Table of Contents
Advertisement
Quick Links
Rotary Cutter
SC2660 & SC2672 Skid Steer
24538
Table of Contents
Read the Operator's Manual entirely. When you
!
see this symbol, the subsequent instructions and
warnings are serious - follow without exception.
Your life and the lives of others depend on it!
Cover photo may show optional equipment
not supplied with standard unit.
© Copyright 2012
326-025M
Operator's Manual
4/24/12
Printed
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Land Pride SC2672
Summary of Contents for Land Pride SC2672
- Page 1 Rotary Cutter SC2660 & SC2672 Skid Steer 24538 Table of Contents Read the Operator’s Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Cover photo may show optional equipment not supplied with standard unit.
-
Page 2: Table Of Contents
Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. -
Page 3: Look For The Safety Alert Symbol
For Your Protection Thoroughly read and understand the “Safety Label” section, read all instructions noted on them. SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. - Page 4 Flashing warning lights and turn signals are recommended whenever driving on public roads. SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents Getting On and Off Safely Before leaving the operator’s seat: Lower lift arms and put attachment flat on the ground.
- Page 5 Wearing protective equipment such as safety shoes, safety glasses, hard hat, and ear plugs is highly recommended. SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Avoid High Pressure Fluids Hazard Escaping fluid under pressure can penetrate the skin causing serious injury.
-
Page 6: Safety Labels
Read and follow their directions. Keep all safety labels clean and legible. Replace all damaged or missing labels. To order new labels go to your nearest Land Pride dealer or visit our dealer locator at landpride.com. Some new equipment installed during repair requires safety labels to be affixed to the replaced component as SC2660 &... - Page 7 Safety Combo Danger: Keep Hands & Feet Away Danger: Thrown Object Hazard Danger: Rotating Blade Hazard Warning: General Safety Notice: Read Manual - Observe Safety Messages 24538 818-831C Warning: High Pressure 25777 SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M...
- Page 8 Important Safety Information SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents 24539 24539 ROTATING DRIVELINE KEEP AWAY! 25777 25777 818-798C Warning: Pinch Point Hazard 3-Places 818-552C Danger: Rotating Driveline (SC2672 Only) 818-543C Danger: Guard Missing (SC2672 Only)
-
Page 9: Using This Manual
The addition of a Land Pride SC2660 or SC2672 Skid Steer Rotary Cutter to your arsenal of skid steer attachments will dramatically increase the versatility and value of your personal skid steer investment. -
Page 10: Further Assistance
This information is necessary to provide you with quality customer service. If customer service or repair parts are required contact a Land Pride dealer. A dealer has trained personnel, repair parts and equipment needed to service the Rotary Cutter. -
Page 11: Section 1: Assembly & Set-Up
The Skid Steer MUST be equipped with a protective door shield. A universal Operator Protective Door shield is available from Land Pride or owner may chose to use a protective door provided by their skid steer supplier. Refer to Page 13 and 22 for additional information and Land Pride installation instructions. -
Page 12: Sc2660 Motor And Hose Assembly
Skid Steer. See “Motor and Hose Assembly” on page 21 to properly select a motor that matches your Skid Steer. SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents Refer to Figure 1-3: 1. Remove fasteners (#9 & #10) and coupling guard (#8). -
Page 13: Hydraulic Hose Hook-Up
Bottom Slots Height Adjustment Safety Chain (Attach to Skid Steer’s lower hitch loop.) Skid Steer Hook--Up Figure 1-5 SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Zip tie hydraulic hoses together 24", 43" & 63" from male and female coupler ends. -
Page 14: Gauge Wheel Assembly (Optional)
Finger tighten nut only. Gauge Wheel Assembly Figure 1-6 SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents 3. Check alignment of gauge wheel front mount holes with chain guard holes. Skip to step 4 if mounting holes are in alignment. -
Page 15: Operator Protective Door (Optional)
Table of Contents plow bolts plow bolts (#2), 24546 Skid Steer Hand Hold SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Skid Shoe Replacement Figure 1-7 If needed, Locate & Cut Notches in Door For U-bolts Clearance. Hook Elastic Tie-Down To Skid Steer Cage To Keep Door Closed. -
Page 16: Hitch Mounted Centered
24548 SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents Hitch Mounted Centered 1. Drive roll pins (#7) through one of two holes in both pivot pins (#8). -
Page 17: Height Adjustment Safety Chain
5. Tighten quick link coupler nut to secure safety chain. Ratchet Jack Bottom of Rear Skid Shoes Ground Level Nominal Cutting Height Figure 2-2 SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Cutter Hitch Plate Quick Link Coupler Height Adjustment Safety Chain 16 1/2" Maximum Lift... -
