Renault LAGUNA Handbook
  1. Manuals
  2. Brands
  3. Renault Manuals
  4. Automobile
  5. LAGUNA
  6. Handbook

Renault LAGUNA Handbook

Hide thumbs Also See for LAGUNA:
Table of Contents

Advertisement

Quick Links

See also: Handbook , Quick Manual
LAGUNA
DRIVER'S HANDBOOK

Advertisement

Table of Contents
loading

Related Manuals for Renault LAGUNA

Summary of Contents for Renault LAGUNA

  • Page 1 LAGUNA DRIVER’S HANDBOOK...
  • Page 2 RENAULT vehicles. ► ELF lubricants are a major factor in your vehicle’s performance. RENAULT recommends the approved ELF lubricants for your oil changes and top-ups. Contact your RENAULT representative or visit the site: www.lubricants.elf.com The oil born in Formula One...

  • Page 3: Driving

    Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle. Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from RENAULT, 92 100 Billancourt 2010.
  • Page 5 Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........

  • Page 7: Table Of Contents

    Section 1: Getting to know your vehicle RENAULT cards: general information, use, deadlocking ....... . .

  • Page 8: Doors

    (refer to the informa- They may pose a risk to themselves on the card. Refer to the information tion on the “RENAULT card: Battery” in or to others by starting the engine, on the “RENAULT SERVICE card” in Section 5).
  • Page 9 Avoid leaving the card in hot, cold or netic radiation zone. humid areas. Do not keep the RENAULT card in a place where it could be bent or dam- aged accidentally, such as in a back pocket of a garment.

  • Page 10: Filler Flap

    30 seconds when button 3 RENAULT card is still in the reader, is pressed. the doors and luggage compartment Note: pressing button 3 again switches lock then quickly unlock and the hazard off the lighting.

  • Page 11: Unlocking The Vehicle

    With the RENAULT card in zone 1, the functions of the remote control place your hand on a door handle 2: the RENAULT card, it can be used to lock vehicle will unlock (in some cases, you and unlock without using the RENAULT may need to pull door handle 2 twice to card, when it is in access zone 1.

  • Page 12: Locking The Vehicle

    The vehicle will lock. If a door or the tailgate is open or not closed properly, the vehicle will quickly lock/ unlock. Note: the RENAULT card must be within the vehicle’s access zone (zone 1) to be able to use the button for locking. special note:...
  • Page 13 RENAULT cARd IN “hANds-fREE” mOdE: use (continued) With the engine running, if, after having opened and closed a door, the card is no longer in the passenger com- partment, the message “card not de- tected” (accompanied by a beep when...
  • Page 14 RENAULT cARd: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. The hazard warning lights flash once to indicate that the doors have been un- locked. To activate deadlocking If the vehicle is equipped with a dead-...
  • Page 15 RENAULT “sERvIcE” cARd deactivation of the “service” mode There are two possibilities: – Press a button on a RENAULT card (not the RENAULT “service” card); – start the engine with a RENAULT card (not the RENAULT “SERVICE” card). With the card in reader 3, press button 4.
  • Page 16 Pull on the handle 2. With the doors unlocked or “hands-free” Note: the lights and accessories (radio RENAULT card on you, hold handle 1 etc.) continue to work after the engine and pull it towards you. is switched off. They stop as soon as the driver’s door is opened.

  • Page 17: Child Safety

    OpENINg ANd cLOsINg ThE dOORs (continued) safety of rear occupants The driver can authorise operation of the rear doors and, depending on the ve- hicle, the electric windows by press- ing switch 1 on the side with the il- lustration. Depending on the vehicle, in the event of a fault: –...

  • Page 18: Locking/Unlocking Doors

    “RENAULT card” in Section 1. In certain cases, the RENAULT card may not work: – if the RENAULT card battery is weak, flat, etc. – if equipment operating on the same frequency as the card (mobile phones, etc.) is used;...
  • Page 19 When you lock the doors, the indicator The vehicle can only be unlocked from light remains lit and then goes out. outside when the RENAULT card is in the vehicle's access zone. Interior locking/unlocking door control...

  • Page 20: Automatic Locking When Driving

    AUTOmATIc LOckINg WhEN dRIvINg Activating/deactivating the Operating faults function If you experience an operating fault (no automatic locking, the indicator light in- Refer to the information on the “Vehicle corporated in button 1 does not light up settings personalisation menu” in when trying to lock the doors and tail- Section 1;...

  • Page 21: Front Headrests

    fRONT hEAdREsTs To adjust the angle of the headrest Depending on the vehicle, tilt section A towards or away from you to the re- quired position. To remove the headrest Raise the headrest to its highest po- sition (tilt the seatback backwards if necessary).

  • Page 22: Heated Seats

    fRONT sEATs WITh mANUAL cONTROL To move the seat forwards or To raise or lower the seat back base Lift handle 1 to release. Release the Move lever 3 as many times as neces- handle at the desired position and make sary upwards or downwards.

  • Page 23: Adjusting The Lumbar Support

    fRONT sEATs WITh ELEcTRIc cONTROL Switch 3 is used for adjusting the seat- back and switch 4 is used for adjusting the seat squab. On equipped vehicles, buttons 2 are used to store the chosen driving posi- tion (refer to the following page). Adjusting the seat squab: –...
  • Page 24 – with the “hands-free” card de- tected or, depending on the vehicle, RENAULT card in the card reader; – when the driver’s door is opened. storing your driving position Adjust the seat using switches 4 and 5 (see previous page).

  • Page 25: Seat Belts

    sEAT BELTs Before starting, adjust your driving Always wear your seat belt when trav- elling in your vehicle. You must also position and then have each occu- comply with the legislation of the par- pant adjust their seat belt to ensure ticular country you are in.
  • Page 26 sEAT BELTs (continued) ç front seat belt reminder warning light This comes on when the engine is started, then, if the driver’s or front passenger’s seat belt is not fastened (if this seat is occupied) and the vehi- cle has reached approximately 12 mph (20 km/h), it flashes and a bleep sounds for around 2 minutes.
  • Page 27 sEAT BELTs (continued) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. – For special operations (e.g.: fitting child seats) contact an approved Dealer. –...

  • Page 28: To The Front Seat Belts

    mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- – lap belt pretensioners; ever is permitted on any part of the system (pretensioners, air –...

  • Page 29: Methods Of Restraint In Addition To The Front Seat Belts

    mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (continued) Load limiter Air bags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at Depending on the vehicle, the pres- an acceptable level.
  • Page 30 mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (continued) Operation special feature of the front air This system is only operational when the ignition is switched on. After a violent impact, it has two deploy- ment volumes and integrates a ventila- In a severe frontal impact, the air bags tion system: inflate rapidly, cushioning the impact...
  • Page 31 mEThOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (continued) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...

  • Page 32: To The Rear Seat Belts

    mEThOds Of REsTRAINT IN AddITION TO ThE REAR sEAT BELTs force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...

  • Page 33: Side Protection Devices

    sIdE pROTEcTION dEvIcEs side air bags An air bag is fitted to each front seat and, depending on the country, the rear side seats; these air bags are deployed on the side of the seat (door side) to protect the occupants in the event of a severe side impact.
  • Page 34 AddITIONAL mEThOds Of REsTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.

