Table of Contents
Advertisement
ENGLISH
Speaker Connections
I
Speaker SC·M37 (Supplied)
. 1
G)
' "
~ ,
"
l .C
~
III
~
' "
•
I
Ul
I
'"
I
~
I
c:
~
i
~
l
g
,
C">
'"
~
I
co
·
;:t
:;'
l.C
~
:r
' "
- i
3
~
r - -
SJ
:r
' "
I
~
I
.,.,
I
c:
I
"
I
n
f
~.
I
~
L..::-
I :;;
I
g
I
f
I
g
•
l.C
Ir -
.~
,~
Protector circuit
The protection circuit will be activated in the following cases:
• When the speaker cable's core wires are touching the rear
panel or screws or when the speaker cable's + and - sides are
touching
• When the surrounding temperature is extremely high
• When the internal temperature rises due to extended use with a
high output
If this happens, unplug the power cord, then check the connections
of the speaker cables and input cables. If the set's temperature
is extremely high, wait for it to cool off and improve surrounding
ventilation. After doing this, plug the power cord back in.
If the protection circuit is activated though there are no problems
in ventilation around the set or in connections, the set could be
damaged. Turn off the power, then contact a DENON servicing and
inquiry outlet.
U'n-
• Use speakers with an impedance of 6 to 16 O/ohms. The protection
circuit may be activated if speakers with an impedance other than
specified are used.
• Connect the speaker cables in a way that they do not stick out of the
speaker terminals. The protection circuit may be activated if the core
wires touch the rear panel or screws or if the
+
and - sides touch.
• Never touch the speaker terminals while the power is on. Doing so
could cause electric shock.
ct...>
When using a banana,plug
~~
Tighten the speaker terminal firmly before inserting the banana
plug.
1
Peel otT about 10 mm of the sheathing at
the tip of the cable, twist the core wire and
I
terminate it.
II
2
Thrn the speaker terminal counterclockwise
4\
to loosen it.
~~
4
Thm the speaker terminal counterclockwise
_..Jh
. to tighten it.
~
3
Insert the speaker cable's core wire into the
~
base of the speaker terminal.
r
I
Connecting
the Speaker Cables
I
Check the left (L) and right
(R)
channels and the + (red) and - (black)
terminals on the set and the speakers to be used and interconnect
the cables to the same polarities.
ILl
IRI
Subwoofer
with built-in
amplifier
(J
Ul
'0
co
£:
~.
c'
"
'"
9
ENGLISH
Protector circuit
The protection circuit will be activated in the following cases:
• When the speaker cable's core wires are touching the rear
panel or screws or when the speaker cable's
+
and - sides are
touching
• When the surrounding temperature is extremely high
• When the internal temperature rises due to extended use with a
high output
If this happens, unplug the power cord, then check the connections
of the speaker cables and input cables. If the set's temperature
is extremely high, wait for it to cool off and improve surrounding
ventilation. After doing this, plug the power cord back in.
If the protection circuit is activated though there are no problems
in ventilation around the set or in connections, the set could be
damaged. Turn off the power, then contact a DENON servicing and
inquiry outlet.
iN,na
• Use speakers with an impedance of 6 to 16 O/ohms. The protection
circuit may be activated if speakers with an impedance other than
specified are used.
• Connect the speaker cables in a way that they do not stick out of the
speaker terminals. The protection circuit may be activated if the core
wires touch the rear panel or screws or if the
+
and - sides touch.
• Never touch the speaker terminals while the power is on. Doing so
could cause electric shock.
Tighten the speaker terminal firmly before inserting the banana
plug.
When using a banana plug
Check the left
(L)
and right (R) channels and the + (red) and - (black)
terminals on the set and the speakers to be used and interconnect
the cables to the same polarities.
1
Peel otT about 10 mm of the sheathing at
the tip of the cable, twist the core wire and
I
terminate it.
II
3
Insert the speaker cable's core wire
int~
the
~
base of the speaker terminal.
r
4
Thm the speaker terminal counterclockwise
_~
. to tighten it.
~
2
Thm the speaker terminal counterclockwise
4\
to loosen it.
~1)V
I
Connecting the Speaker Cables
ILl
IRI
I
Speaker SC-M37 (Supplied)
. 1
Speaker Connections
Subwoofer
with built-in
amplifier
(J
9
Hide quick links:
Advertisement
Table of Contents
