FXS-08 Technical Manual EN-V2.0a 1. Introduction 1.1 FXS-08 --8-ports Telephony Gateway The FXS-08 is an 8-ports FXS VoIP gateway to connect 8 analog phones (POTS) and includes 1-WAN/4-LAN 10/100 base-T NAT router for diverse network environment. Field-proven quality of Voice communication and Fax transmission over IP broadband access network to makes FXS-08 to be an excellent solution for various VoIP applications.
FXS-08 Technical Manual EN-V2.0a Ring Back Tone Dial Tone Programming Tone Call Features Ø Call Hold Call Transfer (Blind & consultant) Call Forward (Unconditional / No Answer / Busy) Call Conference (3-ways) MWI – Message Waiting Indication Ø IP line hunting Ø...
FXS-08 Technical Manual EN-V2.0a OUTPUT: DC 12V, 3.0A Regulatory Compliance: FCC (Part 15, Class B) & CE 2. Appearance 2.1 Front Panel: LED Indicators Description Power When the power adapter is connected, the LED will light up green. Proxy When the gateway is registered successfully to a Proxy, this will light up green.
Page 8
FXS-08 Technical Manual EN-V2.0a data is transmitted through this port, it will flash green. The status LED for FXS port 1, this will light up amber orange when the connected phone ’ s handset is lifted, or when the connected phone is engaged in a conversation. It will flash amber orange when there is an incoming call.
FXS-08 Technical Manual EN-V2.0a 2.2 Rear Panel: Item Description Reset Press and hold over 5 seconds to reload factory default setting, this will erase all the settings configured on the gateway. The RJ-11 FXS port 8, connects analog phone sets, trunk line or PABX.
FXS-08 Technical Manual EN-V2.0a 3. Environment Setup and IP Connection Please make sure that the network interface of your computer is working fine and cross over line (RJ-45) is connected to the computer correctly. You can also connect your computer to the gateway using a hub. The FXS-08 by default uses DHCP for its LAN port and assigns IP addresses to clients connected to it, please make sure that your PC or Notebook’...
Page 11
FXS-08 Technical Manual EN-V2.0a 3. You will see a pop-up window requesting username and password before you can login to the web configuration menu. Username is “root” while password is blank “ “ (see figure below). 3. You will enter the main page of the web configuration interface after you keyed in the username and password correctly (see figure below).
FXS-08 Technical Manual EN-V2.0a 3.2 Network Configuration The following instructions will explain the configurations for setting up the WAN port of the FXS-08. There are in total three methods of connections: Static IP, DHCP and PPPoE. Note: You can retrieve the IP address of the WAN port by keying #126# on the phone set that is connected to the FXS port of the gateway.
Page 13
FXS-08 Technical Manual EN-V2.0a WAN Setting Item Description Static IP DHCP PPPoE Connected mode Select the connection method for the WAN port of the FXS-08, you can choose the following: Static IP DHCP PPPoE Current IP Address Show current IP address DNS server mode Select the DNS behavior, you can choose the following:...
Page 14
FXS-08 Technical Manual EN-V2.0a WAN Setting Item Description Static IP DHCP PPPoE Default gateway Specify the IP address of the default gateway. Remote access Restricts/Blocks users restriction connecting to the WAN port’ s IP remotely, you can Enable/Disable this option. PPPoE userID Specify the username of the PPPoE account...
FXS-08 Technical Manual EN-V2.0a 3.2.1.1 WAN Setting --Static IP 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes.
FXS-08 Technical Manual EN-V2.0a 3.2.1.2 WAN Setting --DHCP Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes. 3.2.1.3 WAN Setting --PPPoE 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2.
FXS-08 Technical Manual EN-V2.0a 3.2.2. LAN Setting LAN Setting ITEM Description LAN IP address Specify the IP address of the FXS-08’ s LAN port. LAN mask address Specify the mask address for FXS-08’ s LAN port. DHCP server Enable/Disable DHCP function on the LAN port.