  • Page 35: Child Safety: General Information

    chILd sAfETy: general information carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- ished growing.

  • Page 36: Child Safety: General Information

    chILd sAfETy: general information (continued) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
  • Page 37 chILd sAfETy: choosing a child seat Rear-facing child seats forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need From 15 kg or 4 years, the child can than that of an adult and its neck is very to be protected as a priority.

  • Page 38: Choosing A Child Seat Mounting

    chILd sAfETy: choosing a child seat mounting The are two ways of attaching child Attachment with the IsOfIX system Do not use the child seat seats: via the seat belt or using the Authorised ISOFIX child seats are ap- if it may unfasten the seat ISOFIX system.
  • Page 39 chILd sAfETy: choosing a child seat mounting (continued) The two rings 1 are located between The third ring is used to attach the the seatback and the seat base of the upper strap on some child seats. seat and are identified by a marking. Fix the hook of the strap onto ring 3 and To ensure your child seat can be easily pull the strap so that the seatback of the...
  • Page 40 chILd sAfETy: fitting a child seat In the front seat In the rear side seat Some seats are not suitable for fitting child seats. The diagram on the follow- The laws concerning children travel- A carrycot can be installed across the ing page shows you how to attach a ling in the front passenger seat differ in vehicle and will take up at least two...
  • Page 41 chILd sAfETy: fitting a child seat (continued) child seat attached using the IsOfIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
  • Page 42 chILd sAfETy: fitting a child seat (continued) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. seat size Weight of front passenger Rear centre Type of child seat Rear side seats the child seat (1) (5)

  • Page 43: Deactivating/Activating The Front Passenger Air Bag

    chILd sAfETy: deactivating/activating the front passenger air bag deactivating the front To deactivate the air bag: when the vehicle is stationary, push and turn passenger air bag lock 1 to the Off position. (on equipped vehicles) With the ignition on, you must check You must deactivate the front passen- ger air bag before fitting a child seat on that indicator light 2...
  • Page 44 chILd sAfETy: deactivating/activating the front passenger air bag (continued) The markings on the dashboard and la- bels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. dANgER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEvER...

  • Page 45: Passenger Air Bag

    chILd sAfETy: deactivating/activating the front passenger air bag (continued) dANgER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEvER fit a rear-facing child seat on a front passenger seat with an active front air bag.

  • Page 46: Driving Position

    dRIvINg pOsITION LEfT-hANd dRIvE 11 12 22 21 1.40...
  • Page 47 – front fog lights, 22 Engine start/stop button 11 Side window demister outlet. – rear fog light. RENAULT card reader. 12 Side air vent. 4 Instrument panel. 23 Control for adjusting steering wheel 13 Glove box. height and reach. 5 Driver’s air bag and horn location.
  • Page 48 dRIvINg pOsITION, RIghT-hANd dRIvE 11 12 1.42...
  • Page 49 – front fog lights, 15 Control for adjusting steering wheel – rear fog light. height and reach. 8 Instrument panel. 16 Engine start/stop control and RENAULT card reader. 9 Location for driver’s air bag and horn. 17 Central door locking/unlocking con- trols. 1.43...

  • Page 50: Steering Wheel

    sTEERINg WhEEL/pOWER-AssIsTEd sTEERINg variable power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) whilst the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
  • Page 51 INsTRUmENT pANEL: warning light The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRy. á main beam headlight tell-tale Electronic parking brake light and brake circuit fault warn- ing light dipped beam headlight tell- tale light If it comes on during braking and is ac- ®...
  • Page 52 INsTRUmENT pANEL: warning lights (continued) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRy. Ä sTOp light Toxic fume filter system ® Warning Light This lights up when the ignition is switched on and goes out as soon as This lights up when the ignition is the engine is started.
  • Page 53 INsTRUmENT pANEL: warning lights (continued) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRy. ç ã front seat belt reminder passenger air bag Off warning light Refer to the information on “Child This comes on when starting the engine safety”...
  • Page 54 INsTRUmENT pANEL: warning lights (continued) The presence and operation of the warning lights dEpENd ON ThE EQUIpmENT ANd cOUNTRy. The following warning lights are indicated on the trip computer and warning system screen: ù driving correction device warning light Refer to the information on “Driving cor- rection devices”...
  • Page 55 INsTRUmENT pANEL: displays and indicators coolant temperature indicator 6 In normal use, the needle should be before area a. Under severe condi- tions, the needle may enter this area. ® This is not serious unless the warning light comes on, accompanied by a message on the instrument panel and a beep.

  • Page 56: Trip Computer And Warning System

    TRIp cOmpUTER ANd WARNINg sysTEm c) mileage before service; d) tyre pressure monitor; e) cruise control/speed limiter pro- grammed speed; f) vehicle settings customisation menu; g) on-board log, operating fault and in- formation message readout. Trip computer and warning display selection keys 2 system 1 and 3 Depending on the vehicle, this includes...
  • Page 57 TRIp cOmpUTER ANd WARNINg sysTEm (continued) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
  • Page 58 TRIp cOmpUTER ANd WARNINg sysTEm (continued) The display of information shown below dEpENds ON ThE vEhIcLE EQUIpmENT ANd cOUNTRy. Examples of selections Interpreting the display selected a) Total mileage and trip mileage recorder. b) Journey parameters. fuel used. Fuel consumed since the last reset. Average fuel consumption since the last reset.
  • Page 59 TRIp cOmpUTER ANd WARNINg sysTEm (continued) The display of information shown below dEpENds ON ThE vEhIcLE EQUIpmENT ANd cOUNTRy. Examples of selections Interpreting the display selected current fuel consumption. This value is displayed above a speed of approximately 18 mph (30 km/h). Estimated range with remaining fuel.
  • Page 60 TRIp cOmpUTER ANd WARNINg sysTEm (continued) The display of information shown below dEpENds ON ThE vEhIcLE EQUIpmENT ANd cOUNTRy. Examples of selections Interpreting the display selected c) mileage before service. Distance remaining until the next service (displayed in miles (kilometres) and months), then when the service nears, several scenarios are possible: –...
  • Page 61 TRIp cOmpUTER ANd WARNINg sysTEm (continued) Journey parameters The display of information shown below dEpENds ON ThE vEhIcLE EQUIpmENT ANd cOUNTRy. Examples of selections Interpreting the display selected d) Tyre pressure monitor Refer to the information on the “Tyre pressure monitor” in Section 2. e) cruise control/speed limiter programmed speed.
  • Page 62 TRIp cOmpUTER ANd WARNINg sysTEm (continued) Journey parameters (continued) The display of information shown below dEpENds ON ThE vEhIcLE EQUIpmENT ANd cOUNTRy. Examples of selections Interpreting the display selected f) vehicle settings customisation menu. Enables certain vehicle functions to be set (instrument panel language, parking distance control, etc.).

  • Page 63: Information Messages

    “Remove card” Request to remove the RENAULT card from the reader when you leave the vehicle. “Test of functions Displayed with the ignition on when the vehicle is running self-diagnostics.
  • Page 64 TRIp cOmpUTER ANd WARNINg sysTEm (continued) Operating fault messages © These appear with the warning light and mean that you should drive very carefully to an approved dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. ©...

