Related Manuals for WeatherBug HD MotionCam
Summary of Contents for WeatherBug HD MotionCam
- Page 1 High Definition Motion Camera System Installation, Operation, and Maintenance Manual February 2011 Release 1, Version 1.0...
-
Page 2: Copyright
All Rights Reserved. Information in this document is subject to change without notice and does not represent a commitment on the part of AWS Convergence Technologies, Inc. FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 3: Disclaimer
The procedures, methods, and hardware described in this manual are intended to provide general guidelines and instructions for installing the WeatherBug High Definition Motion Camera (HD MotionCam) system. Each installation site is unique and each site may require special considerations that are beyond the scope of this manual. Any questions not covered within this manual should be directed to WeatherBug Weather Station Technical Support at (800)624-4205 or email support@aws.com. -
Page 4: Table Of Contents
Routing the Cable ......................17 Outdoor Installation ...................... 18 Indoor connections ......................21 Setting a Static IP Address for the HD MotionCam ............22 Troubleshooting ........................ 25 Maintenance ........................26 Additional Information...................... 27 ... -
Page 5: Thank You
The WeatherBug HD MotionCam captures images of local weather conditions with the advantage of a much higher resolution and the flexibility of changing viewpoints as often as desired. The quality of the images from the WeatherBug HD MotionCam is sure to enhance your weather system. -
Page 6: Safety
Installation must conform to national, state, and local building code requirements with the most stringent guidelines being adhered to. The HD MotionCam should only be installed by someone comfortable with being on a high ladder or rooftop and who is authorized by the site to perform the installation. Roof and ladder safety is crucial! Allow only qualified Electricians to make electrical connections. -
Page 7: Getting Started
4 Spare Screws with Washers Included in 5500 Enclosure for Top of Camera Housing Included in 5500 MotionCam Mounting Arm 8570 100 ft HD MotionCam Power Cable 5512 200 ft Cat 6 Ethernet Cable 8525 HD MotionCam Power Supply 5510... - Page 8 HD MotionCam Installation Manual Outdoor Components HD MotionCam in Housing Camera Support with Clamp, Connector for Camera and Mounting Arm, 3 Rubber Plugs, Enclosure for Top of Housing, and Spare Screws Mounting Arm Install Sealant Cable Ties Indoor Components 100 ft Power Cable...
-
Page 9: Tools Needed
• Socket drivers, designed to be used with a drill, of the size(s) needed to fit the screws intended for use in mounting the HD MotionCam. • Fish Tape to pull cable through wall • Electrical Tape to tape the ends of cables for protection and to hold connectors and cables together. -
Page 10: Site Evaluation
HD MotionCam Installation Manual Site Evaluation All sites will have certain building restrictions. To get the most out of the camera, a location needs to be chosen that will present the least restrictions. The sky, sun, and clouds are important elements in the captured images. A “perfect”... -
Page 11: Installation
By following these preliminary steps you will have the ability to obtain the internal IP address of the HD MotionCam, which you need in order to view the live video transmitted from the HD MotionCam. It is imperative that you install the camera indoors initially in order to guarantee that the camera is working as it should. - Page 12 HD MotionCam Installation Manual 1. Set the dome of the camera on a soft cloth or soft surface while setting up the camera to avoid scratching the clear dome. 2. Plug one end of the 200 ft Ethernet cable into the camera where the black connection is labeled “LAN”.
-
Page 13: Viewing Live Video And Captured Images
THE HD MOTIONCAM ABSOLUTELY MUST BE CONNECTED TO THE SAME SUBNET AS THE COMPUTER USED TO AQUIRE THE INTERNAL IP ADDRESS OF THE CAMERA. 1. To begin, visit http://download.aws.com. Click on the link that says “HD MotionCam Finder Tool” Release 1, Version 1.0... - Page 14 HD MotionCam Installation Manual 2. Select RUN and follow the steps as prompted to finish installation of the SNC Toolbox. 3. Once FINISH is clicked in the installation wizard, go to the start menu and open the SNC Toolbox application.
- Page 15 Static IP address. Please refer to the section titled, “Setting a Static IP Address for your HD MotionCam” on page 22. 5. Double click the address to pull up the configuration and operation controls for the camera.
-
Page 16: Captured Images
Now that captured images and live video are visible from the HD MotionCam and available on the network, the rest of the installation may be completed. Release 1, Version 1.0... -
Page 17: Routing The Cable
It is best to work with a team of at least two people, as cable will have to be handled from both the inside and the outside of the building. Keep in mind the standard HD MotionCam package contains 100 feet of power cable and 200 feet of Ethernet cable. These cables must reach from the camera to the corresponding network and power connections. -
Page 18: Outdoor Installation
Outdoor Installation For the following steps, the items listed below will be needed: • Mounting Arm • Install Sealant • HD MotionCam in Housing • Camera Support and Clamp • Connector for Camera to Mounting Arm • 3 Rubber Plugs •... - Page 19 HD MotionCam Installation Manual 4. With the top of the camera housing in hand, connect the Power and Ethernet Cables from the Mounting Arm opening to the top of the camera. 5. Feed the attached cables into the mounting arm and line up the two screws with the two openings on the connector.
- Page 20 11. Use the supplied cable ties to clean up any loose cables (if applicable). Cut off the remaining ends of the cable ties. 12. The HD MotionCam needs to be grounded according to local electrical code. Release 1, Version 1.0...
-
Page 21: Indoor Connections
Station Technical Support at 800-624-4205, the camera is fully operational. If the camera requires a static IP address, adjust the camera settings by following the steps in the following section entitled, “Setting a Static IP Address for the HD MotionCam.” Release 1, Version 1.0... -
Page 22: Setting A Static Ip Address For The Hd Motioncam
Setting a Static IP Address for the HD MotionCam (Optional) If the internal IP address of the HD MotionCam is not known, please refer to the Live Video section of Viewing Live Video and Captured Images. Once the SNC Toolbox is downloaded, configure the IP address as shown below as long as the camera is directly connected to the computer through a switch. - Page 23 HD MotionCam Installation Manual 2. A window will pop-up prompting the entry of a User Name and Password. The camera has been programmed with a generic user name and password. The user name is admin and the password is WxBugHD. The password is case sensitive.
- Page 24 HD MotionCam Installation Manual 4. Near the middle of the window, click the radio button labeled “Use the following IP address.” Enter the static IP information in the three boxes below, circled here, and then click OK on the bottom of the page to save.
-
Page 25: Troubleshooting
Address for Your HD MotionCam.” Power Issues In cases of malfunction, the most common cause is lack of power to the HD MotionCam. Be sure to check power supplies and connections to ensure that the HD MotionCam has the proper power supply and that the components are turned on. When the camera is powered on, the booting process and movement of camera is audible when standing directly next to the unit. -
Page 26: Maintenance
4205 or email support@aws.com. Maintenance There is little maintenance needed for the HD MotionCam. As long as the camera housing remains tightly closed and the three rubber plugs are in place, there should rarely be a need to clean anything inside the camera top enclosure. -
Page 27: Additional Information
HD MotionCam Installation Manual Additional Information This product has been designed with safety in mind. However, if not properly installed and used, any electrical product can cause fires. To avoid such incidents, please be sure to follow these guidelines. • Be sure to follow all general safety precautions. -
Page 28: Specifications
HD MotionCam Installation Manual Specifications Item Specification Frame Transfer Up to 30 frames per second (FPS) Electronic Shutter Speed ½ to 1/10,000 s Lens Type Auto-focus zoom lens Zoom Ratio Horizontal Viewing Angle 5.4 to 50 degrees Focal Length F=5.1 to 51mm...