Classic Series Custom Panels - KitchenAid 2316565B Installation Manual

If you plan to install custom wood panels, you will need to create
the panels yourself or consult a qualified cabinetmaker or
carpenter. See dimension drawings for panel specifications.
IMPORTANT: Panels weighing more than recommended may
cause damage to your refrigerator.
NOTE: Dimensions shown have a (
Panels that are more than
panels are less than " (6.35 mm) thick, install a filler panel
between the doors and decorative panels.
Top Grille Panel
The top grille panel should not weigh more than 10 lbs (4.5 kg).
NOTE: The dashed lines in the illustration represent the location
and offsets of raised wood panel.
7"
(17.78 cm)
Top & Bottom Offsets
" thick
plywood
Model A
36
42
48
Door Panels for Non-dispenser Models
The freezer panel should not weigh more than 40 lbs (18.1 kg).
The refrigerator panel should not weigh more than 50 lbs (23 kg).
A
"
(1.27 cm)
Freezer
Door
(Non-Dispenser)
(178.9 cm)
" thick
plywood
3 "
(8.3 cm)
"
"
(1.1 cm)
(1.27 cm)
Model A
36 14 " (36.2 cm)
42 16 " (42.6 cm)
48 19 " (48.9 cm)
16

Classic Series Custom Panels

" (1.5 mm) tolerance.
" (6.35 mm) thick must be routed. If
A
Side Offsets
" (1.11 cm)
" (1.75 cm)
34 " (87.0 cm)
40 " (102.2 cm)
46 " (117.5 cm)
B
(1.27 cm)
Refrigerator
Door
70 "
3 "
(8.3 cm)
Location and offsets
of raised wood panel
(1.27 cm)
B
19 " (48.9 cm)
22 " (57.8 cm)
26 " (66.7 cm)
NOTES:
If the standard handle is used, the handle side offset of both
panels should be 3 " (8.25 cm) to allow for finger clearance.
If an extended handle is used, the handle side offset of both
panels should be
location allows the doors with extended handles to open to 90
degrees. See "Door Swing Dimensions."
The dashed lines in the illustration represent the location and
offsets of raised wood panel.
Door Panels for Dispenser Models
The freezer panel should not weigh more than 40 lbs (18.1 kg).
The refrigerator panel should not weigh more than 50 lbs (23 kg).
"
(1.27 cm)
" thick
plywood
14 "
(36.2 cm)
33 "
"
(85.7 cm)
"
"
(1.1 cm)
(1.1 cm)
Model A
36
42
48
" thick
plywood
NOTES:
Dispenser cut-out is centered left-to-right.
If the standard handle is used, the handle side offset of both
panels should be 3 " (8.25 cm) to allow for finger clearance.
If an extended handle is used, the handle side offset of both
panels should be
location allows the doors with extended handles to open to 90
degrees. See "Door Swing Dimensions."
The dashed lines in the illustration represent the location and
offsets of raised wood panel.
"
" (1.1 cm). Make sure the refrigerator
A
Freezer
Refrigerator
Door
(Dispenser)
10 "
(27.6 cm)
70 "
(178.9 cm)
Dispenser
cut-out is
centered
left-to-right
3 "
(8.3 cm)
Location and offsets
"
of raised wood panel
(1.27 cm)
B
14 " (36.2 cm) 19 " (48.9 cm)
16 " (42.6 cm) 22 " (57.8 cm)
19 " (48.9 cm) 26 " (66.7 cm)
" (1.1 cm). Make sure the refrigerator
B
"
(1.27 cm)
Door
"
(1.1 cm)
" thick
plywood
3 "
(8.3 cm)
"
(1.27 cm)