  • Page 65: Warning Messages

    TRIp cOmpUTER ANd WARNINg sysTEm (continued) Warning messages ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. stop your engine and do not restart it. contact an approved dealer. Examples of warning messages are given in the following pages.

  • Page 66: Vehicle Settings Customisation Menu

    vEhIcLE sETTINgs cUsTOmIsATION mENU Once a line has been selected, keep pressing either button 2 or 3 to change the function: For the “parking distance control volume” or “language” functions, you will have to make a further selection. In this case, make your selection and con- firm it by holding either button 2 or 3, the value selected is shown by a in front of the line.

  • Page 67: Clock And Exterior Temperature

    cLOck ANd EXTERIOR TEmpERATURE vehicles equipped with a External temperature navigation system, radio, etc. indicator For vehicles which are not fitted with special note: buttons 2 and 3, refer to the specific When the outside temperature is –3°C equipment instructions to discover the to +3°C, the °C characters flash (signal- special features.

  • Page 68: Door Mirrors

    REAR vIEW mIRRORs storing the setting For vehicles fitted with a driver’s seat with position memorisation, refer to the information on the “driver’s seat with position memory” in Section 1. folding door mirrors The door mirrors automatically fold in when the vehicle is locked (switch 2 in position B).

  • Page 69: Interior Rear View Mirror

    REAR vIEW mIRRORs (continued) Recalling the memorised position With the vehicle stationary and re- verse gear engaged, select the door mirror using switch 3 and then briefly press the memory button chosen pre- viously (refer to the information on the “Driver’s seat with position memory”...

  • Page 70: Audible And Visual Signals

    AUdIBLE ANd vIsUAL sIgNALs direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0.

  • Page 71: Exterior Lighting And Signals

    EXTERIOR LIghTINg ANd sIgNALs daytime running lights function (only relates to front lights) Depending on the vehicle, the lights come on without using stalk 1 when the engine is started. To activate or deacti- vate this function, refer to the informa- tion on the “Vehicle settings personali- sation menu”...

  • Page 72: Switching Off The Lights

    EXTERIOR LIghTINg ANd sIgNALs (continued) special note: “see-me-home lighting” – If the dipped beam headlights are function manually switched on and if the light This function allows you to briefly switch is sufficient, the directional head- on the dipped beam headlights (to pro- lights will remain fixed;...

  • Page 73: Rear Fog Light

    EXTERIOR LIghTINg ANd sIgNALs (continued) front fog lights switching off the lights Turn centre ring 5 on stalk 1 Turn ring 5 again until mark 6 is oppo- until the symbol faces mark 6, then re- site the symbol for the fog light that you lease it.
  • Page 74 ELEcTRIcAL AdJUsTmENT Of ThE dIppEd BEAm hEAdLIghTs Examples of positions for adjusting control A according to the load saloon and Estate commercial vehicle driver alone or with front passenger driver with one front passenger and one rear passenger On vehicles fitted with this function, con- trol A allows you to adjust the height of the beams according to the load.

  • Page 75: Wash/Wipe

    WINdscREEN WAsh/WIpE vehicle fitted with front windscreen wiper rain sensor A park B automatic wiper function. When this position is selected, the system detects water on the wind- screen and triggers the wipers at a suitable wiping speed. It is possi- ble to change the triggering thresh- old and the time sweeps by turning ring 2:...

  • Page 76: Headlight Washers

    WINdscREEN WAsh/WIpE (continued) headlight washers headlights on On equipped vehicles, hold stalk 1 pulled towards you for about 1 second, and the headlight washers and wind- screen washers will be activated at the same time. Note: when the minimum windscreen washer fluid level is reached, the head- light washer system may be deprimed.

  • Page 77: Rear Screen Wiper

    REAR scREEN WAsh/WIpE Activation/deactivation of the rear screen wiper Your vehicle is designed to activate the rear wiping function in reverse gear (if the windscreen wipers are operating). You can choose to activate or deacti- vate the function. To do this, refer to the information on the “Vehicle set- tings customisation menu”...

  • Page 78: Fuel Tank (Filling With Fuel)

    fUEL TANk fuel grade Always use a high-grade fuel that complies with legislation in force in each country and conforms to the spec- ifications given on label C. Refer to the information on “Engine specifications” in Section 6. diesel versions It is essential to use diesel fuel that conforms to the information given on the label inside cover C.
  • Page 79 fUEL TANk (continued) filling with fuel vehicles running on ethanol-based fuel Insert the nozzle to open valve B and It is essential to use unleaded petrol or insert it fully before turning it on to fill fuel containing a maximum of 85% eth- the fuel tank (risk of splashing).
  • Page 80 fUEL TANk (continued) persistent smell of fuel If you notice a persistent smell of fuel you should: – stop the vehicle as soon as traf- fic conditions allow and switch off the ignition; – switch on the hazard warning lights and ask your passengers to leave the vehicle and to keep away from traffic;...
  • Page 81 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Starting - stopping the engine .

  • Page 82: Running In

    RUNNING IN Petrol version Diesel version Up to 600 miles (1,000 km), do not For the first 900 miles (1,500 km), do exceed 78 mph (130 km/h) in top gear not exceed 2,500 rpm. After complet- or 3,000 to 3,500 rpm. ing this mileage you may drive faster, however, it is only after approximately You may only expect top performance...

  • Page 83: Starting/Stopping The Engine

    “turn steering wheel + start” Starting the engine RENaULt card in hands-free mode warns of this. The RENAULT card must be inserted in Remote control RENaULt card Starting with the tailgate open (in card reader 2 or in detection zone 3.
  • Page 84 (continued) Operating faults In certain cases, the hands-free RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc. – near to appliances operating on the same frequency as the card (monitor, mobile phone, video game, etc.);...
  • Page 85 If the card is no longer in the reader cle, especially if you have when you try to switch the engine off, your RENAULT card with the message “card absent- long press” you, check that the engine appears on the instrument panel: press is completely switched off.

  • Page 86: Special Features Of Petrol Versions

    SPECIaL FEatURES OF PEtROL vERSIONS The following operating conditions If you notice any of the above operating should be avoided: faults, have the necessary repairs car- ried out as soon as possible by an ap- – driving for long periods when the low proved dealer.

  • Page 87: Special Features Of Diesel Versions

    SPECIaL FEatURES OF DIESEL vERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.

  • Page 88: Gear Lever

    GEaR LEvER/HaNDbRakE Handbrake The reversing lights will come on as soon as reverse gear is selected with the ignition on. to release: Pull lever 3 up slightly, press button 2 and then lower the lever to the floor. to apply: Pull upwards, check that the vehicle is properly immobilised.

  • Page 89: Automatic Operation

    aSSIStED PaRkING bRakE Note: The message “apply parking brake” ap- pears on the instrument panel and a beep sounds to indicate that the elec- tronic parking brake is applied or re- leased: This message may appear: – with the engine running: when the driver’s door is opened;...