Page 18
FXS-08 Technical Manual EN-V2.0a LAN Setting ITEM Description Domain Name You can specify the domain name that will be assigned by the DHCP server to the attached network devices. The DHCP server will send information on the “server host name” to the DHCP client.
FXS-08 Technical Manual EN-V2.0a 3.3 General configuration To make VoIP calls, you will need a SIP account provided by the SIP Proxy you are registered with. To configure the relevant SIP settings, please refer to the instructions explained below. 3.3.1 SIP Setting 3.3.1.1 Proxy mode Primary proxy/P2P IP Specify the data of primary proxy :...
Page 20
FXS-08 Technical Manual EN-V2.0a configuration Representative Number mode or L1~L8 Separate Number mode, or the Blending mode (Representative Number & L1~L8 Separate Number mode) Representative Number Input the relevant data for Enable line, Register status, SIP Account, Number, Password, and Display Name. Note: If you use the representative number to register, please check the max.
Page 21
FXS-08 Technical Manual EN-V2.0a If you Enable the Secondary proxy, system will display the “Secondary proxy call Number Configuration” figure as shown below. Secondary proxy Call Number If you enable the secondary proxy, configuration System will display “Secondary proxy Call Number configuration” figure, Please refer to the description of “Primary proxy Call Number configuration”...
FXS-08 Technical Manual EN-V2.0a 3.3.1.2 Peer to Peer mode Peer A— FXS-08(for example the IP address is : 192.168.15.14) Peer B— FXS-08(for example the IP address is: 192.168.15.62)
Page 23
FXS-08 Technical Manual EN-V2.0a Primary proxy/P2P IP Specify the destination IP Address of (Peer A/ Peer B) Peer to Peer mode, and specify the port# with 5076. In this application, we define the Peer to Peer mode in 2 groups. If you want to make call to others IP addresses, please refer to the paragraph 3.3.7 Speed dial...
FXS-08 Technical Manual EN-V2.0a 3.3.2 SIP Advanced Setting Local SIP port (1~65535) Specify the local SIP port’ s number. Local RTP port (1~65535) Specify the local RTP port’ s number. Session Expire(Sec) Specify the session expire time that will be used to negotiate with the remote host or proxy.
Page 25
FXS-08 Technical Manual EN-V2.0a refresher=uac or uas in the Session Refresh Request message. Unregister All Send SIP unregister signaling message after the FXS-08 has been restarted Early media Treatment Use early media treatment SIP protocol, where SIP invite messages will not include SDP. Support SIP Ping Special feature used with only Nortel’s SIP proxy.
Page 26
FXS-08 Technical Manual EN-V2.0a does not receive a response within 10 seconds, it will cancel the call. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes.
FXS-08 Technical Manual EN-V2.0a 3.3.3 Payload Type Setting RFC2833 payload type Specify the RFC2833 payload type (range is 96~128, however 100, 102~105 is reserved by other payload types). T.38 FAX payload type Specify the FAX payload type (range is 96~128, however 100, 102~105 is reserved by other payload types) T.38 Redundancy payload type Specify the Redundancy payload type...
Page 28
FXS-08 Technical Manual EN-V2.0a other payload types). Modem relay payload type Specify the Modem relay payload type (range is 96~128, default value is 105. 100, 102~104 is reserved by other payload types). Press the “Apply” button (at the bottom) after you finish to save changes. 4.
FXS-08 Technical Manual EN-V2.0a 3.3.4 Line Setting Representative Forward Specify the Representative forwarding type to use, you can choose the following: Disable Unconditional Busy...
Page 30
FXS-08 Technical Manual EN-V2.0a No Answer The “Disable” option will allow you to disable this particular function. Representative Forward Number Specify the number to forward the call to when the call forwarding feature is enabled. No Answer Forward Time If you enable the No Answer Forward function (Representative number or L1~L8 number), please specify the time of no answer.
