Related Manuals for LG LS501
Summary of Contents for LG LS501
-
Page 1: Instruction Manual
Color Video Camera Instruction Manual Models : LS501 Before installing, operating or adjusting this product, please read this instruction booklet carefully and completely. - Page 2 to operate this equipment if an unauthorized change or CAUTION modification is made. RISK OF ELECTRIC REGULATORY INFORMATION: FCC Part 15 SHOCK This equipment has been tested and found to comply DO NOT OPEN with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
- Page 3 Voltage Directive 2006/95/EC. European representative : such as vases, shall be placed on the apparatus. LG Electronics Service Europe B.V. To disconnect power from the mains, pull out the Veluwezoom 15, 17 AE Almere, mains cord plug. When install the product, ensure The Netherlands (Tel : +1-06-547-8940) that the plug is easily accessible.
-
Page 4: Important Safety Instructions
Important Safety Instructions 1. Read these instructions. 11. Only use attachments/accessories specified by 2. Keep these instructions. the manufacturer. 3. Heed all warnings. 12. Use only with the cart, stand, tripod, bracket, or 4. Follow all instructions. table specified by the manufacturer, or sold with 5. -
Page 5: Table Of Contents
Contents Features ......6 Motion Detection setting....0 Cautions for Safe Operation. -
Page 6: Features
Features This color video camera is designed for use in monitoring system. • High resolution and high sensitivity with a 1/ inch Super HAD CCD (Charge Coupled Device). • Line Lock when using AC 4V. (LS501N-B1,P-B1) • Line Lock when using AC 0V. (LS501P-C1) •... -
Page 7: Cautions For Safe Operation
Cautions for Safe Operation Power Supply • Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides. LS501N-B1/LS501P-B1: They may damage the surface finish and/or impair the operation of the camera. This camera must be operated AC 4V or DC 1V Certified/Listed, class power supply only. -
Page 8: Part Names And Functions
Part Names and Functions a Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap a b c before installing a lens. b Flange-back adjustment ring c Camera installation bracket The bracket can be fixed at the top or bot- tom of the camera. - Page 9 Part Names and Functions Lens iris output connector (LENS) This 4- pin connector is used to send the Iris con- trol signal and power supply to an auto-iris type lens. d e f Buttons for menu To set items on the MENU, use the these buttons. ALC Lens Setting Switch •...
- Page 10 Part Names and Functions Power input terminal LS501N-B1 / LS501P-B1 AC 4 V or DC 1 V input terminal. g h i Power indicator Comes on when the power to the camera is on. Video output connector (BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.
- Page 11 Part Names and Functions Power cable (AC 0V) LS501P-C1 Power indicator h i Comes on when the power to the camera is on. Video output connector (BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.
-
Page 12: Connections
Connections Connecting Monitor LS501N-B1 / LS501P-B1 The video signal connection between the camera and Power connection the monitor or DVR. Remove the insulation on the power cable as illus- trated. Attach the terminal tips. Connect to the 4V AC / 1V DC UL Listed, Class Power Supply only on the camera. - Page 13 Connections Basic connection LS501P-C1 The peripheral devices (VCR, monitor, lens, etc.) and cables are not supplied. Connecting the monitor. Make the video signal connection between the camera and the monitor or time lapse VCR. Insert the plug of this power cord into a wall To monitor's Video Input outlet.
-
Page 14: Mounting The Lens
Mounting the Lens Remove the lens mount cap from the camera. Install the auto-iris lens. 2-1. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. 2-2. C mount type lens To allow for flange- back adjustment, install the C-mount adaptor (option) on the lens mount, then carefully align the lens mount with... - Page 15 Mounting the Lens Rewire the lens iris plug Pin layout for the lens iris output connector Cut off the plug of the lens cable, cut off approxi- mately 8mm of the insulation, and then strip approximately mm of the ends of the cable sheaths.
-
Page 16: Concerning Auto-Iris Lenses
Concerning Auto-Iris Lenses DC type auto-iris lens VIDEO type auto-iris lens A lens without driver circuit that operates only on a DC A lens with amplifier circuit that operates on video sig- power source. In general, this type of lens is referred to nal and DC power source. -
Page 17: Flange-Back Adjustment
Flange-back Adjustment The adjustment is required only when a lens without Use the flange-back adjusting ring to obtain a focused focus-adjusting mechanism is mounted, or when a lens point while watching the monitor screen. with adjusting mechanism is mounted and focus that is Note: more accurate is needed. -
Page 18: Installation Of Camera
Installation of Camera The bracket can be installed to either the top of the camera as desired. When changing the position of the camera mounting bracket, you should always reuse the screws that have been removed. Note: If using a camera mounting bracket, select a location that is strong enough to bear the full weight of the camera and the mounting bracket for long periods, and install the camera and mounting bracket securely. -
Page 19: Menu Operation
Menu Operation The following table shows the list of menu items and Main Menu Sub Menu Contents options. You can adapt the camera to your require- LOW/ MIDDLE/ LEVEL ments by setting up the respective items in these HIGH menus. AUTO 5, 10, 15, 0, DWELL TIME... -
Page 20: General Operation
Menu Operation Main Menu Sub Menu Contents Main Menu Sub Menu Contents CAMERA REBOOT MASK AREA1 ~ NUMBER AREA8 RESET FACTORY RESET DISPLAY OFF, ON EXIT RET/TOP/END BLACK, GRAY, COLOR WHITE EXIT PRIVACY HEIGHT WIDTH General Operation MOVE Y MOVE X Press button. - Page 21 Menu Operation button to select a submenu option. button to select a value. Select [EXIT] option then press to exit the setup menu. In the submenu, use button to select the [EXIT] then use button to select a mode and press to exit the setup menu.
