Preparation; Starting Sky Command System Ii Operation; Power On Message - Kenwood TS-590SG Instruction Manual

12 OPERATOR CONVENIENCES

PREPARATION

Although you can use a TH-D7A, TH-D72(A/E)/
TM-D710/G(A/E), TM-V71A + RC-D710, or TM-D700A
transceiver as a "Commander" (an external remote
control unit), the following procedure shows how to set
up your TS-590SG and TH-D7A, TH-D72(A/E)/
TM-D710/G(A/E), TM-V71A + RC-D710, or TM-D700A
transceivers as a "Transporter" at a base station and
the TH-D72(A/E)/ TM-D710/G(A/E), TM-V71A + RC-
D710, or TM-D700A transceiver as a "Commander".
STARTING SKY COMMAND SYSTEM II
OPERATION
After you have completed setting up the following, you
can start Sky Command System II operation. Without
programming these parameters, you cannot use Sky
Command System II.
TS-590SG + TH-D7A/ TH-D72(A/E)/ TM-D700A/
TM-D710/G(A/E)/ TM-V71A + RC-D710 (Transporter)
Setup:
1 Confi gure the TH-D7A, TH-D72(A/E)/ TM-D710/
G(A/E), TM-V71A + RC-D710, or TM-D700A as a
"Transporter" and connect all the necessary cables
to the TS-590SG transceiver.
2 Select a frequency (HF/ 50 MHz band) on the
TS-590SG transceiver.
3 On the TS-590SG, press [MENU], then turn
MULTI/CH control to select Menu No. 67.
4 Press [M.IN]/ [SCAN (SG.SEL] to select the
desired communication speed.
5 Select the same communication parameters
to match the TH-D7A, TH-D72(A/E)/ TM-D710/
G(A/E), TM-V71A + RC-D710, or TM-D700A
transceiver.
6 Press [MENU] to exit Menu mode.
7 Confi gure and start the Transporter mode on the
TH-D7A, TH-D72(A/E)/ TM-D710/G(A/E), TM-V71A
+ RC-D710, or TM-D700A transceiver.
• Refer to the respective instruction manuals of
the TH-D7A, TH-D72(A/E)/ TM-D710/G(A/E),
TM-V71A + RC-D710, or TM-D700A for
information on how to connect, confi gure, and
operate the transceivers for Sky Command
System II.
68

POWER ON MESSAGE

Each time you switch the transceiver ON,
"KENWOOD" (default) appears on the sub display
for approximately 2 seconds. You can program your
favorite message in place of the default message. You
can enter a message using up to 8 characters.
1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or
turn the MULTI/CH control to access Menu No 01.
2 Press [M.IN]/ [SCAN (SG.SEL)] to begin editing
the message.
3 Move the cursor to the left or right by pressing
[Q-M.IN] or [Q-MR].
4 Press [M.IN]/ [SCAN (SG.SEL)] or turn the MULTI/
CH control to select your desired character.
• You can delete the selected character by
pressing [CL].
5 Repeat steps 3 and 4 to enter the remaining
characters.
6 Press [MENU] to set the entry and exit character
entry mode.
• Press [CLR] at any time to cancel character
entry mode and exit the Menu mode.
Available alphanumeric characters:
A B C D E F G H I J K L M N O P Q(q) R S T U V W X
Y Z (space) + – / 0 1 2 3 4 5 6 7 8 9