Miles Industries Portrait 530INI Owner's Manual

Direct vent gas insert fireplace natural gas propane gas

Advertisement

Quick Links

INSTALLATION & OWNER'S MANUAL
Direct Vent Gas Insert Fireplace
530INI (natural gas) & 530IPI (propane gas)
DANGER
!
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and shall be
installed for the protection of children and other at-risk
individuals.
!
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
— Do not store or use gasoline or other
fl ammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
▪ Do not try to light any appliance.
▪ Do not touch any electrical switch; do
not use any phone in your building.
▪ Leave the building immediately.
▪ Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
▪ If you cannot reach your gas supplier,
call the fi re department.
— Installation and service must be
performed by a qualifi ed installer,
service agency or the gas supplier.
4005323-07
©2018, Miles Industries Ltd. All rights reserved.
Portrait
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
Please read this manual
BEFORE
operating this appliance.
INSTALLER
Leave this manual
with the appliance.
CONSUMER
Retain this manual
for future reference.
This manual contains instructions to install the EN-
GINE ONLY. A front trim kit is REQUIRED to install
the engine as it aff ects the framing cavity and posi-
tion of the engine. A barrier screen is provided with
the front or trim kit. Refer to the manual supplied
with the front for framing and fi nishing.
This appliance may be installed in an after-
market permanently located, manufactured
(mobile) home where not prohibited by local
codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certifi ed kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in
a bedroom or bed sitting room.
Ce guide est disponible en français sur demande.
installing and

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Portrait 530INI and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Miles Industries Portrait 530INI

  • Page 1 — Installation and service must be a bedroom or bed sitting room. performed by a qualifi ed installer, Ce guide est disponible en français sur demande. service agency or the gas supplier. 4005323-07 ©2018, Miles Industries Ltd. All rights reserved.
  • Page 2: Table Of Contents

    Designed and Manufactured by / for Miles Industries Ltd. 190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1 Tel. 604-984-3496 Fax 604-984-0246 www.valorfi replaces.com © Copyright Miles Industries Ltd., 2018. All rights reserved.
  • Page 3: Safety And Your Fireplace

    Safety and Your Fireplace SAFETY AND YOUR FIREPLACE Read and understand all instructions carefully before Do not use this heater as a temporary source of starting the installation. Failure to follow these instal- heat during construction. lation instructions may result in possible fi re hazard and Due to the high temperature, the appliance should be will void the warranty.
  • Page 4 Safety and Your Fireplace Read and carefully follow all safety warnings and operating instructions contained in your owner’s manual Replacement manuals are available by contacting the Valor Service Department at 1-800-468-2567 or visit www.valorfi replaces.com. FOLLOW THESE IMPORTANT CHILD SAFETY PRECAUTIONS AND RECOMMENDATIONS Parts of your Valor Fireplace become extremely hot while in operation.
  • Page 5 SAFETY AND YOUR FIREPLACE This manual and particularly the preceeding and following pages contain very important information regarding the safe operation of your fi replace as well as maintenance instructions. Read carefully before operating your fi replace and pay special attention to the safety warnings. A heating gas appliance does require safe handling.
  • Page 6: Introduction

    INFORMATION Thank You ... Operating Your Fireplace for the First Time For purchasing a Valor by Miles Industries. Your new When operating your new fi replace for the fi rst time, radiant gas heater is a technical appliance that must some vapors may be released due to the burning of be installed by a qualifi...
  • Page 7: Operating Your Fireplace

    OWNER’S Operating Your Fireplace INFORMATION Fireplace Control Devices In the unlikely event that you cannot turn off your fi replace with the remote control handset, use the There are three ways to control your fi replace. wall switch (if installed); if the wall switch malfunctions 1.
  • Page 8: Using The Remote Control

    OWNER’S Using the Remote Control INFORMATION Current temperature Handset (F or C) sensor Period Battery status start or end (Temp, Timer) Current time (12 or 24 hour clock) Current programmed Modes (Manual, period (Timer) Temperature, Timer) Synchronize Remote Control BEFORE YOU BEGIN, please note that on this system, the settings of time, temperature and automatic ON/OFF can only be programmed when the function display is fl...
  • Page 9 OWNER’S Using the Remote Control INFORMATION M A N T E M P TEMP TIMER M A N M A N TEMP T E M P TIMER...
  • Page 10 OWNER’S Using the Remote Control INFORMATION TEMP T E M P TEMP T E M P...
  • Page 11 OWNER’S Using the Remote Control INFORMATION...
  • Page 12 OWNER’S Using the Remote Control INFORMATION...
  • Page 13: Kits & Accessories

