Table of Contents
Advertisement
Quick Links
60-101
Wall Mounted
1HP DUST COLLECTOR
Operator's Manual
Record the serial number and date of purchase in your manual for future reference.
The serial number can be found on the specification label on the side of your machine.
Serial Number: _________________________
Date of purchase: _________________________
For technical support, email techsupport@rikontools.com - For parts questions, email parts@rikontools.com
www.rikontools.com
60-101M1
Advertisement
Table of Contents
Related Manuals for Rikon Power Tools 60-101
Summary of Contents for Rikon Power Tools 60-101
- Page 1 60-101 Wall Mounted 1HP DUST COLLECTOR Operator’s Manual Record the serial number and date of purchase in your manual for future reference. The serial number can be found on the specification label on the side of your machine. Serial Number: _________________________ Date of purchase: _________________________ For technical support, email techsupport@rikontools.com - For parts questions, email parts@rikontools.com...
-
Page 2: Table Of Contents
Changes and improvements may be made at any time, with no obligation on the part of Rikon Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety,... -
Page 3: Safety Warnings
SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this tool was designed. - Page 4 SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF”...
-
Page 5: Electrical Requirements
SAFETY INSTRUCTIONS EXTENSION CORDS ELECTRICAL SAFETY THE USE OF AN EXTENSION CORD THIS TOOL MUST BE GROUNDED WITH THIS MACHINE IS NOT RECOMMENDED. For WHILE IN USE TO PROTECT THE OPERATOR FROM best power and safety, plug the machine directly into a ELECTRIC SHOCK. -
Page 6: Dust Collector Safety Rules
SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR DUST COLLECTORS This machine is intended for the collection of chips, shavings and dust from the surfacing, cutting and sanding of natural wood, plywood, plastics and other man-made wood based composites. It is for collecting DRY materials only. -
Page 7: Contents Of Package
- Hose Clamps Hex Wrench 3mm Model #60-101 Wall Mounted 1HP Portable Dust Collector is shipped complete in two boxes. Unpacking and Clean-up 1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material. -
Page 8: Assembly
ASSEMBLY NOTE: The parts listed in the instructions refer to THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE either the Contents of Package on page 7, or the OFF POSITION UNTIL ASSEMBLY IS COMPLETE. Parts Diagram &... - Page 9 ASSEMBLY MOUNTING THE ‘Y’ INLET Locate the following parts: 4” ‘Y’ Dust Fitting with Cap (F, Parts List #46,47) - Phillips Screw (#45) - Phillips Screwdiver (not included) 1. Slide the ‘Y’ Inlet (#46) over the large 5” opening on the fan housing, so that the mounting hole aligns. 2.
- Page 10 Please visit your local machine dealer for dust collection supplies. The 60-101 Dust Collector includes a 5” diameter dust hose inlet on its fan cover. 5” dust hoses can be clamped directly onto this large inlet. See Figure 9.
-
Page 11: Operation
Clear plastic lower bags for the collection and disposal of the dust and debris from the dust collector. Bags fit the 60-101 Dust Collector Canister’s 19-5/8” (500mm) diameter. Bag capacity approx 1.5 cu/ft. To order replacement parts or accessories for the... -
Page 12: Parts Diagram
PARTS DIAGRAM 60-101 Wall Mounted DUST COLLECTOR NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required. -
Page 13: Parts List
PARTS LIST PART DESCRIPTION QTY. Canister Filter P60-101-1 Main Spindle P60-101-2 Bearing Fixing Plate P60-101-3 Connecting Spindle P60-101-4 Bevel Gears P60-101-5 Self-lubricating Bearings P60-101-6 Main Housing P60-101-7 Inlet Cover P60-101-8 Aluminum Impeller 10” P60-101-9 Motor P60-101-10 Motor Plate P60-101-11 Wall Mount Bracket P60-101-12 Handle P60-101-13... -
Page 14: Wiring Diagram
WIRING DIAGRAM T1 = Black 240V 60Hz 120V 60Hz T2 = Gray T3 = Red T4 = Yellow This machine must be grounded. Replacement of the power supply cable should only be done by a qualified electrician. See page 5 for additional electrical information. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE... -
Page 15: Maintenance
MAINTENANCE Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance. 1. - Page 16 60-101 For more information: 16 Progress Road Billerica, MA 01821 877-884-5167 / 978-528-5380 techsupport@rikontools.com LINK TO RIKON WEBSITE www.rikontools.com 60-101M1...