Advertisement
Quick Links
Contents
013-100163 Rev. 1 (07/05)
NOTE: Due to constant research, the information in this manual is subject to change without notice
(legacy: 54-017201-02P)
Installation Manual
Overview ...............................................................................................................................1
Components Shipped ............................................................................................................. 1
Installation and Setup Process ...............................................................................................2
Pre-Installation Considerations..............................................................................................2
Installation and Setup Instructions.........................................................................................3
Appendix A : Technical Information...................................................................................15
R P M X - 1 0 0 U
Advertisement
Related Manuals for Christie Graph-X-Master RPMX-100U
Summary of Contents for Christie Graph-X-Master RPMX-100U
-
Page 1: Table Of Contents
R P M X - 1 0 0 U Installation Manual Overview ..........................1 Contents Components Shipped ......................1 Installation and Setup Process ....................2 Pre-Installation Considerations....................2 Installation and Setup Instructions..................3 Appendix A : Technical Information...................15 013-100163 Rev. 1 (07/05) NOTE: Due to constant research, the information in this manual is subject to change without notice (legacy: 54-017201-02P) -
Page 2: Overview
In addition to the contents of the User’s Kit, you should have the following tools on hand during installation and setup. • Screwdriver (#1 Phillips) • Level NOTE: Optional CHRISTIE components such as screens, pedestals, and other accessory kits are purchased and packaged separately. RPMX-100U Installation Manual... -
Page 3: Installation And Setup Process
Installation and Setup Process STEP Refer to Page STEP 1 – Unpack the projector STEP 2 – Modify Projector Configuration STEP 3 – Projector Position and Mounting STEP 4 – Connect Sources STEP 5 – Power Projectors On/Off STEP 6 – Adjust Projection Lens STEP 7 –... -
Page 4: Installation And Setup Instructions
Other Considerations Here are some other considerations and tips that can help you improve your installation: • Ventilation is an important factor when preparing a projection room. The ambient temperature should be kept constant and below 35°C (95°F). Keep the projector away from heating and/or air conditioning vents. - Page 5 Figure 1. 3. Remove the PHM. See Figure 2. Figure 2. 4. Remove the mounting bracket on the adjuster used for mounting the PHM assembly in a lens horizontal configuration. 5. Install the mounting bracket required for lens vertical configurations on the adjuster.
- Page 6 6. Flip the PHM so the lens is pointing up (90 degrees). Lower it back down on the adjuster aligning the mounting holes on the PHM with the new mounting bracket on the adjuster installed in Step 5. Secure the PHM in its new position using the four wing nuts removed in Step 1.
- Page 7 Step 3 - Projector Position and Mounting Calculating Projection Applies to RPMX-100U (38-GFX101-01) only Distance Figure 5. RPMX-100U Installation Manual...
- Page 8 Applies to RPMX-100U (38-GFX101-02) only Figure 6. RPMX-100U Installation Manual...
- Page 9 Applies to RPMX-100U (38-GFX101-05) only RPMX-100U Installation Manual...
- Page 10 Mounting A few things to consider when mounting a projector: • Mount the projector on a sturdy, flat surface. Otherwise, you will have issues with tipping, movement, and image geometry problems. • Choose a platform that has a large enough surface area. The projector must be secured to the platform using all four of its mounting points.
- Page 11 Press and hold for approximately 1 second to turn the projector on or off with a POWER single key press. Or press followed immediately by if you want to guarantee the correct toggle (useful if you are unsure of the present status). When powering down, the cooling fans in the projector stay on for approximately 30 seconds before turning off.
- Page 12 For RPMX-100U (38-GFX101-02 and -05): 1. Loosen the lock screw on the barrel of the lens. (Figure 9., top) 2. Grasping the lock screw, slide it to the left and right until the desired focus is achieved. (Figure 9., bottom) 3.
- Page 13 Figure 10. Step 7 ñ Adjust Image Geometry The projection head module is mounted to a uniquely designed 6-axis adjustment mechanism that is used during the setup process to fine-tune the geometry of the image. It does this by moving the module about the X, Y and Z-axes in varying degrees.
- Page 14 Zoom the image out (make smaller) until it fits within the borders of the screen. 4. Adjust keystone and tilt. 5. Zoom the image in (make larger) to fill the screen. 6. Repeat any adjustments if necessary, until the image appears correct. 7.
- Page 15 6. Select Auto Setup from the main menu, to give the projector a chance to setup the best possible settings for the chosen incoming signal. 7. Verify options in the menu Video Options are correct for the chosen signal. 8. Change Resize Presets if you want the image displayed at any other resolution other than native.
-
Page 16: Appendix A : Technical Information
Appendix A Technical Information RPMX-100U (38-GFX101-01) Dimensions Lens Horizontal Lens Vertical Weight Includes adjuster, but not projection lens <44lbs RPMX-100U Installation Manual... - Page 17 RPMX-100U (38-GFX101-02) Dimensions Lens Horizontal Lens Vertical RPMX-100U Installation Manual...
- Page 18 RPMX-100U (38-GFX101-05) Dimensions Lens Horizontal Lens Vertical RPMX-100U Installation Manual...
- Page 19 Interconnections Drawing NOTE: The IR PCB is located in the electronic module in RPMX (38-GFX101-01) and in the PHM in RPMX (38-GFX101-02/05). In both cases, the IR PCB connects to the Control PCB. RPMX-100U Installation Manual...