    OWNER’S Kits & Accessories INFORMATION Required Kits Information accurate at the time of printing and subject to change without notice. Fuel Beds (choose one) 530LSK Traditional Logs & Reversible Liners Set 530RSK Rocks & Reversible Liners Set 530CSK Coals & Reversible Liners Set 530DWK Driftwood &...
  • Page 14: Lighting Instructions

    OWNER’S Lighting Instructions INFORMATION FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING : If you do not follow these instructions exactly A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly. To save gas, turn the pilot off when not using the appliance for a prolonged period of time.
  • Page 15: Servicing & Maintenance

    OWNER’S Servicing & Maintenance INFORMATION Servicing Your Fireplace We recommend having your fi replace serviced every year. Contact your supplier quoting the model number. It will be helpful if the appliance’s serial number can also be quoted. These numbers are on the information card.
  • Page 16: Cleaning Your Fireplace

    3. Unscrew the two spring-loaded bolts securing the only and are not meant to guarantee results. bottom of the window. NOTE: This is a problem beyond Miles Industries’ control and is not covered under warranty. • Clean the glass regularly as soon as you notice the buildup (white fi...
  • Page 17 OWNER’S Servicing & Maintenance INFORMATION To refi t the window: 4. Pull the top of the window forward and release to ensure the springs return it in position. DANGER 5. Similarly check the bottom of the window by pulling The window unit must be correctly installed, it forward and releasing.
  • Page 18: Checking Pilot And Burner Flames

    OWNER’S Servicing & Maintenance INFORMATION Checking Pilot and Burner Flames The appliance area must always be kept clear and free from combustible materials, gasoline and other A periodic check of the pilot and burner fl ames should fl ammable vapors and liquids. Inspect the vent terminal be made.
  • Page 19: Replacing Batteries

    OWNER’S Servicing & Maintenance INFORMATION Replacing Batteries 2. Slide and remove the receiver cover. 3. Replace batteries with 4 AA alkaline batteries. WARNING 4. Replace the cover. DO NOT ATTEMPT TO CHANGE THE BATTER- 5. Put the receiver back in its position pushing IES WHILE THE FIREPLACE IS STILL HOT! Let it in so it attaches to the Velcro tab.
  • Page 20: Specifi Cations

    QUALIFIED Specifi cations INSTALLER Approvals and Codes Supply Gas This appliance is certifi ed to ANSI Z21.88–2016/CSA Heater engine 530INI is used for natural gas insert 2.33–2016 American National Standard/CSA Standard installations. for Vented Gas Fireplace Heaters for use in Canada Heater engine 530IPI is used for propane gas insert and USA.
  • Page 21: Overview

    QUALIFIED Overview INSTALLER This appliance may ONLY be installed in an existing unaltered, functioning solid-fuel burning fi replace with a working fl ue and constructed of non-combustible material. DO NOT install into combustible construction. This appliance is NOT APPROVED for installation with a zero clearance kit. WARNING WARNING Approved Chimney...
  • Page 22 QUALIFIED Overview INSTALLER Co-Linear—as supplied Venting options Rear view Note: 536/541/563 fronts require a closure plate (582/583CPB) to ensure proper positioning of casting. Other fronts are supplied with a backing plate included. Co-linear appliance, as supplied (2 x 3” diameter liners) 530INI/IPI as supplied 530INI/IPI with 720SWK—Sidewall Kit Co-linear installation into existing F/P...
  • Page 23 QUALIFIED Overview INSTALLER Convert to Co-Axial 530INI/IPI with 530CVA2—Co-axial Appliance Adapter Venting options Co-linear installation into existing F/P Rear view Approved co-axial termination 5 x 3 to 6-5/8 x 4 adapter Discard + approved Add 530CVA2— existing Appliance co-axial 6-5/8 x 4 Flashing vent plate Adapter...
  • Page 24: Dimensions

    QUALIFIED Dimensions INSTALLER 20” 9” - 11-1/2” depending on front trim - see front installation manual Varies with front trim. Varies with front trim. See Front trims installation See Front trims installation manuals for dimensions. manuals for dimensions. 2 x 3” dia. colinear vent (as supplied) 5”x 3”...
  • Page 25: Clearances

