Related Manuals for Federal Signal Corporation P-LS2B
Summary of Contents for Federal Signal Corporation P-LS2B
- Page 1 PAGASYS Series Loudspeaker Models P-LS2B, P-LS2B-8, PLS2C, and PLS2C-8 Installation, Operation, and Maintenance Instructions 2562390B REV. B 812 Printed in U.S.A...
- Page 2 blank page...
-
Page 3: Table Of Contents
Getting Technical Service and Support ..........19 Ordering Replacement Parts ..............19 Figures Figure 1 Loudspeaker connections for P-LS2B and P-LS2C .....11 Figure 2 Loudspeaker connections for P-LS2B-8 and P-LS2C-8 ..12 Figure 3 Internal wiring for P-LS2B and P-LS2C ........14 Figure 4 Internal wiring for P-LS2B-8 and P-LS2C-8......15... - Page 4 Tables Table 1 Wattage tap settings ...............13 Table 2 Example serial number ............19 Table 3 Replacement parts ..............19...
-
Page 5: Safety Messages To Installers, Users, And Maintenance Personnel
Safety Messages to Installers, Users, and Maintenance Personnel It is important to follow all instructions shipped with this loudspeaker. This loudspeaker is to be installed by trained personnel who is thoroughly familiar with the country electric codes and will follow these guidelines as well as local codes. -
Page 6: Unpacking The Loudspeaker
PAGASYS loudspeakers are manufactured from corrosion-resistant, anti-static, glass-reinforced polyester (GRP). The total power output capability of the P-LS2B and P-LS2C is 25 W, adjustable down to 0.2 W. The available audio input is 100 Vrms. The P-LS2B-8 and P-LS2C-8 are 8 ohm, 25 W. -
Page 7: Certifications
Certifications ATEX Certificate Number: Baseefa10ATEX0096X IECEx Certificate Number: IECEx BAS 10.0052X Model P-LS2B II 2G 0539 Ex d e mb IIB + H2 T5 Gb (−50 °C ≤ Ta ≤ +70 °C) T6 Gb (−50 °C ≤ Ta ≤ +55 °C) -
Page 8: Specifications
Gland Entries: 2 x M20 x 1.5 mm Cable Terminations: 0.5 mm to 4 mm (22 AWG to 12 AWG Size (P-LS2B and P-LS2C): Diameter: 232.4 mm (9.15 in) Height: 286.2 mm (11.27 in) Length: 318.8 mm (12.55 in) Material:... -
Page 9: Specific Condition Of Use
All drilled holes should be de-burred and all sharp edges should be smoothed. The Models P-LS2B and P-LS2C Series loudspeakers are designed for mounting on a flat horizontal or vertical surface. To mount the loudspeaker, obtain M6 stainless steel bolts, lockwashers,... -
Page 10: Adjusting The Vertical Angle
PAGASYS Series Loudspeaker IMPORTANT: The nameplate, which contains cautionary or other information of importance to maintenance personnel, should not be obscured. Select a mounting location that is capable of supporting more than 6 kg (13.2 lb). Use the mounting bracket as a template to scribe the centers of the mounting holes. -
Page 11: Figure 1 Loudspeaker Connections For P-Ls2B And P-Ls2C
PAGASYS Series Loudspeaker Figure 1 Loudspeaker connections for P-LS2B and P-LS2C REPLACEABLE FUSE MODULE POWER JUMPERS TAPPING GUIDE AUDIO INPUT FROM AMPLIFIER (+IN) EARTH LUG AUDIO TO NEXT TO NEXT INPUT FROM LOUDSPEAKER LOUDSPEAKER AMPLIFIER (–IN) +OUT −OUT 290A6466... -
Page 12: Figure 2 Loudspeaker Connections For P-Ls2B-8 And P-Ls2C-8
PAGASYS Series Loudspeaker Figure 2 Loudspeaker connections for P-LS2B-8 and P-LS2C-8 AUDIO INPUT FROM AMPLIFIER AUDIO INPUT EARTH FROM AMPLIFIER –IN 290A7003 To wire the loudspeaker: Loosen the four screws securing the rear cover to the loudspeaker, and remove the cover. -
Page 13: Setting Transformer Wattage Taps
PAGASYS Series Loudspeaker Setting Transformer Wattage Taps The Model P-LS2B and P-LS2C loudspeakers have ten wattage tap settings that enable you to select the loudness of each loudspeaker in the system (see Table 1 below and Figure 3 on page 14). The higher the wattage tap, the louder the speaker output. -
Page 14: Figure 3 Internal Wiring For P-Ls2B And P-Ls2C
PAGASYS Series Loudspeaker Figure 3 Internal wiring for P-LS2B and P-LS2C... -
Page 15: Figure 4 Internal Wiring For P-Ls2B-8 And P-Ls2C-8
PAGASYS Series Loudspeaker Figure 4 Internal wiring for P-LS2B-8 and P-LS2C-8 290A7001... -
Page 16: Safety Messages To Maintenance Personnel
PAGASYS Series Loudspeaker Safety Messages to Maintenance Personnel FIRE/EXPLOSION HAZARD Do not open the loudspeaker when it is energized. Failure to observe this warning could result in serious injury or death. Listed below are some important safety instructions and precautions you should follow: •... -
Page 17: Periodically Inspecting The Loudspeaker
To avoid an electrical shock, do not connect the loudspeaker to the system while the power is on. FOR MODELS P-LS2B AND P-LS2C ONLY: The loudspeaker is fully encapsulated and the speaker driver is non- serviceable. If the driver fails, the entire loudspeaker must be replaced. -
Page 18: Returning A Product For Credit
PAGASYS Series Loudspeaker Remove the Phillips-head screw securing the fuse module, and remove the module. Reinstall the new fuse module. Replace the rear cover and tighten the screws securing it to approximately 4 N·m (35.4 in-lb). Test the speaker system to verify that it operates properly. Returning a Product for Credit Product returns for credit require a return authorization from your local distributor prior to returning the product to Federal Signal. -
Page 19: Getting Technical Service And Support
PAGASYS Series Loudspeaker Getting Technical Service and Support Products returned for repair require a Return Authorization form. To obtain service for the product, please contact the Federal Signal Service Department at +1 708-534-4858. For technical assistance, please call Federal Signal Technical Support at +1 708-534-3424, extension 5823. - Page 20 Industrial Systems 2645 Federal Signal Drive • University Park, IL 60484-3167 Tel: 708-534-4756 • Fax: 708-534-4852 Email: elp@federalsignal.com • www.federalsignal-indust.com...