Page 18: Deck Leveling With Optional Gauge Wheel
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents 1. Park Skid Steer with cutter on a level surface. 2. Adjust ratchet jack to raise gauge wheel up until it is even with bottom of front skid shoes. -
Page 19: Deck Leveling Without Optional Gauge Wheel
Ground Level Nominal Cutting Height Figure 2-4 SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Cutter Hitch Plate Height Adjustment Safety Chain The rear deck corner should be raised slightly higher above ground level than the front deck corner. -
Page 20: Section 3: Operating Procedures
DANGER Do not cut on steep inclines. The tractor could flip over causing damage to the equipment, serious injury or death. SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents DANGER Do not operator the cutter with cutting blades raised higher than 18"... -
Page 21: Transporting
General Operating Instructions It is absolutely essential that you read and understand both the Operator’s Manual for Land Pride’s Skid Steer Rotary Cutter and the Operator’s Manual for the Skid Steer unit you intend to attach it to before attempting to operate or cut with this combination of equipment. -
Page 22: Rotary Cutter Operating Instructions
Skid Steer unit. Land Pride does offer a protective door with the SC2660 and SC2672 if one is not provided by your skid steer supplier. If the Skid Steer is to be operated on local... -
Page 23: Section 4: Optional Equipment
Skid Steer, you should replace it with one of the following assemblies: 4/24/12 Table of Contents Gauge Wheel Assembly Motor and Hose Assembly SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M 24549 Figure 4-1 24588 Skid Shoe Bundle Figure 4-2... -
Page 24: Optional Case Drain Coupling
Operator Protective Door Refer to Figure 4-6: Land Pride’s Protective Door Kit ..326-024A The Skid Steer MUST be equipped with an Operator Protective Door for shielding against flying debri when attached to a Rotary Cutter. -
Page 25: Section 5: Maintenance & Lubrication
Land Pride Dealer. The parts on your cutter have been specially designed and should only be replaced with genuine Land Pride parts. Do not alter the cutter in a way which will adversely affects its performance. -
Page 26: Skid Shoe Maintenance
312-089D BLADE SPACER 20 GA. (.036") 312-808C BLADE SPACER 24 GA. (.024") 820-112C SC2660 CUTTER BLADE 1/2 x 4 x 25 CW 820-249C SC2672 CUTTER BLADE 1/2 x 4 x 29 CW 316-124H WELDMENT DISHPAN SC2660 312-811H WELDMENT DISHPAN SC2672... -
Page 27: Hydraulic Maintenance
23. 3. Inspect for loose, damaged, or worn parts and adjust or replace as needed. 4. Repaint parts where paint is worn or scratched to prevent rust. Ask your dealer for Aerosol Land Pride touch-up paint. Part No. 821-011C 821-002C 5. -
Page 28: Gauge Wheel Spindle & Axle Hub
Section 5: Maintenance & Lubrication Lubrication Points Lubrication Multi-purpose Legend spray lube SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents Multi-purpose Multi-purpose grease lube oil lube 24539 Lubrication Points Hitch Plate Pivot 2 - Zerks Type of Lubrication: Multi-purpose Grease... -
Page 29: Motor Spindle Hub (Sc2660 Only)
IMPORTANT: Your cutter is shipped with a vented dipstick packaged in the Operator’s Manual bag and should have been installed in the gearbox by your Land Pride dealer. Please see your Land Pride dealer if vented dipstick was not included. 4/24/12... -
Page 30: Section 6: Specifications & Capacities
High Volume Motor Blade Tip Speed Front Deck Protection Rear Deck Protection Deck Lift Height Protection Operator Protection (Optional) Cutting Height Gauging (Optional) SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents SC2660 1004 lbs. 114 lbs. Standard skid shoes = 15 lbs. - Page 31 Table of Contents Section 6: Specifications & Capacities 26819 4/24/12 SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M...
-
Page 32: Section 7: Features & Benefits
Customer can chose one of three optional motors for his SC2660 cutter or one of two optional motors (medium and high volume) for his SC2672 cutter. This allows the cutter to fit a wide variety of Skid Steers. Also the deck can be upgraded to a different motor when owner upgrades his Skid Steer. -
Page 33: Section 8: Troubleshooting
Soil abrasive. Cutting too low. Locked blades. Blades have unequal weight. Blade carrier bent. SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Solution Replace lower seal of motor. Check motor return hose for kinks. Connect case drain line to the hydraulic motor and skid steer reservoir. -
Page 34: Section 9: Torque Values Chart
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above. Wheel Hub Stub 1/2"-20x1 5/8Gr 5 Blade Bolt Lock Nut Blade Carrier Hub Nut SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M Table of Contents Bolt Size (Metric) -
Page 35: Section 10: Warranty
This Warranty does not apply to any part or product which in Land Pride’s judgment shall have been misused or damaged by accident or lack of normal... - Page 36 Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.com...
Need help?
Do you have a question about the SC2672 and is the answer not in the manual?
Questions and answers