype 0...
  • Page 101 Dynamix IAD-162 Gateway [-passwd Password][-checkip used][-checkipsrv Address][-delay time] [-force IP] ddns -print Display Dynamic DNS information and configuration. -enable Use the dynamic DNS service(0=Disable, 1=Enabled). -server Specify DDNS server address. -hostname Registered domain name. Registered account ID. -passwd Registered account password.

  • Page 102: Pt]

    Dynamix IAD-162 Gateway Support DDNS Server: www.dyndns.org. For example: usr/config$ ddns -print Dynamic DNS service information Status : Enable Server : www.dyndns.org Host Name : totoro609.dnsalias.net : totoro609 Password : 123456789 Check IP : Disable IP Check Server1 : checkip.dyndns.org IP Check Server2 : checkip.dyndns.org...

  • Page 103: Rom]

    Dynamix IAD-162 Gateway For example: usr/config$ pt -print RTP payload type information RFC2833 payload type : 96 DTMF payload type : 100 FAX payload type : 101 FAX ByPass payload type : 102 MODEM ByPass payload type : 103 Redundancy payload type...

  • Page 104: Auth]

    Dynamix IAD-162 Gateway This command can run select one option in 'app', 'boot', , 'dsptest', 'dspcore', and 'dspapp'. Example: rom -method 1 rom -ftp vwusr vwusr rom -app -s 192.168.4.101 -f app.bin usr/config Parameter Usages: print: show versions of all rom files.
  • Page 105 Dynamix IAD-162 Gateway usr/config$ auth Auth to customized the WEB configuration item for administrator. Usage: auth -print Display auth switch configuration. Use item name to do config name (0=Disable, 1=Enabled). Example: auth -ifaddr 1 usr/config$ Parameter Usages: “ item name ”: Assign the configurable item for “administrator”...

  • Page 106: Passwd]

    Dynamix IAD-162 Gateway usr/config$ 5.3.24 [passwd] For security concern, users have to input the password before entering configuration mode. [passwd] command is for password setting purpose. usr/config$ passwd Password setting information and configuration Usage: passwd [-set [Login name] [Password]][-clean] passwd -set Loginname Password.
  • Page 107 Dynamix IAD-162 Gateway usr/config$ sr/config$ passwd -clean Please wait a moment!! Clean password OK. usr/config$ - 103 -...

Table of Contents