Each Setting And Adjustment; Updating Software - Pioneer BDP-120 Service Manual

1

8. EACH SETTING AND ADJUSTMENT

QQ
3 7 63 1515 0

8.1 UPDATING SOFTWARE

A
NOTE: Be sure to update the firmware after the MAIN PWB unit is replaced.
(Updating can also be performed using the User menu. For details, refer to the operating instructions of the unit.)
1. Press [STANDBY/ON] button to turn the switch on, then wait till the BD/DVD/CD disc indicator changes from blinking to lit.
2. Press [OPEN/CLOSE] button to open the Tray, put the update disc on the tray and close the tray.
3. The power automatically turns off. Then it turns on again and the updating with the disc will start.
4. During the updating, the mode indicator stays blinking in white as "V-up" message keeps blinking on LCD.
"NOW UPDATING DO NOT UNPLUG AC CORD" appears on the monitor screen. And the version updating progress is
expressed in %.
5. When updating with the disc is completed, the Tray automatically opens.
* If the front-end software was updated, the STANDBY/ON indicator lights up halfway as well as the mode indicator starts
B
blinking alternately in white and blue.; the Tray will open after the updating is completed and the power will turn off. (Go to
step 8.)
6. When the updating is completed, the following appears on the monitor screen. : "SOFTWARE UPDATE IS COMPLETE"
If the version updating fails, "FAILED TO COMPLETE UPDATE RETRY SOFTWARE UPDATE" is displayed. Take out the
disc, turn off the power and take the procedure again starting from [1] above.
7. Remove the disc from the Tray and press any other button of the Main Unit than [STANDBY/ON], then the Tray will close and
the power will automatically turn off. (Confirm the power-off by stop of the Cooling Fan.)
* If [STANDBY/ON] button is pressed, the power will turn off with the Tray open.
8. Press [STANDBY/ON] button to turn the power on, then wait till the STANDBY/ON indicator changes from blinking to lit.
9. Press the [HOME MENU] button on the remote controller, and the menu screen shows up (if the wallpaper screen is used).
C
* There is no need to take this step, because just after the power is turned on, the menu screen shows up.
10. Select [SETTINGS] first and then [VERSION]. (Press the ENTER button.)
11. The version of the currently installed software appears on the monitor screen. Compare with the version of this updated
software, make sure the version is just the same. If the version is not updated, take the procedure again from Step [2].
TE
L 13942296513
12. Press [STANDBY/ON] button to turn the power off. (Confirm the power-off by stop of the cooling fan.)
NOTE: Do not unplug the AC cord during version updating.
Start
Turn the power on.
D
Open the tray, put the
update disc and close the
tray.
The power automatically
turns off. Then, the power
turns on automatically and
the updating starts.
E
Monitor:
"NOW UPDATING DO
NOT UNPLUG AC CORD"
ex.
www
The tray opens
automatically.
F
*The version updating cannot be made on the menu screen. Make the wallpaper onscreen.
Monitor: "CANNOT UPDATE. FINISH PLAYBACK OR EDIT AND SET A DISC"
40
1
http://www.xiaoyu163.com
2
Monitor:
"SOFTWARE UPDATE IS
COMPLETE"
Remove the disc and turn
the power off.
Turn the power on and
confirm the version.
20%
Updating successful.
x ao
y
. i
2
http://www.xiaoyu163.com
3
8
Q Q
3 6 7 1 3
No
Updating
completed
Yes
u163
.
End
BDP-120
3
4
2 9 9 4 2 8
1 5 0 5 8 2 9 9 4
Monitor:
"FAILED TO COMPLETE
UPDATE RETRY
SOFTWARE UPDATE"
Remove the disc and turn
the power off.
m
Updating unsuccessful.
co
Restart
4
9 9
2 8 9 9