Sony KL-W9000A Service Manual page 10

Connecting to video equipment
To a VCR not equipped with an S video
connector
Rear of the monitor
VIDEO IN
VIDEO
OUT
1 3 DVD
Y S VIDEO
S VIDEO C /P
B B
VIDEO
C /P
R R
to VIDEO 1 IN or
VIDEO
VIDEO 3 IN
L
AUDIO
R
VMC-810S/820S
RGB 1 IN
(not supplied)
AUDIO
RGB
R L
to video/audio outputs
VCR
You can also use the VIDEO 2 IN jacks on the front of
the monitor for the video/audio connections.
To an S video equipped VCR
Rear of the monitor
VIDEO IN VIDEO
1 3 DVD OUT
Y
S VIDEO
S VIDEO C /P
B B
VIDEO
C /P
R R
to VIDEO 1 IN or
VIDEO
VIDEO 3 IN
L
AUDIO
R
YC-810S
RGB 1 IN
(not supplied)
AUDIO
RGB
R L
to S video/audio outputs
VCR
Note
• When you connect the cable to both the VIDEO jack and the S
VIDEO connector, the picture from the S VIDEO connector is
displayed on the monitor screen.
10 -US
Getting Started
Connecting two VCRs for editing
The monitor outputs the signal, which is input from the
VIDEO 1 IN, VIDEO 2 IN or VIDEO 3 IN jacks, through
the VIDEO OUT jacks. With two VCRs connected to the
VIDEO IN and VIDEO OUT jacks, you can edit the
tape.
Notes
• For signals input from the RGB 1 IN, RGB 2 IN and
DVD IN connectors, the monitor outputs only the
audio signal.
• Do not connect both the VIDEO IN and VIDEO OUT
jacks on this monitor simultaneously to the video/
audio output and input jacks on a single VCR.
Rear of the monitor
VIDEO IN
VIDEO
OUT
1 3 DVD
Y S VIDEO
to VIDEO 1 IN
S VIDEO C /P
B B
or VIDEO 3 IN
VIDEO
C /P
R R
to VIDEO OUT
VIDEO
L
AUDIO
R
RGB 1 IN
AUDIO
RGB
R L
VMC-810S/820S VMC-810S/820S
(not supplied) (not supplied)
to video/
to video/audio
audio
outputs
inputs
VCR for playback VCR for recording
Connecting a DVD Player
If your DVD player has the component video output
connectors*, connect them to the DVD IN (Y, C /P
B B
and C /P ) connectors at the rear of the monitor for
R R
higher quality picture. For details, see the Instructions
supplied with the DVD player.
* Some DVD player terminals may be labeled or
colored differently. If so, connect them as follows:
Connect (on the monitor) To (on a DVD player)
Y (green) Y
C /P (blue) C , C , B-Y or P
B B B b B
C /P (red) C , C , R-Y or P
R R R r R
Connecting a DVD player with
component video output connectors
Rear of the monitor
to DVD IN
VIDEO IN VIDEO
1 3 DVD OUT
Y
S VIDEO
S VIDEO C /P
B B
VIDEO
C /P
R R
VIDEO
L
AUDIO
R
RGB 1 IN
AUDIO
RGB
L
R
to audio
outputs
VMC-10HG (not supplied)
to component video outputs
DVD player
Note
• The signal input from the DVD IN jacks is not output from the
VIDEO OUT jacks.
Connecting a DVD player without
component video output connectors
Rear of the monitor
VIDEO IN
VIDEO
1 3 OUT
DVD
to VIDEO 1 IN or
Y S VIDEO
VIDEO 3 IN
S VIDEO C /P
B B
VIDEO
C /P
R R
VIDEO
L
AUDIO
R
VMC-
810S/
RGB 1 IN
820S (not
AUDIO
supplied)
RGB
R L
to audio/
video
outputs
DVD player
Note
If you have an S video equipped DVD player, make an
S video connection using the S video connecting cord
(not supplied) instead of the yellow video connecting
cord. If so, you can obtain the high quality picture.
Connecting the AC power cord
Connect the supplied power cord to the AC IN socket
of the monitor and to a wall AC outlet.
Rear of the monitor
to AC IN
to an AC outlet
AC power cord
(supplied)
Getting Started 11 -US
US