Table of Contents
Advertisement
Quick Links
Installation and Owner's Manual
A barrier designed to reduce the burn hazard from the
glass viewing area is provided with this appliance and
shall be installed.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury or loss of life.
Do not store or use gasoline or other
fl ammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light the appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fi re department.
Installation and service must be performed
by a qualifi ed installer, service agency or the
gas supplier.
4003166-03
©2012, Miles Industries Ltd.
L
EGEND
Direct Vent Gas Insert
700IN (NG) & 700IP (LPG)
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
Manufactured by
MILES INDUSTRIES LTD., British Columbia, Canada
www.valorfi replaces.com
G3.5
Lea ve t his ma nua l
with t he applianc e.
C O NSU ME R
Re tain t his manua l
for f uture ref e re nce.
Please read this manual
BEFORE installing and operating
this appliance.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certifi ed kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Massachusetts: The piping and fi nal
gas connection must be performed by a
licensed plumber or gas fi tter in the State of
Massachusetts.
Ce guide est disponible en français sur demande.
Patent Pending
I NSTALLER
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Miles Industries Valor LEGEND G3.5 700IN
Summary of Contents for Miles Industries Valor LEGEND G3.5 700IN
- Page 1 Installation and service must be performed Ce guide est disponible en français sur demande. by a qualifi ed installer, service agency or the gas supplier. Manufactured by MILES INDUSTRIES LTD., British Columbia, Canada www.valorfi replaces.com 4003166-03 ©2012, Miles Industries Ltd.
-
Page 2: Table Of Contents
Ceramic Rocks Installation ......31 The information contained in this installation manual is believed to be correct at the time of printing. Miles Industries Ltd. reserves the right to change or modify any information or speci- fi cations without notice. Miles Industries Ltd. -
Page 3: Safety Precautions
Safety Precautions READ and UNDERSTAND all instructions carefully This unit MUST be used with a vent system as before starting the installation. FAILURE TO FOLLOW described in this installation manual. NO OTHER vent these installation instructions may result in possible fi re system or components MAY BE USED. -
Page 4: Safety And Your Fireplace
Safety and Your Fireplace Safety and Your Fireplace Please Read and Carefully Follow all Safety Warnings and Operating Instructions Contained in Your Owners Manual (Replacement Manuals are available by contacting our service department at 1-800-468-2567 or visit www.valorfi replaces.com). withdraw in the event of accidental Please Follow These Important contact with a hot surface. -
Page 5: Owner's Information
Owner’s Information INFORMATION Thank You ... WARNING For purchasing a Valor by Miles Industries. Your new EXTREMELY HOT!!! radiant gas heater is a technical appliance that must be installed by a qualifi ed dealer. Each Valor fi replace • READ the SAFETY information on pages... - Page 6 3. Find the levers on each results in your particular case. side of the window towards NOTE: This is a problem beyond Miles Industries’ the top. Using your fi nger, control and is not covered under warranty. pull the levers towards you •...
- Page 7 OWNER’S Owner’s Information INFORMATION 3. While you hold it, unhook the side levers from the trim Checks supports and hook them into the window tabs. A periodic check of the pilot and burner fl ames should be made. Check after the fi re has been on for at least 30 minutes.
- Page 8 OWNER’S Owner’s Information INFORMATION The appliance area must always be kept clear and Batteries free from combustible materials, gasoline and other WARNING fl ammable vapors and liquids. Inspect the vent terminal outdoors regularly to make DO NOT ATTEMPT TO CHANGE THE BATTER- IES WHILE THE FIREPLACE IS STILL HOT! Let sure that snow, trees, bushes, leaves, or other objects the fi...
- Page 9 OWNER’S Owner’s Information INFORMATION (including pilot) Lighting, Operation and Rating Information How to Turn Your Fireplace OFF Familiarize yourself with each of these methods before WARNING operating your fi replace. DO NOT ATTEMPT TO TOUCH THE DATA PLATE Handset and Wall Switch: Press and hold the OFF WHILE THE FIREPLACE IS STILL HOT! Let the button for a second.
-
Page 10: Remote Control Operation
OWNER’S Remote Control Operation INFORMATION NOTE: Before using the remote control system for IMPORTANT: BEFORE YOU BEGIN, please note that the fi rst time, the receiver and the handset must be on this system, the settings of time, temperature and synchronized. - Page 11 OWNER’S Remote Control Operation INFORMATION • Press and hold (small fl ame) MODES OF OPERATION button to decrease fl ame height or • Briefl y pressing the SET button to set the appliance at pilot fl ame. changes the mode of operation in •...
- Page 12 OWNER’S Remote Control Operation INFORMATION • SETTING THE ON / OFF TEMPERATURES - Nighttime Setback T E M P Temperature Mode (Appliance must be in standby mode; pilot SETTING THE “DAYTIME” TEMPERATURE ignited) - The room temperature (sun), 23ºC / 74ºF Default Settings: TEMP is measured and compared to the...
