Page 1
D – 3 5 7 4 5 H e r b o r n Deutschland Germany Email: Info@rittal.de http://www.rittal.com Service -Tel. : (+49) - (0)2772 / 505 - 0 Service - Fax : (+49) - (0)2772 / 505 - 2319...
Page 2
Microsoft Windows is a registered trademark of Microsoft Corporation. Acrobat Reader is a registered trademark of Adobe Systems Incorporated.
5.2. Start-up in Battery Mode (Cold Start)..20 Table of Contents 5.3. Check Measured Values & Figures detected by UPS ...........21 5.4. UPS Default Data and Special Function IMPORTANT SAFETY Execution ..............22 INSTRUCTIONS ........5 5.5. UPS Default Settings and their 1.1. Documentation Notes .......
5. Do not install the UPS in an environ- Rittal cannot accept any liability for damage ment with sparks, smoke or gas. and operational malfunctions that result from 6. This UPS is equipped with an EMI filter.
1.5. Proper Use This UPS is designed for providing power to IT systems. A use different from that described here is considered to be an improper use. Rittal cannot accept any liability for damage resulting from the improper use or the non-observance of this guide.
Product Introduction 2. Product Introduction 2.2. Special Features 2.1. General Characteristics The transformer-free converter technology with a housing that can be mounted in a rack or used as double-conversion technology floor-standing enclosure allows the UPS to be accordance with the specification VFI-SS 111 integrated even in environments with restricted guarantees the power supply to connected space.
UPS Functional Descriptions 3. UPS Functional Descriptions of the UPS. ⑫ 3.1. UPS Front Panel Display To re-confirm the change of UPS Setting 3.1.1. Symbols DisplayPanel Item Symbol Description Utility or Bypass LINE Source Battery Low Battery Abnormal UPS Overloading Working Service Mode A Blackout...
Page 9
UPS Functional Descriptions Previous Page or CVCF mode with Er24 Setting Change Bypass input Next Page The UPS must be operated in normal Er27 Special Function mode in parallel Log in /out system Enter or Bypass Overload Reconfirmed Er28 Time out and cut off output Utility Input Normal The settings of...
UPS Functional Descriptions 3.2. Rear Panel Descriptions A Terminal Resistor for Parallel function B RS232 Port C EPO Port D Utility Input Breaker E CAN Bus Connection Port for Parallel System F External Battery Connector G Cooling Fan H Utility Input &UPS Output Power Connector I Customer Options Slot J Slot 3.2.1.
UPS Functional Descriptions 3.3.1. EPO (Emergency Power Off) 3.3. Communication Port Explanation The Pin assignments of the EPO Input port are: The Communication port on the UPS provides true RS232 type communication with the UPS software to remotely monitor the power and UPS status.
Installation 4. Installation Warning! Please thoroughly read the Safety Instructions (chapter 1.4) before installing the UPS 4.1. Unpacking Inspect the delivery conditions of the UPS upon receipt and notify the freight forwarder and the dealer in case of any visible damage of the packing of the product The packaging is recyclable;...
Installation 4.2. Selecting Installation Position Warning! The UPS is heavy. Select a location sturdy enough to handle the UPS weight. To ensure proper operation and long operating life, always position the UPS according to the following criteria: Relative Humidly (non condensing) 30%~90% Keep minimum 30cm (12 inches) distance clearance from the rear panel of the UPS to avoid any obstructions.
Installation 4.3. Assembling different System Components 4.3.1. Tower Assembling steps 4.3.1.1. Power Module + Battery Module Step1: Mounting of Foot Cover and Power Module UPS-Manual...
Installation Step2: Installation of Power Module and Battery Module 4.3.2. Rack installation step 4.3.2.1. Power Module+ Battery Module Step1: Mounting of Ear Handle B1 B2 S4 B1 B3 S4 UPS-Manual...
Page 16
Installation Step2: Installation of Ear Cover to Power and Battery Module Step3: Installation of Rail to Rack Step4: Installation Battery Module to Rail UPS-Manual...
Page 17
Installation Step5: Installation Power Module UPS-Manual...
