Table of Contents
Advertisement
Quick Links
Operating instruction
Precision/ compact balances and
platform scales
KERN 572/573/KB/DS/FKB/FCB/PCB
Version 5.3
01/2008
GB
KERN & Sohn GmbH
Ziegelei 1
D-72336 Balingen
E-Mail: info@kern-sohn.com
572/573/KB/DS/FKB/FCB/PCB-BA-cz-0853
Tel: +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.kern-sohn.com
Advertisement
Table of Contents
Related Manuals for KERN 572-30
Summary of Contents for KERN 572-30
-
Page 1: Operating Instruction
KERN & Sohn GmbH Ziegelei 1 Tel: +49-[0]7433- 9933-0 D-72336 Balingen Fax: +49-[0]7433-9933-149 E-Mail: info@kern-sohn.com Internet: www.kern-sohn.com Operating instruction Precision/ compact balances and platform scales KERN 572/573/KB/DS/FKB/FCB/PCB Version 5.3 01/2008 572/573/KB/DS/FKB/FCB/PCB-BA-cz-0853... -
Page 2: Table Of Contents
Unpacking __________________________________________________________ 13 6.2.1 Installation ________________________________________________________________ 13 Mains supply ________________________________________________________ 13 Connecting peripheral equipment _______________________________________ 13 Initial start-up________________________________________________________ 13 Adjustment__________________________________________________________ 13 Adjusting (go to 7.2.6)_________________________________________________ 13 6.7.1 Adjusting for verification (KERN 573) ___________________________________________ 14 Verification__________________________________________________________ 14 Operation _________________________________________________________ 15 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853... - Page 3 Display control panel _________________________________________________ 15 Operation ___________________________________________________________ 16 7.2.1 Weighing with Tare _________________________________________________________ 16 7.2.2 Count – Selection Preference Piece ____________________________________________ 16 7.2.3 Percent % ________________________________________________________________ 16 7.2.4 Formula Weighing __________________________________________________________ 16 7.2.5 Tolerance Weighing_________________________________________________________ 16 7.2.6 Adjust____________________________________________________________________ 18 7.2.7 Preselect Tare _____________________________________________________________ 18 7.2.8 Auto Tare _________________________________________________________________ 18...
-
Page 4: Mode - Menue
1 MODE - MENUE 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853... -
Page 5: Technical Data
2 Technical data 2.1 KERN 572 KERN 572-30 572-31 572-32 572-33 572-35 Readability (d) 0.001 g 0.001 g 0.001 g 0.01 g 0.01 g Weighing range (max) 161 g 241 g 301 g 1610 g 2410 g Taring range (subtractive) -
Page 6: Kern 573
2.2 KERN 573 KERN 573-46 Accuracy class Readability (d) 0.1 g Verification value (e) Weighing range (max) 6500 g Minimum load (Min) Taring range (subtractive) 6500 g Reproducibility 0.1 g Linearity ±0.2 g Smallest piece weight 0.3 g Recommended adjusting weight F2 (not supplied) -
Page 7: Kern Kb
2.3 KERN KB KERN KB 120-3 KB 200-3 KB 1200-2 KB 2000-2 KB 10000-1 Readability (d) 0.001 g 0.001 g 0.01 g 0.01 g 0.1 g Weighing range (max) 121 g 201 g 1210 g 2010 g 10100 g Taring range (subtractive) -
Page 8: Kern Ds
2.5 KERN DS KERN DS 5K0.05S DS 8K0.05 DS 10K0.1S DS 16K0.1 DS 20K0.1 Readability (d) 0.05 g 0.05 g 0.1 g 0.1 g 0.2 g Weighing range (max) 5100 g 8100 g 10100 g 16100 g 20100 g Taring range (subtrac-... -
Page 9: Kern Pcb
2.6 KERN PCB KERN PCB 200-3B PCB 240-3B PCB 2000-2B PCB 2400-2B PCB 10K0.05B Readability (d) 0.001 g 0.001 g 0.01 g 0.01 g 0.05 g Weighing range (max) 201 g 241 g 2010 g 2410 g 10.100 g Taring range (subtrac-... -
Page 10: Kern Fcb
2.7 KERN FCB KERN FCB 12K0.1B FCB 24K0.2B Readability (d) 0.1 g 0.2 g Weighing range (max) 12100 g 24100 g Taring range (subtrac- 12100 g 24100 g tive) Reproducibility 0.1 g 0.2 g Linearity ± 0.3 g 0.6 g Smallest piece weight 0.1 g... -
Page 11: Guarantee
For this purpose, the answerable user must define a suit- able interval as well as the nature and scope of this check. Information is available on KERN’s home page (www.kern-sohn.com) with regard to the monitoring of balance test substances and the test weights required for this. -
Page 12: Fundamental Safety Information
Observe the information in the operating instructions Please read the operating instructions carefully before erecting and commissioning, even if you already have experience with KERN balances. Staff training The device may only be operated and looked after by trained members of staff. -