- Page 13 OWNER’S Remote Control Operation INFORMATION SETTING THE “NIGHTTIME SETBACK” SETTING PROGRAM TIMERS TEMPERATURE • You can program two periods of time between 12:00 (moon), “ Default Settings: ” (OFF) T E M P am and 11:50 pm in each 24-hour cycle. •...
- Page 14 OWNER’S Remote Control Operation INFORMATION SETTING P1 OFF TIME SETTING P2 ON TIME • Briefl y press SET to scroll to TIMER mode • Briefl y press SET button to scroll (sun) while the time fl ashes. to TIMER (moon) while the •...
-
Page 15: Options
OWNER’S Remote Control Operation INFORMATION LOW BATTERY INDICATION HANDSET / RECEIVER MATCH The remote control handset and receiver are program- CAUTION med to function together. In case of a replacement of DO NOT USE a screwdriver or other metallic object the handset or the receiver, you will need to reset the to remove the batteries from the battery box or the receiver to allow them to function together. -
Page 16: Lighting Instructions
OWNER’S Lighting Instructions INFORMATION FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING : If you do not follow these instructions exactly A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly. To save gas, turn the pilot off when not using the appliance for a prolonged period of time. -
Page 17: Installation Planning
QUALIFIED Installation Planning INSTALLER Installer—READ THIS FIRST See the Installer’s Checklist provided with the appliance Only qualifi ed licensed or trained personnel for installation steps. The checklist is on the reverse side should install this appliance. of the content list for the appliance packaging. Specifi... -
Page 18: Overview
QUALIFIED Overview INSTALLER This appliance may ONLY be installed in an existing unaltered, functioning solid-fuel burning fi replace with a working fl ue and constructed of non-combustible material. DO NOT install into combustible construction. This appliance is NOT APPROVED for installation with a zero clearance kit. WARNING Chimney Terminal Cap Some materials or items, although... -
Page 19: Dimensions
QUALIFIED Dimensions INSTALLER 28-5/8” (727 mm) 21-1/4” (540 mm) Fan box: 6’ (1.8 m) Fan power cord 3” (76 mm) Optional fan 3” 3” 9” (76 mm) (76 mm) 13” (228 mm) (330 mm) 13” 4” Trim (102 mm) (102 mm) (sold separately) 10”... -
Page 20: Clearances
QUALIFIED Clearances INSTALLER WARNING Some materials or items, although safe, may discolor, shrink, warp, crack, peel, Some materials or items, although safe, may discolor, shrink, warp, crack, peel, and so on because of the heat produced by the fi replace. Avoid placing candles, and so on because of the heat produced by the fi... -
Page 21: Venting
QUALIFIED Venting INSTALLER Typical Vent Installation See the Approved Venting Accessories list on page 39 of this manual. NOTE: Flexible co-linear vent pipes may only be installed into existing non-combustible solid-fuel burning fi replaces and chimneys. Terminal Cap Vent Location The vent terminal must be located above the roof. -
Page 22: Existing Fireplace Preparation
QUALIFIED Existing Fireplace Preparation INSTALLER A few points must be considered before inserting the Gas Line Routing 700 into an existing fi replace cavity. Generally, no Plan the routing of the gas line before proceeding. modifi cations are allowed to the existing fi replace that Utilize the existing hole for the gas line of the factory- will compromise the integrity of the existing fi... - Page 23 QUALIFIED Appliance Preparation INSTALLER Window Removal The window is held in place by a spring-loaded lever on each side. 1. To remove the window, locate the levers on each side of the window towards the top. Using your fi nger, pull the lever towards you and unhook it from the window frame bracket.
- Page 24 QUALIFIED Appliance Preparation INSTALLER Venting Installation IMPORTANT: This appliance’s venting system is room sealed and there- fore, does not require room air to be used in the combustion process. 1. Rough-in two 3” diameter vent liners into the existing chimney system from the roof.
-
Page 25: Supply Gas Installation
QUALIFIED Supply Gas Installation INSTALLER The gas supply inlet connection is a 1/2” NPT female. A The appliance must be isolated from the gas supply gas shut-off valve is supplied on the end of a stainless piping system by closing its equipment shut-off valve steel fl... - Page 26 QUALIFIED Supply Gas Installation INSTALLER 2. Install alternate elbow (not supplied). Inlet Connection The appliance is sup- plied with a fl ared elbow 6-3/8” (162 mm) connector fi tted onto the 3/8” street elbow(s) valve and a fl ex connec- (where allowed) tor supplied loose to be attached to the elbow...
-
Page 27: Ceramic Panels Installation
QUALIFIED Ceramic Panels Installation INSTALLER The following guidelines apply for all liner panels 5. Rotate the anchor up and out of the way and slide (supplied separately). the left hand side panel against the fi rebox side. Rotate the anchor back down to hold the panel. 1. -
Page 28: Ceramic Logs Installation
QUALIFIED Ceramic Panels Installation INSTALLER 11. With logs only: Install the front bricks in front of the 9. Reinstall the front brick support. burner. 10. Reinstall the rear log support (3 screws). Its rear 12. With logs only: Slide the cast iron grate in the edge rests on the rear brick support ledge. - Page 29 QUALIFIED Ceramic Logs Installation INSTALLER 2. Place the black glass piece on top of the burner and 4. Place the right front log with its left end fl at on the move it forward to rest in the grooved recess of the glass.
