Sony XAV-62BT Operating Instructions Manual page 76

Cautions
• Run all ground (earth) leads to a common ground
(earth) point.
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not disassemble or mOdify the unit.
• Do not install in locations which interfere with airbag
operation.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power supply leads only
after all other leads have been connected.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
• The use of optical instruments with this product will
increase eye hazard.
• Do not press on the LCD when installing the unit.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
than the sum of each component's fuse amperage rating.
• If no car circuits are rated high enough, connect the unit
directly to the battery.
Parts list
[j]
• The numbers in the list correspond to those in the
instructions.
• For XAV-62BT only: Assemble the parts of the
microphone
®
before use. For details, see "Installing the
microphone (XAV-62BT only) (II)" on the reverse side.
Connection example
[gJ
Notes
(II-A)
• Be sure to connect the ground (earth) lead before connecting the
amplifier.
• The alarm will only sound if the built-in amplifier is used.
Note
<II-B)
You cannot use multiple auxiliary devices simultaneously, even if they are
connected to different terminals. If you connect an optional device to BUS
CONTROL IN, AUX AUDIO IN is not available.
Note
on
satellite radio tuner til-B)
This unit does not support the XM radio tuner XMDSON 1 00.
http://www.sony.netl
Connection diagram
[I]
o
To a common ground (earth) point
First connect the black ground (earth) lead, then connect the yellow
and red power supply leads.
e
To the power antenna (aerial)
control lead
or the
power supply lead of the antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power antenna
(aerial) or antenna (aerial) booster, or with a manually-operated
telescopic antenna (aerial).
• If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see "Notes on the control and power supply leads:'
e
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
o
To the interface cable of a car telephone
o
To a car's illumination signal
Be sure to first connect the black ground (earth) lead to a common
ground (earth) point.
e
To the
+
12 V power terminal which is energized
when the ignition switch is set to the accessory
position
Notes
• If
there is no accessory position, connect to the
+ 12
V power
(battery) terminal which is energized at all times.
Be sure to first connect the black ground (earth) lead
to
a common
ground (earth) point.
• If your car has a built-in FM/AM antenna (aerial) in the rear/side
glass, see "Notes on the control and power supply leads."
G
To the
+
12 V power terminal which is energized
at all
times
Be sure
to
first connect the black ground (earth) lead to a common
ground (earth) point.
e
To the parking brake switch cord
®
To an auxiliary device such as a portable media
player, game console, etc. (not supplied)
Tip
You can use an RCA cord (not supplied) to connect auxiliary devices.
®
To the
+
12 V power terminal of the car's rear lamp
lead (only when connecting the rear view
camera)
Notes on
the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies
+
12 V DC when
you turn on the tuner.
• If your car has a built-in FM/AM antenna (aerial) in the rear/side glass,
connect the power antenna (aerial) control lead (blue) or the accessory
power supply lead (red)
to
the power terminal
of
the antenna (aerial)
booster. For details, consult your car dealer.
• A
power antenna (aerial) without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power supply lead is connected, power
will
always be
supplied to the memory circuit even when the ignition switch is turned
off.
Notes on
speaker connection
• Before connecting the speakers, turn the unit
off.
• Use speakers with an impedance
of 4
to
8
ohms, and with adequate
power handling capacities to avoid damage.
• Do not connect the speaker terminals to the car chassis, or connect the
terminals of the right speakers with those of the left speakers.
• Do not connect the ground (earth) lead of this unit to the negative (-)
terminal
of
a speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker leads installed in
your car if they feature a common negative (-) lead for the right and left
speakers.
• Do not connect the unit's speaker leads to each other.
Notes on connection
• If
"Output connection failure." appears in the display, make sure the
speaker and amplifier are connected correctly.
• To use the monitor for the rear seats, connect the parking brake switch
cord to the ground (earth).