Page 13: Unpacking
Electric power supply is by means of the external mains supply circuit. The printed voltage level must comply with the local voltage. Only use original KERN mains supply circuits. The use of other makes is subject to approval by Kern. Connecting peripheral equipment The balance must be disconnected from the mains before connecting or disconnecting additional equipment (printer, PC) to or from the data interface. -
Page 14: Adjusting For Verification (Kern 573)
6.7.1 Adjusting for verification (KERN 573) General Information: Prior to the procedure of verification the balance has to be adjusted. Remark: The adjusting is only possible when not being blocked by the adjusting switch. The switch for this step is located at the bottom of the housing between the two turning feet. -
Page 15: Operation
7 Operation 7.1 Display control panel Keyboard ON / OFF Print weighing result in MODE: No / descending in % and counting mode: Form reference in MODE: Yes / ascending MODE configuration (see mode structure diagram page 2) Formula weighing in MODE: to left Change g-pieces Unit changeover... -
Page 16: Operation
7.2 Operation 7.2.1 Weighing with Tare 7.2.2 Count – Selection Preference Piece 7.2.3 Percent % 7.2.4 Formula Weighing 7.2.5 Tolerance Weighing 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853... - Page 17 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853...
-
Page 18: Adjust
7.2.6 Adjust 7.2.7 Preselect Tare 7.2.8 Auto Tare 7.2.9 Speed 7.2.10 Auto Off 7.2.11 Variable Factor 7.2.12 Preselect Unit 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853... - Page 19 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853...
-
Page 20: Display Background Illumination
Baud rate adjustable to 2400, 4800 and 9600 baud (default), 19200 baud Sup-D- 9 pol. is necessary . When working with an interface correct operation is secured only if the corresponding KERN-interface- cable (max. 2m) is used. Description of the jack Sup-D- 9 pol. -
Page 21: Rs 232 C Data Output Via Interface Rs 232 C
7.4 RS 232 C Data output via interface RS 232 C RS 232 C Data output via interface RS 232 C General information As a condition for the data transfer between the balance and a peripheral device (for instance printer, PC ...) both devise have to be set on the same interface parameter (for instance baud rate, parity ...). -
Page 22: Printer
7.5 Printer With the serial data output RS 232 a printer can be connected. The printout shows the weight in grams. When the counting mode is selected the number of pieces or the weight is printed. When the percent mode is selected, the percentage or the weight will be printed. Press The PRINT-key to print weighing results. -
Page 23: Maintenance, Upkeep, Disposal
Loose sample residue/powder can be removed carefully using a brush or hand vacuum cleaner. Remove any spilt material to be weighed immediately. 8.2 Maintenance, upkeep The device may only be opened by trained service engineers authorised by KERN. Disconnect from the mains supply before opening. 8.3 Disposal The operating company shall dispose of the packaging and the device in compliance with the valid national or regional law of the operating location. -
Page 24: Declaration Of Conformity
89/336/EEC EMC EN 61326: 1997+ A1:1998+ A2:2001 + A3:2003 EN 61000-3-2: 2000 EN 61000-3-3: 1995 + A1: 2001 Date: 07.01.2008 Signature: Gottl. KERN & Sohn GmbH Management Gottl. KERN & Sohn GmbH, Ziegelei 1, D-72336 Balingen, Tel. +49-[0]7433/9933-0,Fax +49-[0]7433/9933-149 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853... - Page 25 соответствии соответствует перечисленным ниже нормам. Electronic Balance: KERN 573 Mark applied EU Directive Standards 89/336EEC EMC EN45501 EN55022 Date: 03.06.2004 Signature: Gottl. KERN & Sohn GmbH Management Gottl. KERN & Sohn GmbH, Ziegelei 1, D-72336 Balingen, Tel. +49-[0]7433/9933-0,Fax +49-[0]7433/9933-149 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853...
- Page 26 совместно с удостоверением соответствия названной лаборатории. Electronic Balance: KERN 573 EU Directive Standards EC-type-approval certificate no. Issued by 90/384/EEC EN45501 D04-09-019 Date: 03.06.2004 Signature: Gottl. KERN & Sohn GmbH Management Gottl. KERN & Sohn GmbH, Ziegelei 1, D-72336 Balingen, Tel. +49-[0]7433/9933-0,Fax +49-[0]7433/9933-149 572/573/KB/DS/FKB/FCB/PCB-BA-e-0853...
Need help?
Do you have a question about the 572-30 and is the answer not in the manual?
Questions and answers