- Page 30 QUALIFIED Ceramic Logs Installation INSTALLER 6. Isntall the top right log. Place its wider end on the front right log’s peg and rest its narrow end in the notch on the rear log. 7. If desired, add loose embers on top of the front bricks between the legs of the grate in the shaded space.
-
Page 31: Ceramic Rocks Installation
QUALIFIED Ceramic Rocks Installation INSTALLER For ceramic logs, see previous section. Unpack the ceramic rocks very carefully to avoid damaging them. Install the rocks as shown. Please note that the position of some of the rocks identifi ed in the following instructions is critical to ensure proper performance of the appliance. - Page 32 QUALIFIED Ceramic Rocks Installation INSTALLER 5. Identify rocks number 1, 2, 3, 4 and 5. These rocks 8. Identify the rocks 7, 9, 11 and 14. These rocks have pegs that fi t in the holes on top of the rock have one hole underneath and fi...
-
Page 33: Side Shrouds Installation
QUALIFIED Ceramic Rocks Installation INSTALLER 11. Optional: Lay the twigs on the rocks. They can be IMPORTANT: The rocks of the top row (14, 11, 9 placed as suggested below or elsewhere on the and 7) overhang slightly over the burner. rocks as long as they do not block the pilot fl... -
Page 34: Window Refi Tting
QUALIFIED Window Refi tting INSTALLER 1. To facilitate the installation of the window, hook the 3. While you hold it, unhook the side levers from side spring-loaded levers to the side shrouds as the side shrouds and hook them into the window indicated so they are not in the way of the window brackets on each side. -
Page 35: Remote Control Initial Set-Up
QUALIFIED Remote Control Initial Set-up INSTALLER The receiver and the handset of the remote control 5. With a sharp object, press and hold the receiver’s system must be initially synchronized before the fi rst reset button until you hear one short and one long use. -
Page 36: Operation Check & Aeration Settings Adjustment
QUALIFIED Operation Check & Aeration Settings Adjustment INSTALLER In a few unusual installations, the fl ame picture may Operation Check be improved by adjusting the aeration. The need for Turn the fi replace fl ame up and down using the adjustment should be determined only by operating the remote control to confi... -
Page 37: Front And Trim Installation
QUALIFIED Front and Trim Installation INSTALLER Install the front or trim chosen by the consumer following the instructions supplied with the front or trim. Install the barrier screen supplied with the front or trim as per instructions included with the front or trim. -
Page 38: Wiring Diagram
QUALIFIED Wiring Diagram INSTALLER Optional Wall Switch Kit 1265WSK Connector Yellow Optional Fan Remote Control Battery Box Module 4 AA Batteries GV60 MAX Wiring Diagram... -
Page 39: Approved Venting Components
QUALIFIED Approved Venting Components INSTALLER Approved Direct Vent Suppliers for Valor Models 700, 739, 780, 785 and RF24DV Venting Parts Code / availability by Manufacturer Venting Parts Description 4DVC Standard Co-axial 46DVA-VC 4DT-VC TM-4VT — HSDV4658-1313 — 4DH-1313 High Wind Co-axial 46DVA-VCH —... -
Page 40: Warranty
1. Extended Warranty Coverage For a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will at its option pay the initial purchaser for the repair of, or will exchange the following parts or components which are found to be defective in material or... -
Page 41: Spare Parts
OWNER’S Spare Parts INFORMATION Part Part Code Description Code Description Number Number Exhaust slide assembly 4002287 Air shutter slider NG 4002345 Exhaust slide gasket 4001662 Air shutter cover NG 4002346 Restrictor enclosure 4002330 Flashback shield LPG 3000371 Metal strips (2) 4002329 Air shutter slider LPG 320B293... - Page 42 OWNER’S Spare Parts INFORMATION Part Code Description Number Rock no. 18 4002661 LH Twig 4001827 RH Twig 4001828 Enamel platform 4003231EB Platform base 4003230 #8 - 32 Hexagonal nut plated (2) 4001517 Liner panels—complete set Ledgestone 705LSL Enamel black 706EBL Ceramic fl...
- Page 43 OWNER’S Spare Parts INFORMATION 3 - 7 56 - 57 71 72 80, 80a 27 - 31 17 - 23 33a, 33b...
- Page 45 Serial Number: Date Purchase (yyyy-mm-dd): Dealer: Customer Information First Name: Last Name: Contact Information Email: Mailing Address Address: City: Province/State: Postal/Zip Code: Country: Cut out page, fi ll information, and mail to Miles Industries Ltd. Online Warranty registration at www.valorfi replaces.com...
- Page 46 Tape Shut Fold here Postage needed Miles Industries Ltd. 190 - 2255 Dollarton Highway North Vancouver, BC V7H 3B1 Canada Online Warranty registration at www.valorfi replaces.com Thank you for choosing a Valor Product...
Need help?
Do you have a question about the Valor LEGEND G3.5 700IN and is the answer not in the manual?
Questions and answers