  • Page 90: Manual Operation

    3 at the same time; You can control the electronic parking To manually activate the electronic park- – remove the RENAULT card from the brake manually. ing brake, (when stopping at a red light, reader. or stopping when the engine is running, applying the electronic parking etc.): pull and release switch 3.
  • Page 91 aSSIStED PaRkING bRakE (continued) versions with an automatic Operating faults – If there is an electronic parking brake ® fault, the warning lights illu- gearbox © – If there is a fault, the warning minate accompanied by the “Parking light illuminates on the instrument For safety reasons, automatic release brake fault”...

  • Page 92: Engine Adjustments

    aDvICE: antipollution, fuel economy, driving aiding fuel economy By virtue of its design, moderate fuel Have your vehicle adjusted and checked consumption and initial settings, your by an approved Dealer, in accordance Depending on the vehicle, in order to vehicle conforms to current antipol- with the instructions given in your main- optimise consumption, an indicator light lution regulations.
  • Page 93 aDvICE: antipollution, fuel economy, driving (continued) Exhaust gas monitoring – Brake as little as possible. If you an- ticipate an obstacle or bend in ad- system vance, you may then simply release The exhaust gas monitoring system will the accelerator pedal. detect any operating faults in the vehi- –...
  • Page 94 aDvICE: antipollution, fuel economy, driving (continued) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.

  • Page 95: Environment

    This commitment is illustrated by the less fuel (eg. 140 g/km, equivalent to the vehicle components have been de- Renault eco² group signature. 5.3 l/100 km for a diesel vehicle). signed to enable them to be recycled. Our vehicles are also equipped with a...

  • Page 96: Tyre Pressure Monitor

    tyRE PRESSURE MONItOR the tyre pressure can be adjusted If the vehicle is equipped with the func- tion, this system monitors the tyre pres- when cold (refer to the information on sure. “Tyre pressures”). If tyre pressures cannot be checked when the tyres are cold, the recom- Operating principle mended pressures must be increased...
  • Page 97 tyRE PRESSURE MONItOR (continued) “Check tyre pressure” A shaded wheel B indicates a deflated tyre. “Inflate tyres to motorway pressure” The tyre pressure is not suitable for the speed of travel. Slow down or inflate all four tyres to motorway pressure (refer to the information on “Tyre pressures”).
  • Page 98 tyRE PRESSURE MONItOR ( continued Emergency spare wheel If the vehicle is equipped with an emer- gency spare wheel, it will not have a sensor. When it is fitted to the vehicle, the message “tyre sensors absent” is displayed on the instrument panel. Replacing wheels/tyres This system requires specific equip- ment (wheels, tyres, hubcaps, etc.).

  • Page 99: Driver Correction Devices/Aids

    DRIvER CORRECtION DEvICES aND aIDS abS (anti-lock braking Operating faults: Depending on the vehicle, they may comprise: system) © – the (anti-lock braking – lit on the in- Under heavy braking, the ABS prevents system); strument panel accompanied by the wheels from locking, allowing the –...

  • Page 100: Electronic Stability Program

    DRIvER CORRECtION DEvICES aND aIDS (continued) Electronic stability program Understeer control Operating faults (ESP) with understeer control This system optimises the action of the When the system detects an operating and traction control (aSR) ESP in the case of pronounced unders- fault the message “Check ESP”...

  • Page 101: Emergency Brake Assist

    DRIvER CORRECtION DEvICES aND aIDS (continued) Hazard warning lights switching on Traction control (ASR) offers additional safety; it is recommended that you do Depending on the vehicle, these may not drive with the function disabled. light up in the event of sudden decel- Correct this as soon as possible by eration.
  • Page 102 DRIvER CORRECtION DEvICES aND aIDS (continued) Operating faults © – If the indicator light together with the message “check steering” is displayed on the instrument panel: consult an approved Dealer. ® – if the indicator light gether with the message “steering fault”...
  • Page 103 DRIvER CORRECtION DEvICES aND aIDS (continued) Hill start assistance This function assists the driver when starting on hills. It prevents the vehicle from rolling backwards, depending on the slope, by automatically applying the The hill start assistance brakes when the driver lifts his/her foot system cannot completely off the brake pedal to depress the ac- prevent the vehicle from...
  • Page 104 CRUISE CONtROL - SPEED LIMItER: limiter function Controls Switching on The speed limiter function helps you stay within the driving speed limit that  1 Main “On/Off” switch. Press switch 1 on the side showing you choose, known as the limit speed. Indicator light 6 comes on, lit orange, 2 Limit speed activation, storage and and the message “speed limiter”...

  • Page 105: Speed Limiter

    CRUISE CONtROL - SPEED LIMItER: limiter function (continued) varying the limit speed Limited speed cannot be maintained When driving down a steep gradient, To vary the limit speed, press the system is unable to maintain the switch 2 (+) repeatedly to increase the limit speed: the stored speed will flash speed or switch 3 (-) to decrease.
  • Page 106 CRUISE CONtROL - SPEED LIMItER: limiter function (continued) Recalling the limit speed If a speed has been stored, it can be re- called by pressing switch 5 (R). Putting the function on Switching off the function standby The speed limiter function is deac- tivated if you press switch 1: in this The speed limiter function is suspended case a speed is no longer stored.
  • Page 107 CRUISE CONtROL - SPEED LIMItER: cruise control function This function is an addi- tional driving aid. However, the function does not take the place of the driver. Controls The cruise control function helps you to Therefore, it can under no circum- maintain your driving speed at a speed stances replace the driver’s respon- that you choose, called the cruising...
  • Page 108 CRUISE CONtROL - SPEED LIMItER: cruise control function (continued) Switching on activating cruise control Driving Press switch 1 on the side showing At a steady speed (above 20 mph Once a cruising speed is stored and  (30 km/ h) approximately) press switch 2 the cruise control function is active, (+) or 3 (-): the function is activated and you may lift your foot off the accelera-...
  • Page 109 CRUISE CONtROL - SPEED LIMItER: cruise control function (continued) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel.
  • Page 110 CRUISE CONtROL - SPEED LIMItER: cruise control function (continued) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road condi- tions are suitable (traffic, road surface, weather conditions, etc.). With a vehicle speed above 20 mph (30 km/h), press switch 5 (R).

  • Page 111: Parking Distance Control

    PaRkING DIStaNCE CONtROL Operating principle Ultrasonic detectors, installed in the front or rear bumper depending on the vehicle, measure the distance between the vehicle and an obstacle whilst re- versing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 25 centi-...
  • Page 112 PaRkING DIStaNCE CONtROL (continued) automatic activation/deactivation of the front parking distance control The system deactivates: – when the assisted parking brake is applied; – when the vehicle speed is above ap- proximately 6 mph (10 km/h); – when the vehicle is stationary for more than approximately five sec- onds (such as when in a traffic jam or waiting at red lights, etc.);...

  • Page 113: Special Features

    PaRkING DIStaNCE CONtROL (continued) Prolonged deactivation of the Special features system Make sure that the ultrasonic sensors are not obscured (by dirt, mud, snow, You may permanently activate or deac- etc.). tivate the front or rear parking distance control separately. Operating faults From the vehicle settings customisation menu (refer to the information on the...

