GMC 1990 Light Truck Repair Manual page 233

• The open side of the thrust block must face toward
the small window opening.
7. Pinion shaft (18).
8
. A new lockscrew (3). Install finger tight.
• Tighten to specifications after its in the
vehicle.
9. Governor assembly (23) and latching bracket (11).
• The straight end of the latching bracket spring
must be over and outside the governor
assembly shaft (figure
91 2
10. Stop pin (2) ( / -inch)
• Press the pin flush with the case.
11. Governor bushing (4).
• Use the bushing with a straight hole, not a
tapered hole.
• Press the bushing in far enough to give 0.004
0 020
to . -inch shaft end play.
12. Latching bracket bushing (5).
• Press in far enough to eliminate all end play.
101/2-INCH
DISASSEMBLY OF THE DIFFERENTIAL
□ Remove or D isconnect (Figure 9)
Tools Required:
J 22912-01
1. The ring gear and differential side bearings. Refer to
"D issasem bly of the Rear A x le " under the
101 2
" / -lnch Ring Gear" heading.
2
. Case screws (32).
— Set the unit on the right side case half.
3. Case halves (figure 10).
• Pry the halves apart at the yoke hole location.
• Hold the side gear in the left side case half.
4. Governor assembly (48).
5. Latching bracket assembly (43).
6
. Left side gear (46).
7. Left side clutch pack and guide clips (47).
8
. Left thrust washer (45).
9. Reaction blocks (41), pinion yoke (42), pinion gears
(39), and pinion thrust washers (38).
8
).
r in g g e a r
LOCKING DIFFERENTIALS 4B7-5
10. Right cam unit from the differential.
11. Right thrust washer (36).
• Measure and record the overall length of the
gear assembly from the front of the gear to the
back of the thrust sleeve (35) including the
side gear washer (36).
12. Thrust sleeve (35) using J 22912-01.
• Press the sleeve from the side gear (figure 11).
13. Clutch plates.
14. Guide clips (34).
15. Wave spring.
16. Cam plate (33).
17. Cam side gear (40)
CLEANING AND INSPECTION
Clean
All parts with solvent.
Inspect
L*
• All parts for excessive wear and breakage.
• Pinion gear and side gear teeth for wear, cracks,
scorring, and spalling.
• Thrust washers for wear.
• The fit of the side gears on the axle shafts.
• Differential case for cracks and scorring.
• Thrust sleeve for excessive wear. Do not replace the
thrust sleeve unless necessary. Inspect the side
gear bore for scorring. If scorring is present, replace
the entire differential.
• If any damage to the differntial case is found, the
entire differential must be replaced.
• Replace parts as necessary.
CAM UNIT ASSEMBLY
Install or Connect (Figure 9)
Cam plate (33) to the cam side gear (40).
1.
2. Wave spring.
3. Clutch plates.
• Alternate the plates, and position the wave
spring as shown in figure
4. Thrust sleeve (35).
• Press the thrust sleeve flush with the side gear
disc spline.
5. Guide clips (34) to the plates.
• Use grease in the clips to hold them in place
on the plates.
• If the side gear or thrust sleeve has been replaced,
measure and record the overall length of the gear to
the back of the thrust sleeve (35) including the side
gear thrust washer (36).
• Compare this reading with the reading obtained
earlier in this section.
• If the new reading is more than 0.003-inch higher or
lower than the original, select a thrust washer that
will return the reading closest to the original
reading.
12
.