Page 31
FXS-08 Technical Manual EN-V2.0a to when the call forwarding feature is enabled. Reg. Displays the registration status, whether it is registered or not. Status Displays the line status, whether it is ready (Idle) or busy. Call transfer Enable/Disable per-line Call transfer function.
FXS-08 Technical Manual EN-V2.0a 3.3.5 Qos Setting Type Select Qos Type: DSCP or ToS Differentiated Services Code Point Setting (DSCP) DSCP RTP Select the DSCP value for RTP (voice packets), the value in the drop down list is expressed in binary format, you can choose the following:...
Page 33
FXS-08 Technical Manual EN-V2.0a DSCP Signal Select the DSCP value for SIP message, the value in the drop down list is expressed in binary format, you can choose the following: ToS Setting ToS RTP Select the ToS value for RTP (voice packets), the value in the drop down list is expressed in binary format, you can choose the following:...
Page 34
FXS-08 Technical Manual EN-V2.0a Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes.
FXS-08 Technical Manual EN-V2.0a 3.3.6 NAT Setting IPSharing Mode Select IPSharing mode : Enable or Disable IPSharing Address Specify the IPSharing Address when the IPSharing feature is enabled. Press the “Apply” button (at the bottom) after you finish to save changes. 2.
FXS-08 Technical Manual EN-V2.0a 3.3.7 Speed Dial Setting 3.3.7.1 Speed Dial Speed Dial Editor Specify the speed Dial Number/Telephone Number/Name, then press the Add or Del button to add or delete record...
FXS-08 Technical Manual EN-V2.0a 3.3.7.2 Internal Extension Note: The speed dial function can be used as Internal Extension when the Ethernet is fail. For example : 1. When the FXS-08’ s IP is fixed IP 192.168.123.1, you can set the speed dial as the figure shown above (please be informed that the speed dial number should be the same with SIP setting number and the format of “Telephone Number”...
FXS-08 Technical Manual EN-V2.0a 3.3.7.2 Peer to Peer call Speed Dial Editor Specify the speed Dial (In P2P application) Number/Telephone Number/Name, then press the Add or Del button to add or delete record The format of “Telephone Number” is “#@ipaddress”, for example 1000@192.168.123.1...
FXS-08 Technical Manual EN-V2.0a 3.3.8 Caller ID Setting Caller ID Setting (Line 1~Line 8) Select the (Line 1~Line 8)Caller ID generation type to use, you can choose the following: Disable DTMF FSK(Bellcore) ETSI(Before Ring) ETSI(Between ring) AUTO: You can choose different caller ID type by line.
Page 40
FXS-08 Technical Manual EN-V2.0a DTMF Caller ID Start Symbol Specify the DTMF Caller ID Start Symbol The default symbol is D. DTMF Caller ID End Symbol Specify the DTMF Caller ID End Symbol The default symbol is C. Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot”...
FXS-08 Technical Manual EN-V2.0a 3.3.9 CDR Setting CDR mode Select the CDR mode for Enable or Disable. If you Enable this feature, please specify the CDR Server address and port number at the CDR server address and port’ s text box, then you can get Call Detail Data form CDR Server.
FXS-08 Technical Manual EN-V2.0a 3.3.10 Syslog Setting Syslog mode Select the Syslog mode for Enable or Disable. If you Enable this feature, please specify the Syslog Server address and port number at the Syslog server address and port ’ s text box, then you can get detail system log from Syslog server.
FXS-08 Technical Manual EN-V2.0a 3.4 Advanced Configuration 3.4.1 System setting prack PRACK is defined in RFC 3262: Reliability of Provisional Responses in SIP. You can accommodate your softswitch (Proxy Server) to Enable or Disable this feature. Receiver-Off-Hook (ROH) Tone A ROH tone is sent to the subscriber to inform him that his receiver is off-hook.
Page 44
FXS-08 Technical Manual EN-V2.0a Protocol (SDP). You can Enable/Disable this option. FAX redundancy depth Specify the resend times (0~3)for FAX error packet, T.38 FAX Type Select the FAX Type to use, you can choose the following: T.38 ByPass Auto T.30 FAXByPass Codec Select the FAX ByPass Codec to use, you can choose the following: G.711 a-law...