  • Page 114: Automatic Gearbox

    aUtOMatIC GEaRbOx Driving in automatic mode Select position D. In most traffic con- ditions, you will not have to touch the gear selector lever again: the gears will change automatically at the right time and at the most suitable engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particu-...

  • Page 115: Parking The Vehicle

    aUtOMatIC GEaRbOx (continued) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, – If the road contours and bends When the vehicle is stopped, move the move the lever to the left. Shifting the do not allow you to stay in auto- lever to position P while keeping your lever repeatedly allows you to change...
  • Page 116 aUtOMatIC GEaRbOx (continued) Operating faults – When driving, if the message “Check gearbox” together with the © warning light appears on the instrument panel, this indicates a fault. Contact your approved Dealer as soon as possible. – When driving, if the message “Gearbox overheating”...

  • Page 117: Your Comfort

    Section 3: Your comfort Air vents............... Manual air conditioning/heating system .

  • Page 118: Air Vents

    AIR VENTS, air outlets 1 left-hand side window demister outlet 2 left-hand side air vent 6 right-hand side window demister 3 windscreen demister outlets outlet 7 right-hand side air vent 4 dashboard upper air vent 8 passenger footwell heater outlets 5 air conditioning control panel 9 centre air vents 10 rear passenger air vents...

  • Page 119: Air Flow

    AIR VENTS, air outlets (continued) Air flow Direction To remove bad odours from your ve- hicles, only use the systems designed Move the control knob 1 (beyond the Right/left: move tabs 2 to the right or for this purpose. Consult an approved point of resistance).

  • Page 120: Manual Air Conditioning/Heating System

    MANuAl AIR coNDITIoNINg/hEATINg SySTEM Switching air conditioning on The arrows located in area a on dis- play 3 combine to show you the distri- or off bution selected: The air conditioning is switched on (in- § dicator light illuminated) or off (indicator The air flow is directed to- light extinguished) using button 1.

  • Page 121: Adjusting The Ventilation Speed

    MANuAl AIR coNDITIoNINg/hEATINg SySTEM (continued) Position 0 (ventilation fan in zone b Switching the air empty) recirculation on the system is deactivated: the ventila- Press air recirculation button 8: the in- tion speed for the passenger compart- dicator light comes on. ment air is zero (vehicle stationary), you In these conditions air is taken from the can however still feel a slight flow of air...

  • Page 122: Automatic Climate Control

    AuToMATIc clIMATE coNTRol Automatic mode Temperature adjustment The automatic climate control system Press either button 1 or 5 to increase guarantees comfort in the passen- or decrease the temperature. Pressing ger compartment and good visibility button 3 for more than 2 seconds sets (except in the event of extreme condi- the passenger temperature to the driv- tions), whilst optimising consumption.
  • Page 123 AuToMATIc clIMATE coNTRol (continued) Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. Press button 10 to switch off the air conditioning. Where possible, it is recom- mended that automatic mode is The displayed temperature values Varying the ventilation speed...
  • Page 124 AuToMATIc clIMATE coNTRol (continued) „ clear View function the air flow is directed towards the dashboard air vents (posi- Press button 8, the integrated indica- tion which allows the passenger com- tor comes on and the indicator light for partment to be heated or cooled as button 3 goes out.

  • Page 125: Air Recirculation

    AuToMATIc clIMATE coNTRol (continued) Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; – air recirculation allows the external atmosphere to be cut off (when driv- ing in polluted areas, etc.).

  • Page 126: Maintenance

    AIR coNDITIoNINg: information and advice on use Advice on use In some situations, (air conditioning operating faults off, air recirculation activated, venti- Fuel consumption lation speed at zero or low, etc.) you As a general rule, contact your ap- You will normally notice an increase may notice that condensation starts proved Dealer in the event of an op- in fuel consumption (especially...

  • Page 127: Electric Windows/Electric Panoramic Sunroof

    Driver’s responsibility Never leave your vehicle with the Electric windows one-touch mode RENAULT card inside and never Depending on the vehicle, this mode is Press or pull the switch to raise or lower leave a child (or a pet) unsuper-...

  • Page 128: Special Note

    (some- body’s fingers, etc.) it stops and then moves back several centimetres. Driver’s responsibility Never leave your vehicle with the RENAULT card Sunroof blind Sunroof inside and never leave a Only ever operate the blind with the –...

  • Page 129: Precautions During Use

    Technical Department; necessary to fully close the window, RENAulT card twice in quick suc- then hold the switch (still on the closure – do not open the sunroof immedi- cession, or on the driver's door in...

  • Page 130: Sun Visor

    SuN VISoR Front sun visor Side sun blind Rear sun blind Lower the sun visor 1 over the wind- Pull the sun visor upwards using tab 3 Pull the sun visor upwards using tab 5 screen or unclip it and turn it over the until hooks 4 engage in their hous- until hooks 6 engage in their hous- side window.

  • Page 131: Interior Lighting

    INTERIoR lIghTINg courtesy light Front door lights glove box light 5 Tilt switch 2 to move it to the position Light 4 comes on when the door is Light 5 comes on when the cover is for: opened. opened. – permanent lighting; –...
  • Page 132 INTERIoR lIghTINg (continued) Floor lights 6 luggage compartment lights 7 or 8 Floor light 6 comes on when a door is opened. Depending on the vehicle, light 7 or 8 comes on when the luggage compart- ment is opened. 3.16...

  • Page 133: Passenger Compartment Storage Space And Fittings

    PASSENgER coMPARTMENT SToRAgE SPAcE AND FITTINgS Door pockets 1 Dashboard storage compartment 2 Ensure that no hard, heavy Nothing should be placed or pointed objects are on the floor area in front of placed in the “open” stor- the driver as such objects age compartments in such may slide under the pedal a way that they may fall onto pas-...

  • Page 134: Glove Box

    PASSENgER coMPARTMENT SToRAgE SPAcE AND FITTINgS (continued) Sun visor storage 3 Front centre armrest storage glove box compartment A This can be used for storing motorway Pull handle 6 to open it. tickets, cards, etc. Press button 4 and lift cover 5. The glove box can hold A4-sized docu- ments, a large bottle of water, etc.
  • Page 135 PASSENgER coMPARTMENT SToRAgE SPAcE AND FITTINgS (continued) cup holder 7 Door pockets 8 Rear armrest storage This can be used to hold a can or a Lower armrest 11 and lift cover 10 using cup. unlocking handle 9. Press the top to deploy or store it. When turning corners, accelerating or braking, ensure that the recepta-...
  • Page 136 PASSENgER coMPARTMENT SToRAgE SPAcE AND FITTINgS (continued) clothes hooks 12 Front seat storage compartments 14 grab handle 13 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle.

  • Page 137: Ashtray/Cigar Lighter

    AShTRAy/cIgAR lIghTER/AccESSoRIES SockET Ashtray 4 or 7 cigar lighter 2 Press on cover 1 or pull cover 7 to open With the ignition on, push in the cigar it. To empty it, pull divider 3, lifting the lighter; it will spring back with a click rear of the ashtray, or pressing tab 6.

  • Page 138: Rear Headrests

    REAR hEADRESTS Position for use To refit the headrest Raise or lower the headrest while pull- Insert the headrest rods into the ing it towards the front of the vehicle. sleeves, and lower the headrest to the first notch. To remove the headrest Storage position Press tab 1 and 2 simultaneously remove the headrest.