    QUALIFIED Clearances INSTALLER WARNING WARNING Some materials or items, although safe, may discolor, shrink, warp, crack, peel, and so on because of the heat produced by the fi replace. Avoid placing candles, paintings, photos, and other items sensitive to heat around the fi replace. Mantel Combustible Mantel Clearances Depth...
  • Page 26: Venting

    QUALIFIED Venting INSTALLER Typical Vent Installation Terminal Cap (co-linear) See the Approved Venting Components list on page 45 Flashing of this manual. Vent Location 2 x 3” fl ex liners—see Venting Table for length The vent terminal must be located through the roof. allowed This direct vent appliance is designed to operate when an undisturbed airfl...
  • Page 27: Attaching Air Restrictors

    QUALIFIED Venting INSTALLER Attaching Air Restrictors Air Restrictor Appliances with more than 10’-0” Vertical Vent Rise Only No restrictors are required for appliances which that have less than 10’-0” vertical run. If installing an appliance which has less than 10’-0” vertical vent pipe rise, ignore this stage.
  • Page 28: Existing Fireplace Preparation

    QUALIFIED Installation Planning INSTALLER Installer—READ THIS FIRST Only qualifi ed licensed or trained personnel 7. Place the appliance in fi nal position. should install this appliance. 8. Install the venting system. 9. Position the restrictors. 1. YOU NEED TO KNOW FROM THE HOMEOWNER: 10.
  • Page 29: Unpack The Appliance

    QUALIFIED Existing Fireplace Preparation INSTALLER Gas Line Routing Combustible Mantels Plan the routing of the gas line before proceeding. Combustible mantel clearances should conform to Utilize the existing hole for the gas line. If the factory- those required for the original solid-fuel fi replace into built fi...
  • Page 30: Remove Window

    QUALIFIED Installation INSTALLER Remove Window 1. Release the top of the window by pulling forward the two levers at the top corners. 2. Unscrew the two spring-loaded bolts securing the bottom of the window. 3. Carefully lift the window. Keep the window and bolts in a safe place.
  • Page 31: Co-Linear Applications (2 - 3" Liners)-Connect Venting

    QUALIFIED Installation INSTALLER Co-Linear Applications (2 - 3” liners)—Connect Venting IMPORTANT: This appliance’s venting system is room sealed and therefore, does not require room air to be used in the combustion process. 1. Rough-in two 3” diameter vent liners into the existing chimney system from the roof.
  • Page 32: Co-Axial Applications (3" X 5" Liners)-Connect Venting

    QUALIFIED Installation INSTALLER Co-Axial Applications (3” x 5” liners)—Connect Venting Approved 4” x 6-5/8” vertical co-axial IMPORTANT: This appliance’s venting system is room sealed and termination therefore, does not require room air to be used in the combustion process. 1. Stretch 3” and 5” liners individually to required length. Insert eh Terminal Adapter 3”...
  • Page 33: Connect Gas Supply

    QUALIFIED Installation INSTALLER Connect Gas Supply • When testing for leaks: • It’s preferable to rough-in the gas line at this point before proceeding with the fi rebox installation. • Make sure that the appliance is turned off . • The appliance is supplied for supply gas connection •...
  • Page 34: Install Ceramic Liners (Logs Or Coals Only)

    QUALIFIED Installation INSTALLER Install Ceramic Liners (Logs or Coals only) The 530LSK and CSK fuel beds include a set of reversible liners. One side shows the brick pattern and the reverse side shows a black vertical fl uted pattern. Follow the instructions below to install the liner set on the chosen side.
  • Page 35: Install The 530Lsk-Traditional Logs Set

    QUALIFIED Installation INSTALLER Install the 530LSK—Traditional Logs Set 5. Locate the left side log on the ceramic pin on the left 1. Place the base log on the supports in the fi rebox hand side of the base log. Rest the narrow nose of and against the support at the fi...
  • Page 36: Install The 530Csk-Coal Set

    QUALIFIED Installation INSTALLER Install the 530CSK—Coal Set 1. Place the base coal on the supports in the fi rebox 4. The center right coal has letter “R” embossed and against the fi rebox back. underneath. Place this coal behind the front right 2.
  • Page 37: Install The 530Rsk-Rock Set And Liners

