Applied Engineering Vulcan IIGS User Manual page 26

•
CP/ M
Vulcan can be partitioned to run
If 's vcrs
ion of the CP/ M
Operating syslem, CP/ AM CP/ AM software is included
with
t~
Z-80 Plus and Z.aoc cards. TIle follOWing
is
.:.m
ilbb~l3 ted, S(~by·step
guide to setli ng up a CP/ M !
partitIOn. 1be IIlSinlctiQM il.S.Sl.Jme thil t your Vulcan is
either insblled in
or p6CucJo.sloot:d
to Slot
7
and that your
5.25"
Vulcan UtiliI,)' disk i.s In Slot
6,
Drive
1.
]f you
h~ ve
your system configure d ifferently, modify thc steps
accOrdi ngly.
I) lloot thc Vulcan and run the I'"nition Ma nagcr.
( Refer to Chaptcr 3 for Instructions on running
f'lI n ition Manager).
2) Choose "MO DI FY" from the I'artillon Manager
~, .
3)
Set up the number of pannion(.s) you W<lnt for
Q>/ M! and
!Urn
the panition(s) on, You ClIn turn
on u p to.!l2luCP/ M , panitiQM ilt a time.
4)
Set the boot sm to the CP/ M ! partition from
which you want to
boot
5)
Quit the PartJliOn Manager.
You
don 't
need
to
Formal the p a rtitions YCt
6) Enter the Control Pa
nel and set the Z-80 ClIrd'S slot
to
"Your C3rd '
If It is not al ready
SCI.
7) UooI
into the CP/AM system (disk In Slot 6).
8)
Ru n the
1 'C.COM
program
9) Prcss ' A" to select Add I)cvices.
10) f>rcss"7 " to registcr the Vulcan Slot
Ii) 1 'teS$ "S ' to install Vulcan
:IS
the (0: ) drivc
12) PteS$
"5-
to set
the last
""lid device
13) Press'S" to select Vulcan
:IS
the last valid device.
14) Press Return to s,ave the configuration
15) !'reM ' Y" .
16) Press Return. You should be atlhe (A:) prompt.
]7)
Type
' PI
P A: ~ S, ' " _. this ooplcs ~lIlhe nics from
lhe A drive to the B drive.
18) Ru n the PC.COM program as§lln
]9) Change the
specified
A drive to be the Vulcan,
20)
Change the speciflcd S drivc to be the
5.25"
drive .
Ma ke sure to follow the prompts and
!i:I\'C.'
the
oonfigur.nion
21) Go
back
10
l'roOOS. cnter the Control Panel, and
set
S\oI: 7 (dIC
Vulcan 's sial) as the boot slot:.
22) Reboot the
5~tem
After followi ng these steps the first time , yoo ClIn run
CP/ AM a nytime by using the Vulcan CDA to selcct the
CP/ M' partition
as
the
boot partition and then
rebootirtg.
Refer to AppendIx
B
rOr Vulcan CDA instructions.
Pascal
.eo
Note.'
You
must
USC
Pascal
1.3
with the Vulcan and
the
controller card must
be in slot 4, 5, or 6 with
pseudo-slotting disabled
Once )'OU've .set up and rormatted your Pascal partitiOns
and ha vc one or two turned
ON
( :IS
described 10 the
previous (lu pter), the partition is ready
10
usc.
Copy to It
from yoor P:a.scal disks
u
you would to a floppy. Be sure
to copy the necessary system files
10
the boot partition
Kc:.'t:p In mind that Pa:sc:llhas
a
maximum flIe limit of
n
flies .
Ch. • •
I' I OOOS"
DOS 3.3.
PQcal,
ana
CP/M