  • Page 139: Rear Bench Seat

    REAR BENch SEAT Sport tourer versions The seatbacks can be folded down in When refitting the seat- order to transport large objects. back, make sure it is cor- Press button 2 or pull handle 3: the In all situations, lower the rear head- rectly locked in place.

  • Page 140: Inside The Vehicle

    TAIlgATE Saloon version Sport tourer versions opening manually from To open inside the vehicle To open Press button 2 and lift the tailgate. Press button 1 and lift the tailgate. Special note: To close Lower the tailgate using the handles 3 If it is impossible to unlock the tailgate, To close inside the tailgate to help you.

  • Page 141: Opening Rear Screen

    oPENINg REAR ScREEN Vehicle with opening rear To close Driving with the rear screen screen Hold the base of screen wiper 1 and open may be unpleasant fold back the rear screen until it locks for passengers as exhaust The rear screen is locked and unlocked in position.

  • Page 142: Rear Parcel Shelf

    REAR PARcEl ShElF Removal Lift rear parcel shelf 2 slightly and pull it towards you. Unhook the two cords 1 (tailgate side). To refit it, proceed in reverse order to removal. Do not place any objects, especially heavy or hard objects, on the parcel shelf.

  • Page 143: Luggage Compartment Cover

    luggAgE coMPARTMENT coVER To remove the flexible section 1 of Removing the luggage cover 2 luggage compartment cover the luggage cover 2 storage 2 Slide button 3 and lift the right-hand Press on the rear of the luggage com- side (movement B) of the roller at the Lift up the rear of luggage compartment partment cover (movement A): the lug- same time.

  • Page 144: Luggage Compartment Storage Space And Fittings

    luggAgE coMPARTMENT SToRAgE SPAcE AND FITTINgS Saloon version Storage under carpet 2 Fold back section A to open it. Side storage compartments Located on each side of the luggage compartment, storage compartments 1 may be used to store oil containers, etc.
  • Page 145 luggAgE coMPARTMENT SToRAgE SPAcE AND FITTINgS (continued) Sport tourer versions hook for holding bags whilst Anchorage points cornering Hooks 6 located on each corner of the Separating the luggage Prevents bags moving when the vehi- luggage compartment, allow the load to compartment cle goes around a corner.

  • Page 146: Transporting Objects In The Luggage Compartment/Towing (Towing Equipment)

    TRANSPoRTINg oBjEcTS IN ThE luggAgE coMPARTMENT/ToWINg (towing equipment) C = 1000 mm Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. In all cases, take care to comply with local laws (e.g. remove the towing ball when not towing).

  • Page 147: Luggage Net

    luggAgE NET Refitting the luggage net With the rear bench seatbacks 1 com- pletely folded down, find the roller. From the right-hand rear door, slide roller 2 on the rails 3 located on the back of the large section of the rear bench seatback: ensure it is correctly locked by moving it back and forth gently, then lock the rear bench seat-...
  • Page 148 luggAgE NET (continued) Positioning the luggage net Remove rod 5 from its housing and insert it into the anchorage points 6 Behind the rear seats (it must be inserted in ring 7). From the rear seats, lift covers 4 to Fold up the seatbacks and lock them.
  • Page 149 luggAgE NET (continued) Note: when the luggage net roller is in- stalled on the back of the large section of the seatback, a system ensures the seatback does not fold down uninten- tionally. It is therefore necessary, after unlocking the seatback, to tilt it by pull- ing from the top beyond the point of re- sistance, from the right-hand rear door side.

  • Page 150: Navigation System

    MulTIMEDIA EquIPMENT Navigation system The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle navigation system version. 1 Radio; 2 Central control; 3 CD or DVD reader; 4 Microphone; 5 Steering column controls.
  • Page 151 Section 4: Maintenance Bonnet ............... . Engine oil level: .

  • Page 152: Bonnet

    BOnnet Opening the bonnet Closing the bonnet To open, pull handle 1, located on the left-hand side of the dashboard. Lift the bonnet and release stay 4 from Check that nothing has been left in the its holder 5. For your own safety, it is engine compartment.
  • Page 153 enGIne OIL LeVeL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period.

  • Page 154: Engine Oil Level

    enGIne OIL LeVeL: general information (continued) Once the operation has been completed, ensure that the dipstick is pushed in as far as it will go or that the “cap-type dip- stick” is completely screwed in. exceeding the maximum engine oil level The oil level should only be read with the dipstick as explained above.

  • Page 155: Topping Up/Filling

    enGIne OIL LeVeL: topping up/filling 1.6 16V 2.0 16V 2.0T topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
  • Page 156 enGIne OIL LeVeL: topping up/filling (continued) 1.5 dCi 2.0 dCi V6 dCi topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is...

  • Page 157: Oil Change

    enGIne OIL LeVeL: topping up/filling , enGIne OIL CHAnGe (continued) Oil change Service interval: refer Maintenance Service Booklet for your vehicle. Average capacities for oil change Filling: take care when including oil filter topping up the oil that (for information) no oil drips onto engine 1.6 16V engine : 5.0 litres components - risk of fire.

  • Page 158: Levels

    LeVeLS Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Service (very severe damage is likely to be Booklet for your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...

  • Page 159: Brake Fluid Level

    LeVeLS (continued) Level 1 topping up The level normally goes down at the After any operation on the hydraulic cir- same time as the brake lining wear, cuit, a specialist must replace the fluid. but it must never go below the « MINI » Only use fluids approved by our warning level.

  • Page 160: Windscreen/Headlight Washer Reservoir

    LeVeLS FILteRS (continued)/ Liquid Filters Screen wash product (product with an- The replacement of filter elements (air tifreeze in winter). filter, cabin filter, diesel fuel filter, etc.) is scheduled in the maintenance opera- Jets tions for your vehicle. Use a tool such as a needle to adjust Replacement intervals for filter el- the height of the windscreen washer ements: refer to the Maintenance...

  • Page 161: Tyre Pressure

    tyRe pReSSURe tyre safety and use of snow chains The tyre pressure is indicated on la- Zone D: tyre pressures for the rear bel A affixed to the edge of the driver’s wheels (non-motorway). Refer to the information on “Tyres” door.

  • Page 162: Battery

    BAtteRy Replacing the battery Depending on the vehicle, the battery is in the engine compartment or in the lug- As this operation is complex, we advise gage compartment. you to contact an approved Dealer. It is always maintenance-free. Depending on the vehicle, a system continuously checks the battery charge status.

  • Page 163: Bodywork Maintenance

    BODyWORk MAIntenAnCe (1/2) protection against the effects you should not: – Use solvents not approved by our Technical Department to remove of corrosive agents – Degrease or clean mechanical com- stains as this could damage the ponents (e.g. the engine compart- Although your vehicle has been treated paintwork.
  • Page 164 BODyWORk MAIntenAnCe (2/2) you should – Observe the vehicle stopping dis- – Before going through a roller type car tances when driving on gravelled wash, return the windscreen wiper – Wash your car frequently, with the surfaces to prevent paint damage. stalk to the Park position (refer to engine off, with cleaning products the information on the “Windscreen...

