Related Manuals for ESAB Origo M11 Feed 302
Summary of Contents for ESAB Origo M11 Feed 302
- Page 1 Origot M11 Feed 302 Instruction manual 0459 206 101 GB 090325 Valid for serial no. 620- -xxx- -xxxx...
-
Page 2: Table Of Contents
1 DIRECTIVE ............2 SAFETY . -
Page 3: Directive
DIRECTIVE DECLARATION OF CONFORMITY ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, declares that Wire feed unit Feed 302 from serial number 620 onwards, conforms to standard IEC/EN 60974--5, in accordance with the re- quirements of directive (73/23/EEC) and appendix (93/68/EEC) and standard IEC/EN 60974--10 in accordance with the requirements of directive (89/336/EEC) and appendix (93/68/EEC). - Page 4 MALFUNCTION - Call for expert assistance in the event of malfunction. Read and understand the instruction manual before installing or operating. PROTECT YOURSELF AND OTHERS! ESAB can provide you with all necessary welding protection and accessories. CAUTION! Read and understand the instruction manual before installing or operating.
-
Page 5: Introduction
The wire feed unit can be installed either at the power source, suspended above the workplace, on a support arm or on the floor with or without wheel set. ESAB’s accessories for the product can be found on page 16. Equipment... -
Page 6: Installation
Duty cycle The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer- tain load without overloading. The duty cycle is valid for 40˚C. Enclosure class The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid objects or water. -
Page 7: Operation
OPERATION General safety regulations for the handling of the equipment can be found on page 3. Read through before you start using the equipment! WARNING! Assure that the side panels are closed during operation. WARNING! To prevent the reel from sliding off the hub: Lock the reel in place by turning the red knob as shown on the warning label attached next to the hub. -
Page 8: Connections And Control Devices
“ELP/0”. The wire feed unit with water connection is equipped with a detection system ELP (ESAB Logic Pump) which checks that the water hoses are connected. When connecting a water--cooled welding gun, the water pump starts. Detection only works with power sources that are equipped with ELP. -
Page 9: Function Explanations
Function explanations Burnback time Burnback time is a delay between the time when the wire starts to brake until the time when the power source switches off the welding voltage. Too short burnback time results in a long wire stickout after completion of welding, with a risk of the wire being caught in the solidifying weld pool. -
Page 10: Wire Feed Pressure
Wire feed pressure Start by making sure that the wire moves smoothly through the wire guide. Then set the pressure of the wire feeder’s pressure rollers. It is important that the pressure is not too great. Fig 1 Fig 2 To check that the feed pressure is set correctly, you can feed out the wire against an insulated object, e.g. -
Page 11: Maintenance
Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication. - - 11 - -... -
Page 12: Diagram
Diagram - - 12 - - bm36e11a... -
Page 13: Ordering Number
Feed 302 Ordering number Origot Feed 302, M11 0459 116 781 Origot Feed 302, M11 with water cooling 0459 116 791 Spare parts list 0459 206 990 - - 13 - - Edition 090325 bm36o11a... -
Page 14: Wear Parts
Feed 302 Wear parts Item Ordering no. Denomination Wire type Groove Wire dimensions Notes type 0455 889 001* Insert tube Fe, Ss & cored 0455 894 001* Insert tube 0455 886 001* Outlet nozzle Fe, Ss & cored 0455 885 001* Outlet nozzle 0369 716 001 Feed roller geared 0369 557 001... - Page 15 Feed 302 - - 15 - - R0459 206/E090325/P20 bm36whk1...
-
Page 16: Accessories
Feed 302 Accessories Bobbin cover, plastic 18 kg Ø 300mm ..0458 674 880 Bobbin cover, metal 18 kg Ø 300mm ..0459 431 880 Bobbin holder ......0458 704 880 Adapter for 5 kg bobbin . - Page 17 Feed 302 Turning piece ......0458 703 880 Guide pin ....... . 0156 654 883 Quick connector MarathonPact .
- Page 18 Feed 302 Counter balance device ....0458 705 880 (includes mast and counter balance) Connection set for 400 A power sources 1.7 m ........0469 836 880 5 m .
- Page 19 Feed 302 Welding gun with EURO connection Self cooled Type Ordering no. Max welding current Wire dimensions Hose length Hose length Mix Ar Cored 4.5 m 0368 100 882 0368 100 883 250A 60% 225A 60% 0.6 - - 1.0 0.6 - - 1.0 PSF 250 PSF 305...
- Page 20 ESAB subsidiaries and representative offices Europe Asia/Pacific Representative offices NORWAY AS ESAB AUSTRIA BULGARIA CHINA Larvik ESAB Ges.m.b.H ESAB Representative Office Shanghai ESAB A/P Tel: +47 33 12 10 00 Vienna- -Liesing Sofia Shanghai Fax: +47 33 11 52 03...