    QUALIFIED Installation INSTALLER Install the 530RSK—Rock Set and Liners Install rock base & platform 1. Place the rock base behind the burner. The two Unpack each piece of the ceramic rock set carefully to protrusions in front of the base should rest on the avoid damages.
  • Page 38 QUALIFIED Installation INSTALLER Rock Other Position in the Top row rear Description markers fi rebox Top far left 1 peg under Top row rear Top left 1 peg under Top row rear Top right 1 peg under Top row rear Top far right 1 peg under Top row rear...
  • Page 39: Install The 530Dwk-Driftwood Kit And Liners

    QUALIFIED Installation INSTALLER Install the 530DWK—Driftwood Kit and Liners Install platform, driftwood logs and rocks 1. Place the protrusion at the back of the base log on Unpack each piece of the ceramic driftwood set the ledge of the rear panel support as far back as carefully to avoid damages.
  • Page 40 QUALIFIED Installation INSTALLER 3. Place the rear log on top of the base log locating it 6. Place the left log inserting the platform peg into the into the notches on top of the base log. hole at the end of the log; rest the upper end of the log in the notch on the rear log as indicated.
  • Page 41: Refi T And Check Window

    QUALIFIED Installation INSTALLER Refi t and Check Window DANGER 1. Place the window centrally against the engine unit and The window unit must be correctly installed, resting on the support at bottom front of the engine. fastened and sealed after servicing or serious 2.
  • Page 42: Synchronize Remote Control

    QUALIFIED Installation INSTALLER Synchronize Remote Control The receiver and the handset of the remote control sys- tem must be initially synchronized before the fi rst use. 1. Insert alkaline batteries in the remote control receiver and handset. The receiver is located left of the control valve under the burner module.
  • Page 43: Install Front Trim And Barrier Screen

    QUALIFIED Installation INSTALLER Install Front Trim and Barrier Screen Install the front chosen by the customer for the fi replace. Install as well the barrier screen which is provided with the front trim. Show the customer how to access the controls when the front is installed and how to remove the front.
  • Page 44: Wiring Diagram

    QUALIFIED Wiring Diagram INSTALLER Optional Wall Switch Kit 1265WSK Connector Yellow GV60 Wiring Diagram...
  • Page 45: Approved Venting Components

    QUALIFIED Approved Venting Components INSTALLER...
  • Page 46: Warranty

    1. Extended Warranty Coverage For a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will at its option pay the initial owner for the repair of, or will exchange the following parts or components which are found to be defective in material or workmanship...
  • Page 47: Replacement Parts

    OWNER’S Replacement Parts INFORMATION Description Part no. Description Part no. Side wall support (2) 330A898 Handset G6R H3T5-ZV (BJ) 4001910 Rear wall support 320B320 Wall mount holder 9000008 Velcro strip 4000022 Wiring harness 4001187 Port cover 4000828AH Hot glass warning plate 4003093 Exhaust slide assembly 4005299...
  • Page 48 OWNER’S Replacement Parts INFORMATION Description Part no. Driftwood Kit 530DWK Log Set (including pebbles) 4005603 Base log 4005887 Rear log 4005888 Left log 4005889 Right log 4005890 Centre log 4005891 Brown beach pebble 4003082 Small grey beach pebble 4003086 Grey beach pebble 4003083 Small beige beach pebble 4003087...
  • Page 49 OWNER’S Replacement Parts INFORMATION Natural gas Propane gas 33a, 33b 530CSK 530LSK...
  • Page 50 OWNER’S Replacement Parts INFORMATION 530RSK 530DWK...
  • Page 51 Serial Number: Date Purchase (yyyy-mm-dd): Dealer: Customer Information First Name: Last Name: Contact Information Email: Mailing Address Address: City: Province/State: Postal/Zip Code: Country: Cut out page, fi ll information, and mail to Miles Industries Ltd. Online Warranty registration at www.valorfi replaces.com...
  • Page 52 Tape Shut Fold here Postage needed Miles Industries Ltd. 190 - 2255 Dollarton Highway North Vancouver, BC V7H 3B1 Canada Online Warranty registration at www.valorfi replaces.com Thank you for choosing a Valor Product...

This manual is also suitable for:

Portrait 530ipi

Table of Contents