Page 1
60-150 1.5 HP Dust Collector 4001824 Operator’s Manual Record the serial number and date of purchase in your manual for future reference. Serial Number: _________________________ Date of purchase: _________________________ For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167 www.rikontools.com...
Changes and improvements may be made at any time, with no obligation on the part of Rikon Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety,...
Page 3
SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fi re, and/or serious personal injury. There are certain applications for which this tool was designed.
Page 4
SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF”...
SAFETY INSTRUCTIONS ELECTRICAL SAFETY EXTENSION CORDS THIS TOOL MUST BE GROUNDED THE USE OF AN EXTENSION CORD WITH THIS MACHINE IS NOT RECOMMENDED. For WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK. best power and safety, plug the machine directly into a dedicated, grounded electrical outlet that is within the IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, supplied cord length of the machine.
SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR DUST COLLECTORS This machine is intended for the collection of chips, shavings and dust from the surfacing, cutting and sanding of natural wood, plywood, plastics and other man-made wood based composites. It is for collecting DRY materials only.
Hex Wrenches - 4mm, 5mm ( not shown ) Model 60-150 1.5HP Dust Collector is shipped complete in one box. Unpacking and Clean-up 1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material.
ASSEMBLY INSTALL THE CASTERS ON THE BASE PLATE Locate the four swivel casters, eight 12MM flat washers, four star lock washers and four 12MM hex cap nuts from the hardware pack. NOTE: Some of these fasteners may be already mounted on the caster stems.
Page 9
ASSEMBLY INSTALL THE 5” OUTLET AND RUBBER GASKET Locate the 5” plastic outlet, rubber gasket, six M6X- 20MM hex bolts, twelve 6MM washers, and six nuts. 1. Place the rubber gasket on the flange of the fan housing so that the 6 holes align with the 6 holes in the fan housing.
Page 10
ASSEMBLY INSTALL THE 5” HOSE Locate the 5” hose and two hose clamps. 1. Slip a hose clamp (A) over both ends of the hose. 2. Place one end of the hose over the 5” outlet on the fan housing and the other end on the collector. FIG. 8. 3.
ASSEMBLY MOUNTING THE ‘Y’ INLET 1. Slide the ‘Y’ inlet over the large 5” opening on the fan housing, so that the three mounting holes align. 2. Secure the ‘Y’ inlet in place with the supplied three Phillips head screws and washers. FIG. 11. 3.
PARTS DIAGRAM 60-150 DUST COLLECTOR NOTE: Please reference the Key Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required. 25 26 22 23...
WIRING DIAGRAM This machine must be grounded. Replacement of the power supply cable should only be done by a qualifi ed electrician. See page 5 for additional electrical information. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION 1. Plug cord into electrical outlet. 1.
MAINTENANCE Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance. 1.
Page 16
60-150 For more information: 16 Progress Road Billerica, MA 01821 877-884-5167 / 978-528-5380 techsupport@rikontools.com www.rikontools.com 60-150M1...