-
Page 22: Camera Identification Settings
Camera Identification Settings You can use the camera identification (CAMERA ID) to assign a number to the camera. Select [CAMERA ID] option on the [CAMERA SETTING] menu. to select a CAMERA ID (OFF, 1~55). -
Page 23: Exposure Settings
Exposure settings Exposure mode setting BACKLIGHT setting Backlight compensation increases the exposure level when the camera picture is darkened by the strong background light. Select [BACKLIGHT] option. Select [EXPOSURE] option. button to select a mode. (ALC ELC) Press button. button to select a mode then press Submenu appears on the monitor. - Page 24 Exposure settings BRIGHTNESS setting • HSBLC: Use for adjusting brightness the specific area of picture. The HSBLC mode is You can increase the brightness of the darkened video. automatically activated only in low illuminance If you set the brightness to lower value, the image is scene.
- Page 25 Exposure settings AGC (Automatic Gain Control) setting SHUTTER (Shutter Speed) setting If the images are too dark, change the maximum [AGC] Select the desired shutter speed for camera exposure. value to make the images lighter. You can change the shutter speed to higher speed Select [AGC] option on the [EXPOSURE] menu.
- Page 26 Exposure settings SENS-UP setting Select [SENS-UP LIMIT] option. button to set the SENS-UP limit (x, If pictures are not clear due to darkness, use for ~, x18). increase the sensitivity of picture. Select [SENS-UP] option on the [EXPOSURE] menu. to select [AUTO] option and press button.
-
Page 27: White Balance Setting
White Balance setting Select the method by which the camera shifts its output When the scene contains mostly high color colors to compensate for the color of a light source. temperature objects, such as a blue sky or sunset. Select [WHITE BALANCE] option on the [CAMERA When the scene is dim. - Page 28 White Balance setting > INDOOR: The color temperature range for the proper white balance is approximately ,00°K. > OUTDOOR: The color temperature range for the proper white balance is approximately 5,100°K. RED: Set the desired red value. (-100~100) BLUE: Set the desired blue value. (-100~100)
-
Page 29: Day/Night Setting
Day/Night setting Select [DAY/NIGHT] option on the [CAMERA SETTING] menu. LEVEL: Use button to select a level. button to select mode for day/night (LOW MIDDLE HIGH) function. DWELL TIME: Use button to • AUTO: You will be able to change the Day/ select a dwell time. -
Page 30: Motion Detection Setting
Motion Detection setting The motion detection detects the moving objects in the to select an option then use scene by monitoring changes in brightness level. You button to adjust the option. can select the level of sensitivity for motion detection •... -
Page 31: D-Dnr Setting
3D-DNR setting Select [D-DNR] option. If pictures are not clear due to noise, use this func- tion to reduce the noise of picture. button to select a option. (OFF MIDDLE HIGH) Notes: • If you set the AGC to [OFF] on the [EXPOSURE] menu, the [D-DNR] function is not available. -
Page 32: Privacy Mask Setting
Privacy Mask setting This function is aiming at the protection of personal pri- button to select the color of the mask vacy, selecting a screen part black not to be displayed zone box on the [COLOR] option. in the screen. Up to 8 zones can be registered. to select an option then use Select [PRIVACY] option on the [CAMERA button to adjust the option... -
Page 33: Special Menu Settings
Special menu settings Setting the D-ZOOM (Digital Zoom) level D-EFFECT (Digital effect) setting You can select the digital zoom level. You can select the digital effect. Select [D-ZOOM] option on the [SPECIAL] menu. Select [D-EFFECT] option on the [SPECIAL] menu. button to select a digital effect. - Page 34 Special menu settings SHARPNESS setting Stabilizer setting Sharpens the image outline. Select [SHARPNESS] option on the [SPECIAL] menu. The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration. This function is useful for outdoor surveillance. button to change a adjust the option. If you set the sharpness value to higher, the image Select [STABILIZER] option and set to ON or OFF.
- Page 35 Special menu settings COLOR setting The SYNC function is available only with AC power source. You can switch the displayed picture to grayscale or Select [SYNC] option on the [SPECIAL] menu. color. Select [COLOR] option on the [SPECIAL] menu. button to select [INT] or [LL]. button to change a color effect.
- Page 36 Special menu settings User title setting button to select a character or number. You can use the camera identification to assign a num- CLR: If you enter the wrong code, select CLR ber and character to the camera (0 - 9, A-Z, a-z). then press To disappear the user title, select [OFF].
- Page 37 Special menu settings Language setting Select a language for setup menu and information display.
-
Page 38: Reset Settings
Reset settings Select [RESET] option. Press button and the RESET menu appears. to select option. • CAMERA REBOOT: Reboot the camera sys- tem. • FACTORY RESET: Clear certain settings and information and return to factory default set- tings. Press to confirm your selection. -
Page 39: Specification
Specification Model LS501N-B1 LS501P-B1 LS501P-C1 Signal System NTSC Total/Effective Pixels 410K/80K 470K/440K 470K/440K Image Device 1/" Super HAD CCD Lens CS Mount (C Mount using adaptor ring) Iris Control DC / VIDEO Synchronization System Internal/Line Lock Scanning Frequency (H) 15.74 KHz 15.65 KHz 15.65 KHz Scanning Frequency (V) - Page 40 Specification Model LS501N-B1 LS501P-B1 LS501P-C1 Video Output Signal 1.0 Vp-p Composite (75 ohm) Auto Gain Control Low/Middle/High/Off Day & Night Day/Night/Auto Electric Shutter Speed 1/60 - 1/90,000 1/50 - 1/90,000 1/50 - 1/90,000 White Balance ATW / AWC->PUSH / MANUAL Stabilizer (EIS) OFF/ON D-DNR...