  • Page 165: Interior Trim Maintenance

    InteRIOR tRIM MAIntenAnCe – Seat belts What you should not do Whatever type of stain is on the trim, use soapy water (if possible, warm These must be kept clean. You are strongly advised not to place water) containing: items such as air fresheners, perfume Use products selected by our –...
  • Page 166 4.16...

  • Page 167: Practical Advice

    RENAULT card: battery ........

  • Page 168: Puncture

    Puncture/eMerGencY SPAre WHeeL In the event of a puncture, Special note: depending on the vehicle, The Tyre Pressure Monitor function you will have: does not check the emergency spare wheel (the wheel replaced by the emer- An emergency spare wheel or tyre in- gency spare wheel disappears from the flation kit (refer to the information on the instrument panel display).

  • Page 169: Tyre Inflation Kit

    tYre InFLAtIOn KIt Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
  • Page 170 tYre InFLAtIOn KIt (continued) If the recommended pressure cannot – Take the compressor 4 and the 4 5 6 bottle 1 located under the luggage be achieved, repair is impossible. Do compartment carpet; not drive the vehicle. consult an ap- proved dealer.
  • Page 171 tYre InFLAtIOn KIt (continued) Precautions when using the Start immediately and drive between 1.8 and 6 miles (3 and 10 km) (10 min- utes driving) then stop to check the The kit should not be operated for more pressure. If it is above 1.3 bar, adjust than 15 consecutive minutes.

  • Page 172: Wheel Trim

    tOOL KIt/WHeeL trIM - WHeeL Jack 1 Fold it and position retainer A correctly before refitting it in its housing. towing hitch 2 Refer to the information on “Towing” in Section 5. Hubcap tool 3 This tool is used to remove the wheel trims.

  • Page 173: Changing A Wheel

    cHAnGInG A WHeeL If necessary, remove the wheel trim. Start cranking the jack up by hand to align the base plate (which should be Use the wheelbrace 3 to slacken off the pushed slightly under the vehicle). wheel bolts. Position it so as to be able to push from above.
  • Page 174 cHAnGInG A WHeeL (continued) Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.

  • Page 175: Tyres (Tyre And Wheel Safety, Use In Winter)

    tYreS tyre and wheel safety When the tyre tread has been eroded to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.

  • Page 176: Tyre Pressures

    tYreS (continued) tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Adhere to the tyre pressures (including which may be reached in hot weather the emergency spare wheel). The tyre For safety reasons, this op- or following a fast journey.

  • Page 177: Changing Wheels Around

    tYreS (continued) changing wheels around use in winter This practice is not recommended. chains In all cases, we would recommend that you contact an approved dealer For safety reasons, fitting snow who will be able to advise you on chains to the rear axle is strictly for- the choice of equipment which is bidden.

  • Page 178: Headlights (Changing Bulbs)

    HALOGen HeADLIGHtS: changing bulbs Front side light Remove cover A, then pull bulb hold- er 6 to access the bulb. Bulb type: W5W. Direction indicator lights Consult an approved dealer. Dipped beam/main beam However, because the protective covers need to be removed, you are advised headlights to have your bulbs replaced by an Remove cover A or B then unclip...

  • Page 179: Daytime Running Light

    XenOn HeADLIGHtS: changing bulbs cleaning the headlights As the headlights are made of plastic glass, use a soft cloth or cotton wool to clean them. If this does not clean it properly, moisten the cloth with soapy water, then wipe clean with a soft damp cloth or cotton wool.
  • Page 180 HeADLIGHtS: additional/front fog lights Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved dealer. Front fog lights 1 Pull on cover 2 to access the bulb mounting; Unscrew the two bolts showing then turn the bulb towards the centre of the vehicle;...
  • Page 181 reAr LIGHtS AnD InDIcAtOr LIGHtS: changing bulbs Saloon version Undo bulb holder 3 a quarter of a turn. Replace bulb 4. Bulb type: W16W. Direction indicator lights From the luggage compartment, undo 2 a quarter of a turn to access bolt 1. Undo it then pull the light unit out- wards.

  • Page 182: Reversing Light

    reAr LIGHtS AnD InDIcAtOr LIGHtS: changing bulbs (continued) Saloon version (continued) Undo bolt 6 in order to remove light unit 7 by pushing it outwards. Undo bulb holder 8 a quarter of a turn reversing light then replace the bulb. From the luggage compartment, unclip Bulb type: W16W.
  • Page 183 reAr LIGHtS AnD InDIcAtOr LIGHtS: changing bulbs (continued) Sport tourer versions 11 Side lights/stop lights Bulb type: P21/5W. From the luggage compartment, remove the side carpet. 12 Direction indicator light note: depending on the vehicle, it may Bulb type: PY21W. be necessary to remove the door of storage compartment A.
  • Page 184 reAr LIGHtS AnD InDIcAtOr LIGHtS: changing bulbs (continued) Accessibility for vehicles From inside, undo the three bolts 16 then, from the outside, detach the light equipped with a speaker unit by pulling it back, and unclip the on the left of the luggage bulb holder.

  • Page 185: Indicator Lights (Changing Bulbs)

    reAr AnD SIDe LIGHtS: changing bulbs (continued) Saloon and sport tourer number plate lights 18 Indicator lights 20 versions Unclip light 18 by pressing tab 19. Unclip indicator light 20 (using a flatb- lade screwdriver type tool positioned Remove the light cover to gain access at B to move the indicator light towards High level brake light 17 to the bulb.

  • Page 186: Interior Lights: Changing Bulbs

    InterIOr LIGHtS: changing bulbs courtesy light Door lights Front floor lights Unclip the lens (using a flat-blade Unclip light 2 (using a flat-blade screw- These are located behind the dash- screwdriver or similar). driver or similar). board and on the lower section. Remove the bulb concerned 1.
  • Page 187 InterIOr LIGHtS: changing bulbs (continued) Luggage compartment lights Disconnect the light. Press tab 5 to release lens 7 and Unclip the light at 4 using a flat-blade access bulb 6. screwdriver or similar. Bulb type: W5W. The bulbs are under pres- sure and can break when replaced.

  • Page 188: Fuses

    FuSeS CORRECT INCORRECT Fuse box 2 clip 3 If any electrical component does not Remove the fuse using tweezers 3, lo- work, check the condition of the fuses. cated at the back of storage compart- ment A. Open storage compartment A. Press tab 1 to move it then pull it towards you To remove the fuse from the tweezers, to unclip it.
  • Page 189 FuSeS (continued) Allocation of fuses (DePenDInG On tHe eQuIPMent LeVeL) Symbol Allocation Symbol Allocation Ý Towing equipment supply Interior lighting  Radio amplifier  Interior rear-view mirror î Radio Heated rear screen Instrument panel Ì Horn  Child safety Driving correction devices Indicator ...

