Advertisement
Ventosa
Model: VNS15
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice:
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electrical
shock and injury to persons, including the following:
If the appliance is damaged, check with the supplier before
installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower
or swimming pool.
Do not locate the heater immediately below a fixed socket
outlet or connection box.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they
do not play with the appliance.
Do not use this heater in series with a thermal control, a
program controller, a timer or any other device that
switches on the heat automatically, since a fire risk exists
when the heater is accidentally covered or displaced.
This heater is not equipped with a device to control the
room temperature. Do not use this heater in small rooms
when they are occupied by persons not capable of leaving
the room on their own, unless constant supervision is
provided
Ensure that furniture, curtains or other combustible
material are positioned no closer than 1 metre from the
heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we
do not recommend its use on deep pile carpets or on long
hair type of rugs.
The appliance must be positioned so that the plug is
accessible.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
WARNING: In order to avoid overheating, do not
cover the heater. Do not place material or
garments on the heater, or obstruct the air
circulation around the heater. The heater carries
the Warning symbol indicating that it must not be
covered.
General
Unpack the heater carefully and retain the packaging for
possible future use, in the event of moving or returning the
fire to your supplier.
The fire incorporates a flame effect, which can be used with
or without heating, so that the comforting effect may be
enjoyed at any time of the year. Using the flame effect on its
own only requires little electricity.
These models are designed to be free standing and are
normally positioned against a wall.
Before connecting the heater check that the supply voltage is
the same as that stated on the heater.
Please note: Used in an environment where background
noise is very low, it may be possible to hear a sound which
is related to the operation of the flame effect. This is normal
and should not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the supply
voltage.
Before switching on, please read the safety warnings and
operating instructions.
Wall fixing - see Fig. 1
The appliance should be securely fixed to the wall via the chain
to the rear of the product using the wall plug and screw supplied
for block walls.
Note - for studded walls special fasteners are required, see
diagram for recommended position of fixing screws.
Controls - see Fig. 2
Three switches provide a choice of heat settings. The
appliance is in standby mode when the mains lead is plugged
in. The two selector switches are in the ON position when the
side with the markings on (i.e. I, or II) are pushed in.
Stand-by Switch 1
Controls the electricity supply to the heater
and flame effect.
Selector Switch 2 (I) Provides 750W heat output.
Selector Switch 3 (II)Provides 1500W output with Switch 2.
(Remote Control - 1/0)
and press again to return to 'Standby'
mode ( Alternatively use t he Remote Control).
If both selector switches 2 and 3 are in
the OFF position, the product works on
flame effect only.
Remote control - see Fig. 6
The maximum range of use is ~ 10metres.
Warning: It takes time for the receiver to respond to the transmitter.
Do not press the buttons more than once within two seconds for
correct operation.
Battery information - see Fig. 6
1. Slide open the battery cover on the back of the remote control.
2. Install AAA batteries into the remote control.
3. Replace the battery cover.
Discard leaky batteries
Dispose of batteries in the proper manner according to
provincial and local regulations.
Any battery may leak electrolyte if mixed with a different battery
type, if inserted incorrectly, if all the batteries are not replaced
at the same time, if disposed of in a fire, or if an attempt is
made to charge a battery not intended to be recharged.
Thermal Safety Cut-out
The built-in overheat cut-out switches of the appliance
automatically in the event of a fault! Switch off the appliance or
disconnect the mains plug from the socket. After a short cooling
down phase, the appliance is ready for use again! If the fault
should occur again, see your local dealer!
WARNING: In order to avoid a hazard due to inadvertent resetting
of the thermal cut-out, this appliance must not be supplied
through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by the
utility.
Press once to operate the product
UK
Advertisement
