Icom VE-PG2 Easy Configuration Manual

Easy configuration guide
RoIP GATEWAY
VE-PG2
NOTE:
• To set the VE-PG2 to "Converter mode," see "Converter mode guide" for that mode's explanation and setting details after
reading below "1. Select the VE-PG2 to the easy configuration wizard" for the easy configuration wizard screen explanation.
• Connect the transceiver to only the VE-PG2's [TRX1] port.
You cannot set the VE-PG2's [TRX2] and [TRX3] ports using the easy configuration wizard.
• Set the SIP server's setting first when you set the VE-PG2 to the converter mode.
The easy configuration can set the VE-PG2 only to SIP server sending.
To set the VE-PG2 to Peer to Peer sending, use the detail setting mode.
• To connect the transceiver to VE-PG2's [TRX2] and [TRX3] ports, use the detail setting mode.
To set the VE-PG2's external input or external output to ON, use the detail setting mode.

1. Select the VE-PG2 to the easy configuration wizard

Click
When you switch from the VE-PG2's "Easy configu-
ration mode."
Click
About the easy configuration wizard screen
This guide describes the easy configuration wizard of
"Bridge mode" and "Selective call mode," and includes a
connection example.
When you use only the [TRX1] port, you can easily setup
the VE-PG2 using the easy configuration wizard.
Read "PRECAUTIONS" first, if you have not read it.
Read this guide after reading "Installation guide q" for the
transceiver settings.
Click "switch to the easy configuration mode" in the "Setting
mode," then the VE-PG2 is set to the easy configuration
wizard.
If you click "Switch to detailed configuration mode," the
VE-PG2 is set to the detail setting mode.
"Change operating mode"
When you click "Switch to detailed configuration mode,"
the VE-PG2 is set to the detailed configuration mode.
"Operating mode setting"
You can change or confirm the VE-PG2's operating mode.
Select the operating mode, and then click "Save and
Reboot," to change the operating mode.
"Config Wizard"
When you click "Begin wizard," the VE-PG2 starts the
easy configuration wizard.
"Connection setting"
You can change or confirm the VE-PG2's settings. If
you click "Save and Reboot," the VE-PG2 registers the
settings after the reboot is completed.
• You can change the VE-PG2's settings in both the bridge mode
and the converter mode.
"Cancel"/"Save and Reboot" buttons
You can cancel the VE-PG2's setting by clicking "Cancel."
When you click "Save and Reboot," the VE-PG2 registers
the settings after the reboot is completed.

2. Start the easy configuration wizard

Sets the VE-PG2 to the Bridge mode
1. Confirm the VE-PG2's "Operating mode"
Confirm that the VE-PG2's "Operating mode" is set to
"Bridge mode" in "Operating mode setting."
• Default setting is "Bridge mode."
Confirm
2. Start the configuration wizard
When you click "Begin wizard," the VE-PG2 starts the
setting wizard.
Click
• To set the VE-PG2 to the multicast mode, see "When you
set the VE-PG2 to the bridge mode (multicast mode)," as
shown below.
• To set the VE-PG2 to the unicast mode, see "When you
set the VE-PG2 to the bridge mode (Unicast mode)," as
shown on the reverse side.
NOTE: When you set the VE-PG2 to the Converter mode, see "Converter mode guide" for details.
' When you set the VE-PG2 to the bridge mode (multicast mode)
This explanation describes how you set the VE-PG2 to the bridge mode (multicast mode) using the easy configuration wizard
with the connection shown below.
Multicast mode connection example
[Area A]
+ + +
MODE DC LAN TRX1 TRX2 TRX3 IN OUT SW ABC
VE-PG2
192.168.0.1
Connect the transceiver to the
VE-PG2's [TRX1] port.
CAUTION:
To connect the transceivers or repeaters, use only the following cables: OPC-2073 (For the transceivers) or
OPC-2074 (For the repeaters).
Using another cable, like an Ethernet cable, may damage the VE-PG2, transceivers or repeaters.
1. "IP Address setting" setting
Click "Next>>" when "Start the Easy Setup Wizard for
Bridge mode configuration" is displayed on the web
browser.
Enter the VE-PG2's IP address and subnet mask in "IP
address" and "Subnet mask."
• Set the default gateway when your VE-PG2 communicates with a
network device which has a different network IP address.
Click "Next>>"after you finish entering the VE-PG2's IP
address and subnet mask.
(Example) Enter "192.168.0.1" into the VE-PG2 in Area A, and
"192.168.0.2" into the VE-PG2 in Area B in the illustration above.
q Enter
w Click
• The setting screen is the VE-PG2's setting display in Area A.
Sets the VE-PG2 to the Selective call mode
1. Set the VE-PG2's "Operating mode"
Set the VE-PG2's "Operating mode" to "Selective call mode"
in "Operating mode setting," then click "Save and Reboot."
q Select
2. Start the configuration wizard
When you click "Begin wizard," the VE-PG2 starts the
setting wizard.
To set the VE-PG2 to the selective call mode, see "When
you set the VE-PG2 to the selective call mode," as shown
on the reverse side.
[Area B]
VE-PG2
192.168.0.2
+ + +
MODE DC LAN TRX1 TRX2 TRX3 IN OUT SW ABC
IP
network
Connect the transceiver to the
VE-PG2's [TRX1] port.
2. "IP communication mode setting" setting
Select "Multicast mode" in "IP communication mode setting,"
then click "Next>>."
q Select
3. Confirm the VE-PG2 settings
Confirm the VE-PG2 settings at "Verify setting," then Click
"Save and Reboot" to set the settings to the VE-PG2.
• If you want to change the VE-PG2's settings, click "<<Back."
q Confirm
• The setting screen is the VE-PG2's setting display in Area A.
w Click
Click
w Click
w Click