Pioneer BDP-120 Service Manual page 34
Hide thumbs
Also See for BDP-120:
- Operating instructions manual (107 pages) ,
- Mode d'emploi (63 pages) ,
- System firmware update instructions (3 pages)
Table of Contents
Advertisement
1
QQ
3 7 63 1515 0
A
To Reset this Player
•
If this Player receives strong interference from a source such as excessive static electricity, strong external noise, malfunction
of power supply, or voltage caused by lightning during use or a wrong operation is sent to the Player, errors like the Player not
accepting an operation may occur. Press and hold STANDBY/ON on the Player until "
display when the Player does not operate properly even after the power has been turned off. Then, after the STANDBY/ON
indicator is lit, turn on the power.
•
When a reset is performed while the power is on, the Player will turn off. Turn the power on again. At this point, it may take
a few moments for the system processing to finish before the Player is ready for use. During the system processing, the
BD/DVD/CD disc indicator on the front panel display of the Player will blink. Once the system processing has finished, the
indicators will finish blinking and then light up normally. You can operate the Player when the BD/DVD/CD disc indicator is lit.
•
Since all settings including the language setting stored in memory are also reset when a reset has been performed, they must
be set again.
B
•
When the problem persists even after performing a reset, unplug the AC cord and plug it in again. If this does not solve the
problem, contact the nearest service center approved by Pioneer.
[3] On-screen Error Messages
Messages Relating to BD disc and DVD disc
•
The following messages appear on the TV screen in case the disc you tried to playback is not appropriate or the
operation is not correct.
C
Error message
C
a
n
n
t o
p
a l
. y
TE
L 13942296513
I
c n
o
m
p
a
b i t
e l
d
s i
. c
D
C
a
n
n
t o
o
p
r e
t a
. e
This USB memory is not formatted
properly. Please format the memory in
USB memory management.
The Connected USB Memory cannot
be used. It should be compliant with
USB 2.0.
E
Messages Relating to FAN MOTOR
•
When FAN motor is abnormal, the unit return to standby mode,
if the below message appear on the screen, check the FAN motor and the FAN motor control circuit
www
The Fan On the Rear Panel May Not Be Working Correctly, Check The Fan
F
34
1
http://www.xiaoyu163.com
2
Possible Error
•
T
h
e
i d
c s
c
a
n
this Player.
•
f I
o y
u
o l
a
d
a
played with this Player (i.e. a scratched
disc), or if you load a disc upside down,
this message will appear, and the disc
tray will automatically pop out.
•
Occurs if the loaded disc cannot be
played because it is a non-standard disc
or scratched, etc.
•
O
c c
u
s r
f i
a
n
•
Occurs if there is a formatting error.
•
Occurs if USB memory not compliant
with USB 2.0 High Speed (480Mbit/s) is
used (i.e. USB 1.0/USB 1.1).
Error message
x
ao
y
.
i
2
http://www.xiaoyu163.com
3
8
n
t o
b
e
p
a l
e y
d
b
a
k c
w
h t i
Q Q
3
6 7
1 3
i d
c s
w
h
c i
h
c
a
n
n
t o
b
e
o
p
e
a r
o i t
i n
i s
c n
o
r r
c e
. t
u163
.
BDP-120
3
4
2 9
9 4
2 8
" appears on the front panel
Suggested Solution
•
C
h
e
k c
h t
e
d
s i
, c
a
n
d
o l
a
d
t i
c
1 5
0 5
8
2 9
•
R
e
m
o
e v
h t
e
d
s i
. c
—
•
F
r o
m
t a
h t
e
U
S
B
m
e
m
o
y r
a
g
•
C
o
n
n
e
t c
U
S
B
2
0 .
H
g i
h
S
p
e
(480Mbit/s) compliant USB memory.
m
co
4
9 9
r o
e r
t c
. y l
9 4
2 8
9 9
a
. n i
e
d
Hide quick links:
Advertisement
Table of Contents