  • Page 190: Battery

    BAtterY: troubleshooting to avoid all risk of sparks: connecting a battery charger Starting the vehicle using the battery from another vehicle Do not place metal objects on the bat- the battery charger must be com- tery as this could create a short circuit patible with a battery with nominal If you have to use the battery from an- between the terminals.
  • Page 191 BAtterY: troubleshooting (continued) Starting the vehicle using the battery from another vehicle (continued) Ensure that there is no risk of contact between the two vehicles (risk of short circuiting when the positive terminals are connected) and that the discharged battery is properly connected. Switch off your vehicle ignition.

  • Page 192: Renault Card: Battery

    (insert the seal if it is not fully clipped on), then place the RENAULT card battery, press RENAULT card in the card reader) and press one of the card buttons, whilst in button 1 pulling on emergency key 2, lock/unlock the vehicle (refer to the in- the vicinity of the vehicle;...

  • Page 193: Fitting A Radio

    FIttInG A rADIO If your vehicle is not fitted with a radio, one can be fitted and locations have been provided for: – the radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please con- –...

  • Page 194: Accessories

    AcceSSOrIeS Before fitting an electrical or If you are using an anti-theft electronic device (particu- device, only attach it to the larly for transmitters/receiv- brake pedal. ers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle.

  • Page 195: Windscreen Wiper Blades

    WInDScreen WIPer BLADeS Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...

  • Page 196: Towing: Breakdown

    With the engine switched off, the trans- or r for vehicles with automatic trans- mission is no longer lubricated. It is missions), insert the RENAULT card in preferable to tow this type of vehicle on the card reader then press the engine a trailer or tow it with the front wheels start button for two seconds.
  • Page 197 Unclip strip 1 an insert key 2 built into by tightening it using the wheelbrace. for towing: never use them for lifting the the RENAULT card into the opening un- Towing hitch 4 and the wheelbrace are vehicle directly or indirectly.
  • Page 198 POSSIBLe cAuSeS WHAt tO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the information on “Locking/unlocking the...

  • Page 199: Operating Faults

    The engine will not start. Starting conditions are not fulfilled. Refer to the information on “Starting/stop- ping the engine” in Section 2. The hands-free RENAULT card Insert the card in the card reader in order to does not work. start the engine.
  • Page 200 OPerAtInG FAuLtS (continued) On the road POSSIBLe cAuSeS WHAt tO DO Vibrations. Tyres not inflated to correct pressures, Check the tyre pressures: if this is not the incorrectly balanced or damaged. problem, have them checked by an ap- proved dealer. Abnormal white smoke from the ex- Mechanical fault: cylinder head gasket Stop the engine.
  • Page 201 OPerAtInG FAuLtS (continued) On the road POSSIBLe cAuSeS WHAt tO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine overheats. The coolant Engine cooling fan not working. Stop the vehicle, switch off the engine and temperature indicator is in the warn- contact an approved dealer.
  • Page 202 OPerAtInG FAuLtS (continued) electrical equipment POSSIBLe cAuSeS WHAt tO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer.

  • Page 203: Technical Specifications

    Section 6: Technical specifications Vehicle identification plates ............Engine identification plates .

  • Page 204: Vehicle Identification Plates

    Vehicle identification plates the information shown on the ve- 6 Technical specifications of vehicle. hicle identification plate should be 7 Vehicle paint reference. quoted on all correspondence or 8 Equipment level. orders. 9 Vehicle type. 10 Trim code. Vehicle identification plate A 11 Additional equipment specifica- 1 Vehicle type and chassis number.

  • Page 205: Engine Identification Plates

    engine identification plates the information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
  • Page 206 engine identification plates (continued) the information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.

  • Page 207: Dimensions

    dimensions (in metres) 1.014 2.756 0.925 1.557 4.695 1.445* 1.512 2.060 Unladen...
  • Page 208 dimensions (in metres) (continued) 1.014 2.756 1.031 1.557 4.801 1.445* 1.512 2.060 Unladen...

  • Page 209: Engine Specifications

    engine specifications Versions 1.6 16V 2.0 16V 2.0t 1.5 dci 2.0 dci V6 dci engine type F4R Turbo (see engine plate) cubic capacity (cc) 1 598 1,995 1 998 1 461 1,995 2,993 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.

  • Page 210: Weights

    Weights (in kg) the weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. consult your approved dealer. maximum permissible all-up weight (mmac) Weights are indicated on the vehicle identification plate (refer to total train weight (mtR) the information on “Vehicle identification plates”...

  • Page 211: Replacement Parts And Repairs

    Replacement paRts and RepaiRs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.

  • Page 212: Service Sheets

    seRVice sheets Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □...
  • Page 213 seRVice sheets (continued) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 214 seRVice sheets (continued) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 215 seRVice sheets (continued) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 216 seRVice sheets (continued) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 217 seRVice sheets (continued) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...

  • Page 218: Anticorrosion Check

    anticoRRosion check If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.16...
  • Page 219 anticoRRosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.17...
  • Page 220 anticoRRosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.18...
  • Page 221 anticoRRosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.19...
  • Page 222 anticoRRosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.20...
  • Page 223 anticoRRosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.21...
  • Page 224 6.22...

  • Page 225: Alphabetical Index

    AlphABetiCAl inDex ABS ...............2.19 → 2.23 catalytic converter............2.6 – 2.7 accessories................ 5.28 central door locking ........1.8, 1.12 → 1.14 accessories socket ............3.21 changing a bulb .............5.12 → 5.19 additional methods of restraint .....1.22 → 1.25, 1.28 changing a wheel............5.7 – 5.8 side protection .............
  • Page 226 AlphABetiCAl inDex (continued) with manual controls ............ 1.16 electric beam height adjustment ........1.68 fuel electric windows ............3.11 → 3.13 advice on fuel economy ..........2.12 electronic parking brake ..........2.9 → 2.11 capacity ................ 1.72 Electronic Stability Program: ESP ......2.19 → 2.23 filling ..............1.72 →...
  • Page 227 AlphABetiCAl inDex (continued) dipped beam headlights ......1.65, 5.12 – 5.13 indicators ..............1.64, 5.12 direction indicators ....1.64, 5.12 – 5.13, 5.15 → 5.19 indicators: fog lights ......... 1.67, 5.14 – 5.15, 5.17 direction indicators ..........1.64, 5.15 hazard warning ............1.64 exterior temperature indicator ........
  • Page 228 → 3.13 functions ..............3.23 switching on the vehicle ignition .......... 2.4 rear view mirrors ............. 1.62 – 1.63 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.14 RENAULT card tailgate ..........3.24, 3.26, 3.28 – 3.29 battery ................5.26 tanks and reservoirs use ...............1.2 →...
  • Page 229 AlphABetiCAl inDex (continued) transporting children ......1.29 – 1.30, 1.32 → 1.36 transporting objects in the luggage compartment ........3.30 luggage net ............3.31 → 3.33 trims ..................5.6 trip computer and warning system... 1.45 → 1.48, 1.50 → 1.59 tyre inflation kit............5.3 → 5.5 tyre pressure........2.16 →...

  • Page 230: For Your Safety

    4 SIMPLE ACTIONS* FOR YOUR SAFETY • Always fasten • Always secure children • Adjust the height of • Place heavy objects or your seat belt, using devices suitable the seat belt according luggage at the back of the – even for short journeys for their size and weight to your size.
  • Page 231 à999108613Rë ê ó ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Table of Contents