Page 45
FXS-08 Technical Manual EN-V2.0a 1~5sec. FAXByPass Keyword Some SIP Proxy need specify special keyword for FAXByPass function. Input the data as SIP Proxy required. FAXByPass Keyword Some SIP Proxy need specify special keyword for FAXByPass function. Input the data as SIP Proxy required. IP Address announcement You can Enable/Disable this function, If you select Enable, you can connect...
Page 46
FXS-08 Technical Manual EN-V2.0a line to PSTN. The default setting is “Disable”, if you are not using this particular special application mentioned above, please do not enable this function. ping ip to keep alive network Specify the IP for pinging to make sure the network keeps alive.
FXS-08 Technical Manual EN-V2.0a 3.4.2 SNTP Setting SNTP mode Select the SNTP mode : On or Off SNTP server address Specify the SNTP server address for time synchronization. Time Zone -GMT Select the Time Zone of your location Time setting You can specify the time with year/month/date /hour/minute /second when you select the SNTP...
FXS-08 Technical Manual EN-V2.0a 3.4.3 Codec Setting Codec Priority You can specify the priority of the codec from First to Fifth (first being the highest priority and Fifth being the lowest). You can choose the following codecs: G711U G711A G723 G729 G726 Codec Packet Size...
Page 49
FXS-08 Technical Manual EN-V2.0a shown above, system will set default requirement of bandwidth. Press the “Apply” button (at the bottom) after you finish to save changes. Press the “Reboot” button to apply the changes.
FXS-08 Technical Manual EN-V2.0a 3.4.4 Voice Setting Jitter Buffer Minimal Delay Specify the minimal delay of the jitter buffer. The range is 0~150 ms and the default setting is 0 ms. Maximal Delay Specify the maximal delay of the jitter buffer.
Page 51
FXS-08 Technical Manual EN-V2.0a lines. Remote receive volume Specify the volume gain of the voice in the remote side (0~63, default is 32). You can set this option for each of the 8 lines. DTMF volume Specify the volume gain of the DTMF (0~63, default is 27).
FXS-08 Technical Manual EN-V2.0a 3.4.5 Tone Setting Dial tone Specify the pattern of the Dial tone, you can adjust the high frequency, low frequency, high level, low l evel, the On and Off time for tone 1 and 2. Ringback tone Specify the pattern of the Ringback tone, you can adjust the high frequency, low frequency, high level,...
Page 53
FXS-08 Technical Manual EN-V2.0a frequency, high level, low level, the On and Off time for tone 1 and 2. ROH Tone Specify the pattern of the ROH Tone, you can adjust the high frequency, low frequency, high level, low level, the On and Off time for tone 1 and 2.
FXS-08 Technical Manual EN-V2.0a 3.4.6 Phone Setting Primary Ringing Ringing Frequency Specify the Ringing frequency value. ringing frequency : 15~100 (Unit : Hz) Ringing ON Specify the Ringing ON value . ringing ring ON : 0~8000 (Unit : ms) Ringing OFF Specify the Ringing OFF value.
Page 55
FXS-08 Technical Manual EN-V2.0a Ringing ON Specify the Ringing ON value. ringing ring ON : 0~8000 (Unit : ms) Ringing OFF Specify the Ringing OFF value. ringing ring OFF : 0~8000 (Unit : ms) Ringing level Specify the ringing level. ringing level : 0 ~ 94 (Unit : V) Min.
FXS-08 Technical Manual EN-V2.0a 3.4.7 Digit Manipulation Digit Manipulation Testing This option allows users to test dial a number and check the resulting dialed number and its routing path that is edited by the Digit Manipulation Editor function (see Digit Manipulation Editor section below for more information on it).
