Siqura FD820 Quick Start Manual

Siqura FD820 IP Cameras
High-Definition Fixed-Dome Style

Quick Start Guide

Step 1: Product Inventory

Before you proceed, make sure that your FD820 package contains the
items listed below.
FD820 camera Self-tapping screws (x4)
Plastic screw anchors (x4)
Rubber washers (x6)
Power terminal block CD (manuals
and search tool)
Figure 1 FD820 package contents

Step 3: Powering Up

Figure 5 FD820 Printed Circuit Board (PCB)
connectors
To power the FD820 with AC24V/DC12V
 Connect to the DC/AC power source as
indicated in table 1 and figure 5.
 Note that the supplied DC power
adapter is for indoor use only.
To power the FD820 with PoE
 Connect the RJ-45 connector to an appropriate PSE network switch.
 Use Cat 5 Ethernet cable that does not exceed 100 meters in length.
Connect to a hub or switch with straight-through cable. Use crossover
cable to connect directly to a PC.
Note that PoE cannot be used with the heater.
© Siqura B.V. 2012
Version 1.0 (120105-1)
FD820 QSG (MW07SP2)
FD820 cameras can be installed directly on a wall or ceiling.
 Make sure that the provided surface has sufficient strength to support the camera.
 If you use Power over Ethernet (PoE), check that there is adequate access to an IEEE 802.3AF Power Sourcing Equipment (PSE) enabled network.
Step 1: Remove the camera from the dome housing
1. Use the supplied security TORX to unscrew the:
- housing cover
1.5A power adapter - camera from the housing
(indoor use only)
2. Gently press both sides of the inner cover and
remove it from the dome unit (figure 2 – left).
3. Press the snap-on sides of the camera and
detach it from the dome housing (figure 2 –
Security TORX
right).
Quick Start Guide
Figure 2 Remove the inner cover (left) and detach
the camera from the dome housing
The internal settings of the FD820 can be accessed directly via a
web interface.
 Use only Internet Explorer 6.x or higher.
 The IP camera's default IP address is printed on a label located on
the bottom of the camera.
 The default logon user name and password are Admin / 1234. Both
Connector Pin Definition
are case sensitive.
DC 12V 1 Power
2 Reserved
To access the camera's internal settings
3 GND  Type the IP address of the camera in the address bar of your web
AC 24V 1 Power-1 browser (figure 6).
2 GND
3 Power-2
Table 1 Power connector pin
definitions
Figure 6 Entering the IP address of the camera into the address bar of your
To view the webpages of the camera properly
 Install the add-on, Siqura Viewer.
 Enable ActiveX controls.

Step 2: Hard Wall or Ceiling Installation

Step 2: Mount the dome housing

Step 3: Connect the cables
1.
2.
Step 4: Insert the snap-on module into the dome housing


Step 4: Accessing the Camera

browser
www.siqura.com
www.tkhsecurity-usa.com
Attach the dome housing to the wall or ceiling with
the supplied screws and screw anchors.
Thread the power, Ethernet, and possibly audio and
alarm device cables through the side or back conduit
entry (figure 3).
Connect the cables to the FD820.
Snap the camera back into the dome housing
(figure 4).
Figure 4 Reattach the camera to the
dome housing

Step 5: Device Search

Use the Device Search application to discover and
change the IP address of the camera.
DeviceSearch.exe can be found on the supplied CD or at
www.siqura.com. This application detects and lists all the
Siqura IP cameras found on the network.
To explore your network for installed devices
1. Start the Device Search application.
2. Click the button.
Device Search
If a security alert window displays, click
3. Right-click a device and select
settings of the camera via a web interface.
Figure 7 Click Browse to open the webpages of the camera
Figure 3 Connect the cables and lead
them through the conduit entry
to continue.
Unblock
to access the internal
Browse