Do you have a question about the HydroPower 10H and is the answer not in the manual?
Questions and answers
Peter R Wise
March 29, 2025
How to change temperature
1 comments:
Mr. Anderson
March 29, 2025
To change the temperature on a Bosch HydroPower 10H, adjust the water flow:
- Turn the water flow adjustment anti-clockwise to increase water flow, which lowers the temperature. - Turn it clockwise to decrease water flow, which increases the temperature.
This answer is automatically generated
Brian
January 20, 2025
Hot water drops out when cold is turned on
1 comments:
Mr. Anderson
February 4, 2025
Hot water may drop out when cold water is turned on in a Bosch HydroPower 10H because the water flow through the heater decreases, reducing its ability to maintain the required flow rate to heat the water effectively. This can cause the water temperature to drop or the heater to shut off if the flow rate falls below the minimum operating threshold.
Aquastar automatic instantaneous type water heaters for use with natural and liquefied petroleum gas installation and operating instructions 125b lps, 125b ngs (24 pages)
Page 1
Local Water,Building and Gas fitting regulations Failure to install this appliance in accordance with these installation instructions may void warranty In the interest of continued product improvement, Bosch reserves the right to alter these specifications without notice Service Department: 1300 30 70 42...
Congratulations Congratulations for choosing a Bosch HydroPower water heater. This appliance should give many years of trouble free use, when installed to the specifications contained in this document. The Bosch Story Bosch Thermotechnology has year, Bosch provide hot Extensive research...
Operating Instructions Purge all water and gas pipes before operating. Adjust appliance with only one tap operating. Starting and shutting off the appliance To switch the appliance on, turn the on/off switch to position "1" To shut off the appliance, turn the on/off switch to position "0" Green light on = Main burner on Green light off = Main burner off Red light flashing: Fault Indication...
Page 6
Water Flow Adjustment Turn anti-clockwise Water flow increases, temperature diminishes Turn clockwise Water flow decreases, temperature increases. Warning If the appliance does not operate, burns with yellow flame, leaks water or a gas smell is evident, turn off and contact the local gas authority, the manufacturer or an authorised service person.
Trouble Shooting Symptom Possible Cause Solution Appliance does not light Switch turned off Turn switch on Hydrogenerator Jammed Clean hydrogenerator Low Water Flow Increase water flow >3.2 litres per minute Smell of gas Gas Leak Locate leak with soap solution Low burner flame, water Low inlet gas pressure Check supply regulator &...
10 Basic Steps for Installation Check cold water supply pressures, min & max as per table below. Model BOSCH 10H BOSCH 13H BOSCH 16H Minimum Inlet Pressure for 60 kPa 100 kPa 130 kPa maximum water flow Minimum Inlet Pressure for...
Page 9
Turn adjustment screw (Position C in picture below) located on left hand side of gas valve at a 45° angle to correct pressure. Anti clockwise to decrease minimum burner pressure. Model BOSCH 10H BOSCH 13H BOSCH 16H Burner Pressure LPG 0.64 kPa...
Regs Chart APPLIANCE LOCATION This water heater is approved for outdoor installation only. Do not install this water heater with any modification or alteration. Do not install this water heater indoors or in an enclosed space . WARNING: FLUE OUTLET MUST BE FREE FROM ANY COMBUSTIBLE MATERIAL. CLEARANCES FOR FLUE TERMINAL (front of heater) The location of the flue terminal must comply with the clearances shown on this page.
The warranty period commences from the purchase date. Claims for warranty will only be accepted upon suitable proof of purchase submitted to Robert Bosch (Australia) Pty. Ltd. Or an approved Bosch Service Agent authorised to carry out warranty repairs.
Bosch & the Environment Environmental sustainability is of prime importance to Bosch. This focus is essential from design and production, through to recommending the correct sized appliance for the consumer’s daily hot water requirements.
Need help?
Do you have a question about the HydroPower 10H and is the answer not in the manual?
Questions and answers
How to change temperature
To change the temperature on a Bosch HydroPower 10H, adjust the water flow:
- Turn the water flow adjustment anti-clockwise to increase water flow, which lowers the temperature.
- Turn it clockwise to decrease water flow, which increases the temperature.
This answer is automatically generated
Hot water drops out when cold is turned on
Hot water may drop out when cold water is turned on in a Bosch HydroPower 10H because the water flow through the heater decreases, reducing its ability to maintain the required flow rate to heat the water effectively. This can cause the water temperature to drop or the heater to shut off if the flow rate falls below the minimum operating threshold.
This answer is automatically generated