Page 57
FXS-08 Technical Manual EN-V2.0a Second Example Prefix: 7 Drop: Disable Insert: 886 Route: VOIP If the user dials 778, the resulting dial out number will be 886778. Third Example (Only applicable for WG2680 FXO) Prefix: 8226 Drop: Disable Insert: 02 Route: PSTN (Only applicable to WG2680 FXO) If the user dials 82265699, the...
FXS-08 Technical Manual EN-V2.0a 3.4.8 Dial Plan Dial Plan Editor Using this feature, users can specify the number that will be immediately dialed out without having to press the “#” (at the end of the dialed number) on the keypad or until the dial time timeout period.
Page 59
FXS-08 Technical Manual EN-V2.0a Total digit count: 8 Route: VOIP If the user dials an 8 digit number (e.g. 82265699), the FXS-08 will immediately detect it and dial this number straight away. Third Example Function: Disable Leading digit: 02 Total digit count: 10 Route: VOIP If the user set the Function parameter as “Disable”, the call number with a...
FXS-08 Technical Manual EN-V2.0a 3.5 Management 3.5.1 Provision Server Note: The provision function is only compatible with some proprietary provision server. If you need this requirement, please contact with your agent. Provision server Mode Enable/Disable provision function Provision server IP address Specify the Provision Server’...
FXS-08 Technical Manual EN-V2.0a 3.5.2 Save-Reload setting Export File Click the “Export ” button to export “user.cfg” data Import File Specify the file path and file name to Import the configure data. Press the “Reboot” button to apply the changes.
FXS-08 Technical Manual EN-V2.0a 3.5.3 Upgrade Firmware Download mode Select the connection method to update the FXS-08’ s firmware, you can choose the following: TFTP TFTP/FTP server IP address Specify the TFTP/FTP server’ s IP address. FTP login Specify the login username/password for the FTP server.
FXS-08 Technical Manual EN-V2.0a 3.5.3.1 Updating the firmware by FTP 1. Select FTP mode in the drop down list. 2. Key in the IP address, login name, password of your FTP server and specify the correct filename of the firmware. 3.
FXS-08 Technical Manual EN-V2.0a 3.5.3.2 Updating the firmware by TFTP 1. First, download the TFTP program from our website http://www.welltech.com/support/utility.htm. Unzip the TFTP to a directory that you desire in your hard drive and execute the TFTP program. Make sure that the TFTP program points to the directory of where your firmware is stored.
FXS-08 Technical Manual EN-V2.0a 3.5.3 3 Updating the firmware by HTTP 1. Under Device Management => Software Upgrade web menu, specify the location of the firmware by clicking the Browse button next to the Http Upload text box. 2. You will be prompted with a window requesting the location of the firmware. 3.
FXS-08 Technical Manual EN-V2.0a 3.5.4 Reset to Default Users can restore back to factory default settings using this feature. The password of the account and the network configurations are the things that will not be changed when this feature is executed.
FXS-08 Technical Manual EN-V2.0a 3.5.5 Network Status Connection mode Displays the current connection mode. Current IP address Displays the current IP address of the WAN port. Subnet mask Displays the current subnet mask’ s IP. Default gateway Displays the current default gateway’ s Primary DNS address Displays the current primary DNS address.
FXS-08 Technical Manual EN-V2.0a 3.5.6 Version Info. Boot version Displays the current boot version loaded on the FXS-08. Post version Displays the current post version loaded on the FXS-08. Application version Displays the current application version loaded on the FXS-08.
FXS-08 Technical Manual EN-V2.0a 3.5.7 Port Status Item Displays the corresponding port number. Status Displays the status of the port. Port Type Displays the port type (FXS,FXO)of the corresponding port number. Register Displays the registration status of the corresponding port number.
FXS-08 Technical Manual EN-V2.0a 3.5.8 Password Username Select the type of user name that you would like to configure the password for, you can choose the following: root user Current password Specify the current password for the user selected in the drop down list above.
FXS-08 Technical Manual EN-V2.0a 3.6 Rebooting the system Executing this function will reboot the whole system, when configuration changes are made to the device, it needs to be rebooted for the changes to take effect (see figure below).