Installation 4.4. Electrical Installation Connect the UPS with the parallel hot swap chassis (DK7857.443 or DK7857.444), the external bypass (DK7857.441) with installation cable DK7857.446. Please make sure, that the parallel hot swap chassis, the external bypass or the installation cable is installed correctly.
Operation 5. Operation 5.1. Start-Up In Normal Mode • Connect the Utility to the parallel hot swap chassis or the installation cable. Switch on the Power Breaker of the distribution panel and the breakers of the Fig. C UPS’ Utility and Bypass Inputs, and then the UPS starts up.
Operation and then the buzzer sounds twice. The LCD display will illustrate from Fig. A to Fig. G, and keep awake for approx. 15 seconds. • Press the UPS On Switch of the UPS again for about 3 seconds till the LCD display illustrates from Fig.
Operation 5.3. Check Measured Values & Figures detected by UPS If you would like to check the measured values & figures detected by the UPS, please use scroll down and scroll up pads. When you use scroll down key pad, the Fig.
Operation 5.4. UPS Default Data and Special Function Execution • After the UPS completes start up, press key pad to change the LCD display screen to Fig. Q1. Fig. R2: It shows self-test is “On” Fig. Q1: It shows buzzer “On” Fig.
Page 23
Operation Fig. W: It shows Output Voltage Adjustment Fig. V1: It shows the UPS is operated in % from 0% to 3% or -0% to -3% “normal mode” Fig. X: It shows UPS Identification Number Fig. V2: It shows the UPS is operated in “Eco mode”...
Operation press “OFF” key pads for 5 seconds, then 5.5. UPS Default Settings and their the LCD screen turns to Fig. AA directly, alternatives which means your setting changes are • Make sure the UPS is not “On” yet. Press invalid.
Otherwise, consult your local warranty will be void immediately. distributor for service. • Press Off key pad for 5 • Press the Off key pad for approx. 5 seconds and buzzer will sound seconds, the LCD screen shows as Fig. twice.
Troubleshooting Guide 6. Troubleshooting Guide 6.1. Troubleshooting When the UPS malfunctions during operation, you may check the following: a. Is the input and output wiring correct? b. Is the input voltage of the Utility within the input window of the UPS? In case of problems or if symptoms still exist, please carry out the following steps.
7. Bundled Software Installation 8. Optional Communication Card Guide The Simple Network Management Protocol (SNMP) worldwide-standardized communication-protocol. It is used to monitor 7.1. Hardware Installation any device in the network via simple control language. The UPS-Management Software 1. Connect the male connector of RS232 also provides its data in this SNMP format cable to the UPS communication port.
Optional Communication Card shut down possible without additional SNMP 8.2. Internal SNMP Adapter management software. For detailed information please see Software Manual provided with the PMC-Software CD ROM.RCCMD Remote Console Command module multi-server shutdown. This stand-alone software module is designed to receive and execute a command issued by a remote device.
Step 2. 3. Remove the screw of the battery pack as shown in Step 3. Customer Service If you have any technical questions or questions concerning our product spectrum, contact the following service address: Tel.: +49 (0)2772/505-1855 http://www.rimatrix5.com E-mail: info@rittal.de UPS-Manual...
Technical Data Technical Data Model 4,5 kVA 6 kVA INPUT Voltage Window 160~280 VAC* Frequency 45 ~ 65 Hz Phase/Wire Single, Line + Neutral + Ground Power Factor Up to 0.99 at 100% Linear Load Current THD <6% at 100% Linear Load OUTPUT Voltage Window 220/230/240 VAC Selectable...
Page 31
Battery Bank Dimensions Convertible(Rack/Tower) BBC20J0007(20pcs 12V/7AH) 440x133x660(3U) Battery Bank Net Weight Convertible(Rack/Tower) BBC20J0007 w/o bat./with bat. 18 kg/ 68 kgs ENVIRONMENT Operating Temperature 0° C to 40° C The battery design life is based on a temperature 25° Ambient Temperature Warning temperature above this range will reduce battery life.