1. Manuals
  2. Brands
  3. Rikon Power Tools Manuals
  4. Dust Collector
  5. 60-151C
  6. Operator's manual

Rikon Power Tools 60-151C Operator's Manual

1.5 hp dust collector
Hide thumbs

Advertisement

Table of Contents

60-151C
®
1.5 HP Dust Collector
Operator's Manual
Record the serial number and date of purchase in your manual for future reference.
Serial Number: _________________________
Date of purchase: _________________________
For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167
www.rikontools.com
60-151CM1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 60-151C and is the answer not in the manual?

Questions and answers

Related Manuals for Rikon Power Tools 60-151C

Summary of Contents for Rikon Power Tools 60-151C

  • Page 1 60-151C ® 1.5 HP Dust Collector Operator’s Manual Record the serial number and date of purchase in your manual for future reference. Serial Number: _________________________ Date of purchase: _________________________ For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167 www.rikontools.com...
  • Page 2 Changes and improvements may be made at any time, with no obligation on the part of Rikon Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety,...

  • Page 3: Safety Instructions

    SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this tool was designed.
  • Page 4 SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF”...
  • Page 5 SAFETY INSTRUCTIONS ELECTRICAL SAFETY EXTENSION CORDS THIS TOOL MUST BE GROUNDED THE USE OF AN EXTENSION CORD WITH THIS MACHINE IS NOT RECOMMENDED. For WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK. best power and safety, plug the machine directly into a dedicated, grounded electrical outlet that is within the IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, supplied cord length of the machine.
  • Page 6 SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR DUST COLLECTORS This machine is intended for the collection of chips, shavings and dust from the surfacing, cutting and sanding of natural wood, plywood, plastics and other man-made wood based composites. It is for collecting DRY materials only.
  • Page 7 Plastic Collection Bag ( not shown ) Model 60-151C 1.5HP Dust Collector with Canister is shipped in two boxes. Unpacking and Clean-up 1. Carefully remove all contents from the shipping cartons. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material.
  • Page 8 Interior Cleaning Flap #2 Phillips Screwdriver Cleaning Flap Handle Model 60-151C 1.5HP Dust Collector with Canister is shipped in two boxes. Unpacking and Clean-up 1. Carefully remove all contents from the shipping cartons. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material.

  • Page 9: Canister Assembly

    CANISTER ASSEMBLY INSTALL THE INTERIOR CANISTER FLAP 1. Insert the Interior Cleaning Flap, Part E FIG.1, with the larger and longer threaded end first, down into the center of the Canister. 2. Place a 15mm flat washer onto the lower, shorter threaded end of the Cleaning Flap.
  • Page 10 ASSEMBLY INSTALL THE CASTERS ON THE BASE PLATE Locate the four swivel casters, eight 12MM flat washers, and four 10MM hex cap nuts from the hardware pack. NOTE: Some of these fasteners may be already mounted on the caster stems. 1.
  • Page 11 ASSEMBLY INSTALL THE COLLECTOR SUPPORTS Locate the three collector supports, six M8X20MM hex bolts and two 8MM washers. The two mount- ing positions in the corners of the Base Plate (A) are threaded and do not require nuts. The third mounting location (B) does not have threads and requires hex nuts FIG.
  • Page 12 ASSEMBLY INSTALL THE 5” HOSE Locate the 5” hose and two hose clamps. 1. Slip a hose clamp (A) over both ends of the hose. 2. Place one end of the hose over the 5” outlet on the fan housing and the other end on the col- lector.
  • Page 13 ASSEMBLY INSTALL THE COLLECTION BAG ON THE COLLECTOR 1. Place the filter Bag Fixing Ring over the top of the Collection Bag. Fold the Collection Bag over the Fix- ing Ring by approximately 3 inches. FIG. 14 2. Insert the Fixing Ring with Bag at an angle all the way into the collector drum.

  • Page 14: Operation

    OPERATION INSTALL THE DUST HOSE For using either 6” or 4” hoses, installing them onto the dust collector fitting(s) and your woodworking machine(s) is the same process. 4” hose shown in the following example. Fig. 17. 1. Slip a hose clamp over both ends of the hose. 2.

  • Page 15: Parts Diagram

    PARTS DIAGRAM 60-151C NOTE: Please reference the Key DUST Number when calling for Replacement Parts. COLLECTOR For Parts under Warranty, the Serial Number of your machine is required.
  • Page 16 PARTS LIST PARTS LIST 60-151C Dust Collector with Cannister PART PART DESCRIPTION DESCRIPTION QUANTITY QUANTITY Spring washer 8 Base P60-151C-1 P60-151C-25 Hex cap nut M8 Type I hex nut M10 P60-151C-2 P60-151C-26 Phillips screw Spring washer 10 P60-151C-3 P60-151C-27 Inlet...

  • Page 17: Troubleshooting

    TROUBLESHOOTING PROBLEM POSSIBLE CAUSE 1. Plug cord into electrical outlet. 1. Machine not plugged in. 2. Lift switch to ‘ON’ position. 2. Power switch in ‘OFF’ position. 3. Replace switch or cord. 3. Power switch or cord is faulty. 4. Correct overloaded electrical circuit. 4.

  • Page 18: Wiring Diagram

    WIRING DIAGRAM This machine must be grounded. Replacement of the power supply cable should only be done by a qualified electrician. See page 5 for additional electrical information. Wiring Diagram - 60-151C Dust Collector...

  • Page 19: Maintenance

    MAINTENANCE Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance. 1.
  • Page 20 60-151C ® For more information: 25 Commerce Way North Andover, MA 01845 877-884-5167 / 978-528-5380 techsupport@rikontools.com www.rikontools.com 60-151CM1...

Table of Contents