Table of Contents
Advertisement
Section 1: Assembly & Set-up
Hitch Hook-Up
Refer to Figure 1-5:
!
DANGER
A Crushing Hazard exists when hooking-up equipment to a
Skid Steer. Do not allow anyone to stand between Skid Steer
and implement while hooking-up to implement. Do not
operate hydraulic controls while someone is near the Skid
Steer or implement.
1. Make sure hydraulic hoses and height adjustment
safety chain do not interfere with hitch hook-up.
2. Drive Skid Steer slowly to the Rotary Cutter making
sure the front hitch plate of the Skid Steer is parallel
with the Rotary Cutter hitch.
3. Tilt top of Skid Steer hitch plate slightly forward.
4. Place top of Skid Steer hitch plate under the Rotary
Cutter top angle bar.
5. Slowly lift Skid Steer's hitch until Rotary Cutter's
hitch and Skid Steer's top angle bar have come
together.
6. Push lock handles of the Skid Steer down so that the
pins go through the bottom slots of the Rotary
Cutter's hitch and the handles lock down.
7. Loop height adjustment safety chain forward down
and under 2" x 3" tube and then attach to Skid Steer's
lower hitch loop. See "Height Adjustment Safety
Chain" on page 15.
Hydraulic Hose Hook-up
Refer to Figure 1-5:
Two high pressure hydraulic outlets are required for the
hydraulic motor and one outlet for the case drain.
Clockwise
Blade Rotation
Rear Skid Shoe
24538
4/24/12
Table of Contents
!
DANGER
Hydraulic fluid under pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin, it must be treated by a
doctor within a few hours or gangrene may result.
8. If attaching to a Kubota CTL, be sure to route
hydraulic hoses through hose loop mounted on top of
the hitch plate on its left side.
9. Thread hoses through any hose holders that may be
provided on the machine operating the cutter. If
attaching to Kubota CTL, thread hoses through Hose
Stay Kit #S6689. Kubota Hose Stay Kit can be
purchased through your nearest Kubota Dealer. See
your Skid Steer/Tractor Operator's Manual for
instruction on how to use these hose holders.
10. Remove plastic cap from case drain hose and attach
optional coupling to the hose or customer may
supply their own coupler. (See "Optional Case
Drain Coupling" on page 22)
11. Connect case drain hose to reservoir outlet.
12. Connect male and female couplers on the hydraulic
motor hoses to the Skid Steer high pressure outlets.
13. Operate skid steer to check blade rotation. Cutter
blades should rotate clockwise when looking at the
blades from above. If cutter blades are rotating
counterclockwise, switch male and female couplers
and reconnect to skid steer outlets.
14. Zip tie hydraulic hoses together at a distance of
24", 43", and 63" from male and female coupler
ends.
Blade Bolt Access Hole
If connecting hoses to a Kubota CTL, be sure to
route hydraulic hoses through hose loop
mounted on top of the hitch plate on the left side
and Kubota's Hose Stay KIt.
Top Angle Bar
Bottom Slots
Height Adjustment Safety Chain
(Attach to Skid Steer's lower hitch loop.)
Skid Steer Hook--Up
Figure 1-5
SC2660 & SC2672 Skid Steer Rotary Cutter 326-025M
Zip tie hydraulic hoses
together 24", 43" & 63"
from male and female
coupler ends.
Case Drain Line
Male Coupler
Female Coupler
Optional 3/8"
Female Flat
Face Coupler
11
Advertisement
Table of Contents
